Difference between revisions of "X635-Software"
| Line 2: | Line 2: | ||
<big>X635 Software Guide base on Raspberry Pi OS bullseye</big> | <big>X635 Software Guide base on Raspberry Pi OS bullseye</big> | ||
| − | + | 1. To use the HDMI to CSI-2 bridge, you will need to enable '''[[How to enable camera support in Raspberry Pi OS|Enable legacy camera support]]'''. | |
| − | + | 2. Again open a terminal window and type the following command: | |
sudo wget https://datasheets.raspberrypi.org/cmio/dt-blob-cam1.bin -O /boot/dt-blob.bin | sudo wget https://datasheets.raspberrypi.org/cmio/dt-blob-cam1.bin -O /boot/dt-blob.bin | ||
#Download the required file /boot/dt-blob.bin | #Download the required file /boot/dt-blob.bin | ||
| − | + | 3. Reboot for the dt-blob.bin file to be read | |
sudo reboot | sudo reboot | ||
| − | + | 4. Open the Terminal and run the command to check if the HDMI to CSI-2 bridge is being seen by the operating system. | |
[[File:X635-software-15.png|700px]] | [[File:X635-software-15.png|700px]] | ||
| Line 17: | Line 17: | ||
Note: You should get back <big>supported=1, detected=1</big>, indicating that the CSI-2 bridge is detected and supported by the operating system. If you get detected=0, then the CSI-2 bridge is not being seen by the operating system. | Note: You should get back <big>supported=1, detected=1</big>, indicating that the CSI-2 bridge is detected and supported by the operating system. If you get detected=0, then the CSI-2 bridge is not being seen by the operating system. | ||
| − | + | 5. Connect the HDMI in device to x635 carrier board. | |
connection sample diagram | connection sample diagram | ||
<big>IMPORTANT! The HDMI to CSI-2 bridge only accepts HDMI input: 1080p30, 1080p25, 720p30, 720p25</big> | <big>IMPORTANT! The HDMI to CSI-2 bridge only accepts HDMI input: 1080p30, 1080p25, 720p30, 720p25</big> | ||
| − | + | 6. Test x635 shield via command line | |
| − | 1. Record a sample picture: open a terminal window and run the following command to take a still picture and save it to the Desktop: | + | 6.1). Record a sample picture: open a terminal window and run the following command to take a still picture and save it to the Desktop: |
raspistill -o Desktop/image.jpg | raspistill -o Desktop/image.jpg | ||
When the command runs, you can see the camera preview open for five seconds before a still picture is taken. | When the command runs, you can see the camera preview open for five seconds before a still picture is taken. | ||
| − | 2. Record a sample video using the following raspivid command: | + | 6.2). Record a sample video using the following raspivid command: |
raspivid -o Desktop/video.h264 | raspivid -o Desktop/video.h264 | ||
[[File:X635-software-18.png|700px]] | [[File:X635-software-18.png|700px]] | ||
In order to play the video file, double-click the video.h264 file icon on the Desktop to open it in VLC Media Player. | In order to play the video file, double-click the video.h264 file icon on the Desktop to open it in VLC Media Player. | ||
| + | |||
| + | 7. Install GStreamer on CM4 - For advanced programmers and advanced applicaitons | ||
| + | 7.1) Check out this link - https://qengineering.eu/install-gstreamer-1.18-on-raspberry-pi-4.html | ||
| + | |||
| + | 7.2) GStreamer official website: https://gstreamer.freedesktop.org/ | ||
<!--Add review function! --> | <!--Add review function! --> | ||
Revision as of 19:48, 24 April 2023
X635 Software Guide base on Raspberry Pi OS bullseye
1. To use the HDMI to CSI-2 bridge, you will need to enable Enable legacy camera support.
2. Again open a terminal window and type the following command:
sudo wget https://datasheets.raspberrypi.org/cmio/dt-blob-cam1.bin -O /boot/dt-blob.bin #Download the required file /boot/dt-blob.bin
3. Reboot for the dt-blob.bin file to be read
sudo reboot
4. Open the Terminal and run the command to check if the HDMI to CSI-2 bridge is being seen by the operating system.
Note: You should get back supported=1, detected=1, indicating that the CSI-2 bridge is detected and supported by the operating system. If you get detected=0, then the CSI-2 bridge is not being seen by the operating system.
5. Connect the HDMI in device to x635 carrier board. connection sample diagram
IMPORTANT! The HDMI to CSI-2 bridge only accepts HDMI input: 1080p30, 1080p25, 720p30, 720p25
6. Test x635 shield via command line 6.1). Record a sample picture: open a terminal window and run the following command to take a still picture and save it to the Desktop:
raspistill -o Desktop/image.jpg
When the command runs, you can see the camera preview open for five seconds before a still picture is taken.
6.2). Record a sample video using the following raspivid command:
raspivid -o Desktop/video.h264
In order to play the video file, double-click the video.h264 file icon on the Desktop to open it in VLC Media Player.
7. Install GStreamer on CM4 - For advanced programmers and advanced applicaitons 7.1) Check out this link - https://qengineering.eu/install-gstreamer-1.18-on-raspberry-pi-4.html
7.2) GStreamer official website: https://gstreamer.freedesktop.org/
Enable comment auto-refresher