Difference between revisions of "X630-A8"
| Line 28: | Line 28: | ||
==Packing List== | ==Packing List== | ||
| − | ''' | + | * '''1 x X630-A8 V1.7 Expansion Board''' |
| − | * 1 x FPC cable (Length: 5cm) | + | * * 1 x FPC cable (Length: 5cm) |
| − | + | * * 1 x ATX Control Cable (Length: 52cm) | |
| − | + | * * 1 x Motherboard Internal USB 2.0 9-pin Female Header to TYPE-C USB OTG Cable (Length: 50cm) | |
| − | + | * * 1 x USB3.0 IDC to TYPE-C (Length: 45cm) | |
| − | + | * * 1 x Standard height PCIe Add-in Card I/O Bracket | |
| − | + | * * 4 x M2.5x12mm F/F Spacers | |
| − | + | * * 8 x M2.5x6mm Screws | |
| − | ''' | + | * '''1x X630-A8-CAB V1.1 Camera Adapter board''' |
| − | * 2 x PM3x6mm Screws | + | * * 2 x PM3x6mm Screws |
<!--Add review function! --> | <!--Add review function! --> | ||
Revision as of 12:39, 19 November 2022
Overview
This is the PCIe KVM-A8 kit that allows user to realize a PiKVM / KVM project with Raspberry Pi 4.
NO extral connection wire require, easy to assemble and use.
PiKVM (https://pikvm.org/) is a very powerful and Open Source Software which allows for a remote connection via your Raspberry Pi to turn on/off or restart your computer, configure the UEFI/BIOS, and even reinstall the OS using the Virtual CD-ROM or Flash Drive. You can use your remote keyboard and mouse or PiKVM can simulate a keyboard, mouse, and a monitor, which are then presented in a web browser as if you were working on a remote system directly. It’s true hardware-level access with no dependency on any remote ports, protocols or services!
X630-A8 is an accessory for PiKVM-A8 (Raspberry Pi 4 based KVM over IP, PCIe version)，the complete kit or other PiKVM version, please refer to PiKVM
Features
- Designed especially for PiKVM (Raspberry Pi 4-based KVM over IP)
- Installs justs like any PCI card into a tower / desktop PC
- Fully compatiblie with PiKVM OS
- Reliable remote network access to servers and computers
- HDMI Full HD capture based on the TC358743 chip (from X630)
- OTG Keyboard & mouse; Mass Storage Drive emulation
- Hardware Real Time Clock (RTC) with CR1220 coin battery socket
- Equipped with cooling fan that allows the heat from your Raspberry Pi to dissipate
- Equipped with photocoupler to protect RPi GPIO pins from computer and ESD spikes
- PoE Supported – Power over Ethernet for simplified installation
- Also supports for powering via USB-C
- Reserves the PH2.04P connector for I2C OLED display
Packing List
- 1 x X630-A8 V1.7 Expansion Board
- * 1 x FPC cable (Length: 5cm)
- * 1 x ATX Control Cable (Length: 52cm)
- * 1 x Motherboard Internal USB 2.0 9-pin Female Header to TYPE-C USB OTG Cable (Length: 50cm)
- * 1 x USB3.0 IDC to TYPE-C (Length: 45cm)
- * 1 x Standard height PCIe Add-in Card I/O Bracket
- * 4 x M2.5x12mm F/F Spacers
- * 8 x M2.5x6mm Screws
- 1x X630-A8-CAB V1.1 Camera Adapter board
- * 2 x PM3x6mm Screws
Enable comment auto-refresher