3,093
edits
Changes
Jump to navigation
Jump to search
==Interface==
[[File:X630-diagram.png|800px]]
==10-pin functional connector==
{| class="wikitable"
! Pin No. !! Pin Name !! Function !! Note
|-
| 1 || 3V3 || 3.3V output || 3.3V
|-
| 2 || HDET || HDMI input detect (high level ) || 3.3V
|-
| 3 || IR || Infrared signal || 3.3V
|-
| 4 || INT || Interrupt Output signal – active high (Level) || 3.3V
|-
| 5 || RESET || System reset input, active low || 3.3V
|-
| 6 || A_SCK || I2S/TDM Bit Clock signal (BCK) || 3.3V
|-
| 7 || A_WFS || I2S Word Clock or TDM Frame Sync signal (LRCK) || 3.3V
|-
| 8 || A_OSCK || Audio Oversampling Clock (MCLK) || 3.3V
|-
| 9 || A_SD || I2S/TDM data signal (Data) || 3.3V
|-
| 10 || GND || Ground || 0V
|}
==X630 Reset Setting==
'''Note: Software reset only exists in V1.3 version, this function is no longer reserved in V1.5'''
[[File:X630-V1.5-VS-X630-V1.3.jpg|700px|none|X630 V1.5 vs X630 V1.3]]
[[File:Dip-switches.jpg|none|dip switch]]
{| class="wikitable"
! SELECTION !! SWITCH SETTINGS !!
|-
| Hardware reset || HW = 1 || SW = 0
|-
| Software reset || HW = 0 || SW = 1
|}
[[File:X630-Reset-01.jpg|none|800px|X630 dip switch setting]]
Explain：
* Hardware reset: After starting RASPISTILL or RASPIVID <span style="color:red;">once</span> then you will need to reboot Raspberry Pi to restart it again (Please use when operating system cannot control the X630 module via GPIO509)
* Software reset: Starting RASPISTILL or RASPIVID <span style="color:red;">multiple times</span> and don't need to reboot Raspberry Pi
* Default setting is 'Hardware reset';
* Please remove the yellow protective film before change dip switch.
== Mechanical Drawing==
[[File:X630-mechanical-drawing.png|x630 mechanical drawing]]
Return to [[X630]]
<comments/>
[[File:X630-diagram.png|800px]]
==10-pin functional connector==
{| class="wikitable"
! Pin No. !! Pin Name !! Function !! Note
|-
| 1 || 3V3 || 3.3V output || 3.3V
|-
| 2 || HDET || HDMI input detect (high level ) || 3.3V
|-
| 3 || IR || Infrared signal || 3.3V
|-
| 4 || INT || Interrupt Output signal – active high (Level) || 3.3V
|-
| 5 || RESET || System reset input, active low || 3.3V
|-
| 6 || A_SCK || I2S/TDM Bit Clock signal (BCK) || 3.3V
|-
| 7 || A_WFS || I2S Word Clock or TDM Frame Sync signal (LRCK) || 3.3V
|-
| 8 || A_OSCK || Audio Oversampling Clock (MCLK) || 3.3V
|-
| 9 || A_SD || I2S/TDM data signal (Data) || 3.3V
|-
| 10 || GND || Ground || 0V
|}
==X630 Reset Setting==
'''Note: Software reset only exists in V1.3 version, this function is no longer reserved in V1.5'''
[[File:X630-V1.5-VS-X630-V1.3.jpg|700px|none|X630 V1.5 vs X630 V1.3]]
[[File:Dip-switches.jpg|none|dip switch]]
{| class="wikitable"
! SELECTION !! SWITCH SETTINGS !!
|-
| Hardware reset || HW = 1 || SW = 0
|-
| Software reset || HW = 0 || SW = 1
|}
[[File:X630-Reset-01.jpg|none|800px|X630 dip switch setting]]
Explain：
* Hardware reset: After starting RASPISTILL or RASPIVID <span style="color:red;">once</span> then you will need to reboot Raspberry Pi to restart it again (Please use when operating system cannot control the X630 module via GPIO509)
* Software reset: Starting RASPISTILL or RASPIVID <span style="color:red;">multiple times</span> and don't need to reboot Raspberry Pi
* Default setting is 'Hardware reset';
* Please remove the yellow protective film before change dip switch.
== Mechanical Drawing==
[[File:X630-mechanical-drawing.png|x630 mechanical drawing]]
Return to [[X630]]
<comments/>