Sackable & universal UPS shiled, 12V & 5V dual output voltage for all SBC
X-UPS V1.3 Accessories & Dimension
X-UPS1 V1.3 Interface Schematic
X-UPS1 V1.3
X-UPS1 V1.3
X-UPS1 V1.3
X-UPS1 UPS with Acrylic Plate
Contents
Overview
The X-UPS1 is an universal stackable uninterruptible power supply (UPS) shield for most Single-Board Computers (SBC) that uses 12Vdc or 5Vdc. The UPS ensures that in event of power interruption, a battery or any other power source will intervene without any effect on your board.
Our convenient stackable design allows you to connect several UPS modules on your boards to provide long-lasting & higher output power.
SAFETY INSTRUCTIONS AND WARNINGS
You must read these safety instructions and warnings before charging your batteries.
Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the below instructions may result in fire, personal injury and damage to property if charged or used improperly.
Never make wrong polarity connection when charging and discharging battery packs. Always double check polarity of battery's connector to make sure "+" to "+" and "-" to "-".
Do not mix and use old batteries and new batteries, or batteries with different brand names.
Lithium batteries has it's cycle life, please replace old battery with new one when it reaches it's service life or when it is two year old, whichever comes first.
When charging Battery Pack, please put battery in a fire proof container. Please don't leave the X-UPS1 on the wood material or carpet and unattended.
Up to 10A output current to keep 3A fast charging and powering your SBC at the same time
Allows powering from a car, a solder pannel and other power sources
Most common power input jack: 5.5x2.1mm
Power Control
Onboard push button to control power on /off (PressON, Hold the button pressed at least 3s OFF )
Onboard LEDs shows the status of power output
AC power loss or power adapter failure detection (LED and 3.3V level output)
Jumper setting to enable Auto power on when power applied or restored
Jumper setting to disable 12V output
Ultralow standby power consumption to maximize battery life
Advanced system powerpath management avoids batteries frequent charging and discharging
Misc
Power output connectors : VH3.96 x2 (12V) / XH2.54 x2 (5V) / USB TypeA x2 (5V)
PH2.0-4P for external power switch
PH2.0-4P for low battery and AC power loss deteciton
Spec
Power input (Single board) : 6-24Vdc ±5%, ≥3A
UPS output voltage : 12Vdc ±5%, 5.1Vdc ±5%
UPS output current (Single boards) : Max 3A
UPS output current (Stackable boards) : 3A x No. of the boards
UPS charging current (Single board) : 2.3~3.2A
Terminal Battery Voltage : 4.24V
Battery Recharge Threshold : 4.1V
Battery low detection: ≤3V
Note
Notes for stackable application:
All power input are connected together via the 18-pin female header, output current is subject to the quantity of boards.
You can use same one board to turn on/off all stackable boards. (be noted that which board you press the button to turn on, also must the same board to turn off.)
Only one AL_ON jumper caps be shorted to enable Always Power On when stacked multiple x-ups1 shields.
MUST ALL 12 OFF jumper caps be shorted to disable 12V output when stacked multiple x-ups1 shields.
Packing List
1 x X-UPS1 Expansion Board
1 x VH3.96 to DC5525 Cable (50cm length, to 12V output)
1 x XH2.54 to DC5521 Cable (50cm length, to 5V output)
1 x 4Pin PH2.0 to dupont cable (30cm length, this is a signal & 5V Output Cable)
1 x GPIO Header
2 x Jumper link Pitch 2.54mm
4x Spacer F/F M2.5x10mm
4 x Spacer M/F M2.5x25+6mm
4 x Screw M2.5 x 5mm
User Manual
X-UPS1 V1.3 Jumper Cap & Button Switch Guidance:
Application
Compatible with Most Single Board Computers (SBC) that uses 12Vdc or 5Vdc, SBC Example: Orange Pi 5 / Jetson Nano / Raspberry Pi / Tinker Board / Arduino etc.
X-UPS1 for Raspberry Pi
X-UPS1 for Orange Pi
X-UPS1 for Jetson Nano
PCB Dimension
X-UPS1 Dimensions source file (DXF): File:X-UPS1-PCB.dxf - You can view it with Autodesk Viewer online
Hello, button top of flat top 18650? Protection circuit? For US users, it's be helpful to link to batteries on imrbatteries.com, as they specify many details like that.
Can you PLEASE just post the physical dimensions. The DXF file does not self-calibrate. It's really weird you don't just have the dimensions on the product description.
Enable comment auto-refresher
Anonymous user #6
Permalink |
Lisa
Anonymous user #5
Permalink |
Anonymous user #4
Permalink |
Walker
Anonymous user #3
Permalink |
Walker
Walker
Anonymous user #3
Permalink |
Anonymous user #2
Permalink |
Walker
Anonymous user #1
Permalink |
Walker