Open main menu

X635-Software

Revision as of 09:27, 14 August 2023 by Cindy (talk | contribs) (→‎Flash OS onto the NVME SSD)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

X635 Software Guide base on Raspberry Pi OS bullseye

Contents

Installing the Operating System

Flash OS onto the Micro SD card (CM4 without eMMC)

Please refer to Official installation tutorial

Flash OS onto the NVME SSD

You need to refer to the above steps to flash the OS into the Micro SD card, then insert the Micro SD card, turn on the device, and then click Applications =>Accessories =>SD Card Copier, run the SD Card Copier program, and copy the OS to the NVME ssd as shown in the figure below.

 

Click Start to run. Then shut down, unplug the SD card, and restart the device.

Flash OS onto the eMMC of CM4 (CM4 with eMMC)?

1. Short nBoot Pin, refer to the picture below

 

2. Connect Type-C OTG with a Type-A to Type-C cable to your computer

3. Power the device via PWR Type-C with your 5V Power adaper

4. Then rerfer to this tutorial to flash raspberry pi OS

5. Remove the jumper of nBoot after flashing is complete, then continue the following steps;

PS:If you use CM4 with eMMC, then SD card cannot be used.

Preconfigure X635 Device for CM4

If you attempt to boot now you will not have working USB ports, ssh, or any wireless configuration.

We can preconfigure your CM4 device by plugging mico sd via sd reader into a windows computer / Pi. You should see the “boot” volume where we can preconfigure our CM4 to be working right from the start.

Enable USB Ports

When mounted in the IO board the USB ports will not function without making a change to config.txt and adding an overlay.

Add the following line to config.txt:

dtoverlay=dwc2,dr_mode=host

After adding this line the two USB ports (as well as the “External USB” header) will function the next time the CM4 boots.

Enable SSH

It's very useful to have SSH enabled when working with the Compute Module 4. It is enabled simply by creating an empty file named:

ssh

in the root folder of the “boot” volume (the top-most folder of the drive where start4x.elf, fixup.dat and those files are located)

Now when the Pi starts up SSH will automatically be enabled!

Preconfigure WiFi / Wireless

You can also preconfigure the Compute Module 4 (and any Pi) by creating wpa-supplicant.conf at the base of the “boot” volume like we did with “ssh” file.

Create a new file named wpa-supplicant.conf that contains the following:

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
country=US
update_config=1

network={
 ssid="YourNetwork"
 psk="YourPassword"
}

When this file is created in the base of the “boot” volume it will automatically be applied to the Pi upon the next startup. Make sure to adjust your country=US line to your own country as this can impact what channels and functionality are available from your WiFi card!

Then you can insert your micro sd card into the X635 & power on it.

Enable legacy camera support

After you power on the x635, to use the HDMI to CSI-2 bridge, you will need to Enable legacy camera support

Download dt-blob.bin File

Run the following command:

sudo wget https://datasheets.raspberrypi.org/cmio/dt-blob-cam1.bin -O /boot/dt-blob.bin

Then reboot for the dt-blob.bin file to be read.

sudo reboot

Check HDMI to CSI-2 bridge

Open the Terminal and run the command to check if the HDMI to CSI-2 bridge is being seen by the operating system.

 

Note: You should get back supported=1, detected=1, indicating that the CSI-2 bridge is detected and supported by the operating system. If you get detected=0, then the CSI-2 bridge is not being seen by the operating system.

Test x635 shield via command line

Connect the HDMI source device

Before testing the X635, you must connect your HDMI signal source device into X635 as the HDMI in HDMI to CSI-2 bridge with mini HDMI to HDMI wire.


IMPORTANT! The HDMI to CSI-2 bridge only accepts HDMI input: 1080p30, 1080p25, 720p30, 720p25

Picture test

Record a sample picture: open a terminal window and run the following command to take a still picture and save it to the Desktop:

raspistill -o Desktop/image.jpg

When the command runs, you can see the camera preview open for five seconds before a still picture is taken.

Video test

Record a sample video using the following raspivid command:

raspivid -o Desktop/video.h264

 

In order to play the video file, double-click the video.h264 file icon on the Desktop to open it in VLC Media Player.

Advanced application


Or refer to http://www.suptronics.com/miniPCkits/x635-software.html


Return to X635


Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.