5,123
edits
Changes
Jump to navigation
Jump to search
* [[X708-Software]]===Installation Video===* [[Installation Video for Raspberry Pi 4+X825 V1.5+X708/U100/X735+X825-Hardware]]C7 Case: https://youtu.be/kKIPf4AsiYY
AutoCAD Drawing Interchange Format file{{#ev: [[Fileyoutube|https:X708-PCB-V1//youtu.0.zip|none]]be/kKIPf4AsiYY}}
==FAQ==Q1:What battery is recommended Installation video for Raspberry Pi 4+X857 V1.2/X862 V1.0/X872 V1.1+X708?/U100+X857-C1 Case: https://youtu.be/HGPpfDbfyxM
A{{#ev:Please use big brand and high quality batteries, like PANPASONIC, Toshiba... [[Fileyoutube|https:18650_battery_size-2//youtu.jpg|400px]]be/HGPpfDbfyxM}}
Q3: How to restart the pi board when AC Power supply is connected?==FAQ== A: Please enable 'AUTO POWER ON' or 'AUTO ON' function if you want restart when the AC Power supply is reapplied. Q4: Which lithium battery can be used: A: to meet the following 2 conditions 1. Working voltage: 3.6V-3.7V 2. Maximum voltage after full: 4.2V Q5Q1: What type connector to request for lithium battery? A: X708 provides two type battery connectors: PH2.0-2P and XH2.54-2P, you can connect two battery at the same time, BUT please use the same model batteries, also please pay attention that the polarity of the XH2.54 and PH2.0 connectors is different. Q6: About auto shutdown, found your board will auto shutdown. A: Please check if enable the ASD function (shorted the ASD header), if you enable the ASD function, please sure your oeration is right: first, place the battery into the battery holder, insert the jumper to ASD header <span style="color:red;">after 3 second</span>,this is very important!! Q7: Does the recommended for X708 support to use without any battery installed? A: Yes, it is ok to use the X708 without battery, but please note that do not use low quality power supply. Q8: Why the X708 does not work normally? A: Please make sure you have install the script before use, please refer to [[X708-Software]] Q9:If "AON" is shorted, can you use a latching power switch to turn the x708 on/off, or is it on all the time, regardless of the switch? A:Sorry, this is not supported.'''
Q10'''Q2:Does What type connector to request for lithium battery?'''* A: X708 provides two type battery connectors: PH2.0-2P and XH2.54-2P, you can connect two battery at the X708 support to same time, BUT please use the latching switch?same model batteries, also please pay attention that the polarity of the XH2.54 and PH2.0 connectors is different.
Q11'''Q6: What About auto shutdown, found your board will auto shutdown.'''* A: Please check if enable the ASD function (shorted the ASD header), if you enable the ASD function, please sure your oeration is right: first, place the battery into the fan type of battery holder, insert the X708?jumper to ASD header <span style="color:red;">after 3 second</span>,this is very important!!
Q12'''Q9: Can If "AON" is shorted, can you use the X708 with a poe hat latching power switch to provide turn the x708 on/off, or is it on all the time, regardless of the powerswitch?'''* A:Sorry, this is not supported.
Q13'''Q12: Is there Can you use the X708 with a corresponding UPS NAS solution for 3poe hat to provide the power?'''* A: No, not suggest to use like this.5-inch hard drives?
==Installation Video==
Installation Video for Raspberry Pi 4+X825 V1.5+X708/U100/X735+X825-C7 Case: https://youtu.be/kKIPf4AsiYY
{{#ev:youtube|https://youtu.be/kKIPf4AsiYY}}
Installation video for Raspberry Pi 4+X857 V1.2/X862 V1.0/X872 V1.1+X708/U100+X857-C1 Case: https://youtu.be/HGPpfDbfyxM
{{#ev:youtube|https://youtu.be/HGPpfDbfyxM}}
<!--Please choose the -->
<!--Remove other categories, just keep the appropriate categories -->
X708
,{{GD Template Impl}}
[[File:X708-V2.0.jpg|thumb|X708 V2.0 UPS HAT]]
[[File:X708-V12-IMG-9489-interface.jpg|thumb|X708 V1.2 UPS HAT(Sold Out)]]
[[File:X708-IMG-8494-sche.jpg|thumb|X708 V1.0 UPS HAT(Sold Out)]]
[[File:X708-IMG-8515.jpg|thumb|X708 V2.0/V1.2/V1.0 UPS HAT]]
[[File:X708-IMG-8517-AM-1.jpg|thumb|right|X708 V2.0/V1.2/V1.0 Battery]]
[[File:X708-v2.0-01.jpg|thumb|right|X708+X728-A2]]
==Foreword==
<span style="color:red;"> NOTE: The X708 UPS DOES NOT support Raspberry Pi 5 hardware
===Why did X708 come out？===
* Improved AUTO ON function
* Added battery over-discharge function
* Improved power path management function: when external AC power is supplied, the AC PSU supplies power to the UPS shild shield and also charges the battery.
===X708 V1.2(off-production)===
# HAT size. Separate the battery from the expansion board, which can save a lot of space, which will bring more flexibility.
