Related changes
Jump to navigation
Jump to search
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
17 May 2024
|
|
05:59 | (Comments log)[216.24.212.246; 216.24.212.210] | |||
|
|
05:59 216.24.212.210 talk posted a new comment on X1201 (would NOT take a charge) | ||||
|
|
05:58 216.24.212.246 talk posted a new comment on X1201 (Yes, the batteries were hardly used but one was bad; it would take a charge. Thanks) | ||||
15 May 2024
| 04:38 | Comments log 172.59.122.138 talk posted a new comment on How to enable OLED display (you say: Hi, you can ignore python-smbus package I ask: How Instructions do not work at all. Many failures.) | ||||
13 May 2024
|
|
16:21 | (Comments log)[112.220.71.122; 104.28.42.26] | |||
|
|
16:21 104.28.42.26 talk posted a new comment on XScript (I have the same problem...) | ||||
|
|
12:47 112.220.71.122 talk posted a new comment on X1001 (My raspberry PI 5 server has - raspberry PI 5 4 GB - 25W power supply ( 5V 5A ) - Geekworm X1001 PICe HAT - SD Card 64GB - OS: Bookworm 64Bit My PI5 system halts within 3-4 hours from system boot. I tried to mount the SSD (1GB, Samsung Electronics) and booted from SSD successfully without SDCard. But with or without SSD, the system halts after 3~4 hours. When I disconnected X1001 HAT and the PI board( plug off the PICe ribbon cable from X1001 HAT), the system does not freeze for severa...) | ||||
10 May 2024
| 14:37 | Comments log 172.114.135.75 talk posted a new comment on X1202 (I noticed that the x1202 always said "AC Power OK" even with power plug disconnected. As the pld.py code ran I could press down on the Pi board and the x1202 would say "AC Power Loss". When I let up it would go back to "AC Power OK". Seems like a pogo is not making good contact. Any suggestions?) | ||||
9 May 2024
| 15:59 | Comments log 95.73.54.49 talk posted a new comment on How to Configure RAID Setting (Hi, How can I check health of the each disk in hardware RAID mode?) | ||||
7 May 2024
|
|
21:47 | (Comments log)[84.50.46.206; 23.114.212.80 (2×); 1.64.154.121 (3×)] | |||
|
|
21:47 1.64.154.121 talk posted a new comment on XScript (I also using raspberryOS 64bit(bookworm)) | ||||
|
|
21:45 1.64.154.121 talk posted a new comment on XScript (Hi, I followed this guide and now xoff works, but the fan not move at all. It show active and enabled when I enter "sudo systemctl status x-c1-fan.service". Is it the fan broken or have any suggestion to debug?) | ||||
|
|
09:07 23.114.212.80 talk posted a new comment on X1202 (One of the pogos looks like it contacts the area for the Real-time battery. Does this also supply power for that port?) | ||||
|
|
09:06 23.114.212.80 talk posted a new comment on X1202 (What are the specs on the momentary switch port? Does this work like one on the board?) | ||||
|
|
07:50 84.50.46.206 talk posted a new comment on X735-script (I decided to run Home Assistant OS as a virtual machine using Incus so I could use the X735 following the instructions on this wiki page. Fan now is quiet and PWM is doing its thing. I followed the steps here, but I used <code> pip3 install --break-system-packages rpi-lgpio </code> for installinh the GPIO library. To check if the services are working I used <code> systemctl status x735-fan </code> and <code> systemctl status x735-pwr </code> For troubleshooting it helps to check...) | ||||
|
|
02:17 1.64.154.121 talk posted a new comment on XScript (Hi, is there a version of Debian 12(Bookworm)? I'm using NASPi and the fan not working and "xoff: command not found" after install script.) | ||||
6 May 2024
| 04:17 | Comments log 216.24.212.37 talk posted a new comment on X1201 (X1201 V1.1 current behavior: On applying power starts charging and starts Pi5 via attached USB-C. When fully charged stops charging, quits using UBS-C power and uses power from the battery. When battery are depleted, shuts off everything. Also when you remove USB-C power, it does not transition to battery is shuts off everything. There is no software installed in crons or anything. This is not a seamless UPS. Is there a jumper of GPIO setting that I don't have set?) | ||||