X301

X301 2.5" sata shield for Pi Zero 2 W

X301 2.5" sata ssd interface

X301 Packing List

X301 shield + C296

X301 pcb size

Overview

This X301 is a 2.5-inch SATA HDD/SSD storage expansion board with USB HUB function for the raspberry pi zero 2 w.

Geekworm has provided X-series storage solutions for Raspberry Pi since 2017, our storage expansion boards have been continuously improved with the upgrade of Raspberry Pi. Many Geekworm users contacted us to inquire about the Zero 2 W storage expansion board, that is why the X301 is born.

Note:

X301 is only compatible with Raspberry Pi Zero 2W, NOT support other raspberry pi zero board.
Raspberry pi micro OTG port cannot be used as it is occupied by USB HUB

Features

Ideal storage solution for Raspberry Pi Zero 2 W - 2.5" SATA HDD/SSD Shield
USB Hub for Raspberry Pi Zero 2W
Gain 3 USB2.0, downstream ports which offer High-Speed (480Mbps), Full-Speed (12Mbps), and Low-Speed (1.5Mbps)
Supports Multiple Transaction Translators for optimum performance
Powers the Raspberry Pi via Pogo Pins - no wiring & soldering required
LED green indicates RPi activity status and LED blue indicates hard drive status
Supports USB Attached SCSI Protocol (UASP)

How to Power

Power via USB C 5V In port of X301

Power supply requirement: 5Vdc +/-5% , ≥3A

How to Cool

Recommend to use with Geekworm C296 aluminum heatsink for Raspberry Pi Zero 2 W. C296 also compatible with raspberry pi zero w by using thermal pads of different thicknesses, thermal pads for raspberry pi zero w is not included.

Packing List

1 x X301 V1.0 Expansion Board
4 x F/F M2.5*12 mm Spacers
4 x CM2.5*5mm Screws
2 x CM2.5*10mm Screws
2 x M3*5mm Screws (to fix HDD)

PCB dimention

X301 Dimensions source file (DXF): File:X301-V1.0-DWG.dxf - You can view it with Autodesk Viewer online

User Manual

FAQ

Q1: Does the X301 support boot from the ssd/hdd?

A: No, the Raspberry Pi Zero 2W does not support boot from SSD/HDD.

Enable comment auto-refresher

Anonymous user #5

3 months ago

Score 0

The Pi Zero 2 W DOES support boot from USB out of the box. I have tried both a USB thumbdrive and an SSD through a USB SATA adapter on an OTG-to -USB cable. All work fine. But for some reason the X301, which is essentially an OTG adapter, does not allow booting from the HDD/SSD attached. Big disappointment.

Permalink | Reply

Anonymous user #5

3 months ago

Score 0

If you FAT32 format an SD card and put the bootcode.bin file from PiOS on it, you are able to boot from the X301 attached hdd/ssd. There is also an anclosure available to 3D print on the Printables website.

Permalink

Anonymous user #4

4 months ago

Score 0

How does the X301 connect to SATA drives? Is there a place to plug in a SATA cable?

Or are you recommending that a USB to SATA adapter cable be used?

Permalink | Reply

Lisa

4 months ago

Score 0

Hello,X301 has a SATA SSD interface, no sata cable required.

Permalink

Anonymous user #3

4 months ago

Score 0

Hello! I have raspberry PI Zero 2W.

I in installed Ubuntu Server 22.04 on it and ETH port and USB ports are not available. is there anydditional driver for Ubuntu for x301?

Permalink | Reply

Lisa

4 months ago

Score 0

Hello，may be a problem with some software settings, but we have not tested Ubuntu Server 22.04 yet, and we will update the wiki if we find any results.

Permalink

Anonymous user #2

19 months ago

Score 0

By making the screw holes for attaching the sdd/hdd threaded you make it nearly impossible to attach the sdd/hdd. When I did get the screw to catch the drives threaded hole the drive is not against the built-in stand off.

Permalink | Reply

Walker

18 months ago

Score 0

Hello, there are many types of hard disks. It may be caused by the compatibility of the hard disk. It is recommended that you replace the hard disk. Generally, there is no problem with the screws.

Permalink

Anonymous user #2

19 months ago

Score 0

Can the x301 be powered by the header pins on the pi zero?

I am wanting to use a pi hat ups for backup power.

Permalink | Reply