# Reserved two kind battery port (XH2.54 and PH2.0), supports 3.7V 18650 lithium battery and 3.7V lithium polymer battery, No capacity limit, only request '''3.7V''' lithium battery (No include lithium battery)
==Working principle==
The GPIO13 is used to control the power button, It goes high for 3 seconds that means the power switch is pressed and held for 3 seconds. then the X708 will issue a pulse to inform the system to implement safeshutdown via GPIO5, and will monitor the GPIO12, once shutdown process is implemented, GPIO 12 will go to low and will be recognized by the X708, then the X708 will wait for 7-8seconds then fully cut off power.
Firstly you have to get the script for power management well installed and run at boot. You can use the onboard power switch to verify , press and hold for 3 seconds, the blue LED will flash slowly and the shutdown is going then all LEDs will be off. once this works, then you can use the GPIO13 control.
The hardware and its firmware are verified. if you have a DMM, you can use it mesuare the GPIO voltage which will be helpful to understand above.
==Features==
<span style="font-weight:bold">Smart and powerful Uninterruptible Power Supply (UPS)</span>
* Provides continuous operations for up to 10~30hours (depending on battery type and qty used)
* Max 5.1V 8000mA 6000mA Power Backup for even the most demanding RPi set ups
* Supports 2A/3A fast battery charging
* Integrated over current protection and over voltage protection
| SPECIFICATION ||
* <span style="color:red;font-weight:bold">Power supply via Type-C socket: 5Vdc ±5%, ≥3A; Via DC power jack: 5Vdc ±5%, ≥4A</span>
* UPS output : 5.1V ±5% Max 8A. 6A
* UPS charging current: 1.8~2.2A / 2.3~3.2A
* Terminal Battery Voltage : 4.24V
* <span style="color:red;font-weight:bold">Do not use the battery with built-in protection circuit.</span>
|}
==How to Power==
* Power via DC5521 Jack of X708, 5.1Vdc +/-5% , ≥4A (DC5525 Jack is compatible with DC5521, also support 5V PSU with DC5525 Jack)
* Power via USB Type-C port of X708, 5.1Vdc +/-5% , ≥3A (Geekworm Type-C 5V 4A 20W power supply is recommended.）
==X728-C1==
X728-C1 is a metal case for X708 / X735 or X728 V2.2 / V2.1 / V2.0.
Installation Video: https://youtu.be/QOG30LXb6ds
<gallery>
01-IMG-3946-main.jpg|for X735/X708/X728 V2.x/
02-IMG-3892-开关卖点.jpg|with metal switch
03-IMG-3894-散热.jpg|active cool
04-IMG-3907-场景图.jpg|application
06-IMG-3941-size.jpg|dimension
IMG-3916-acce.jpg|x728-c1 Accessories
IMG-3945-GPIO排线.jpg|with GPIO hole
</gallery>
==Packing List==
==User Manual==
===Software & Hardware Guide===
* [[X708-script]]: This script is required to install to enable safe shutdown function.
* [[X708-Hardware]]: Provides some hardware parameter information
* AutoCAD Drawing Interchange Format file: [[File:X708-PCB-V1.0.zip|none]]
A:
* Pls use high quality batteries from PANPASONIC, Toshiba, etc.
* Lithium battery need to meet following 2 conditions: 1. Working voltage: 3.6V-3.7V; 2. Maximum voltage after full: 4.2V
* Do not use the battery with built-in protection circuit
[[File:18650_battery_size-2.jpg|400px]]
'''Q3: Is there a corresponding UPS NAS solution for 3.5-inch hard drives?'''* A:NoSorry, There is no UPS NAS solution for 3.5-inch hard drive because the X708 does not 3.5-inch hdd request 12V voltage, so we have no plans to support this demand for the time being. BUT you can refer to connect latching switchX835//X832, only support momentary switchand they can solve some of your needs, they need external power supply.
'''Q4: How to restart the pi board when AC Power supply is connected?'''
* A: Please enable 'AUTO POWER ON' or 'AUTO ON' function if you want restart when the AC Power supply is reapplied.
'''Q7: Does the X708 support to use without any battery installed?'''* A: It Yes, it is szie 3010 cooling fan with PH2.0-2P connectorok to use the X708 without battery, but please note that do not use low quality power supply.
'''Q8: Why the X708 does not work normally?'''
* A: Please make sure you have install the script before use, please refer to [[X708-Software]]
'''Q10:Does the X708 support to use the latching switch?'''* A: No, the X708 does not suggest support to use like thisconnect latching switch, only support momentary switch.
'''Q11: What is the fan type of the X708?'''
* A: It is szie 3010 cooling fan with PH2.0-2P connector.
'''Q13: Why does the X708 power off automatically?'''* A: Sorry, There is no UPS NAS solution for Please use 3.5-inch hard drive because the 3.5-inch hdd request 12V voltage7V lithium polymer battery without protection board, or battery with enough discharge capacity, so we have no plans to support this demand for or the time beingX708 will power off automatically when use with high load. BUT you can refer Refer to X835video test: https://X832, and they can solve some of your needs, they need external power supplyyoutu.be/Saco6rJm4ZQ
<!--Add review function! -->
<comments />
[[Category:Product Manual]]
[[Category:Raspberry pi]]