EDP to HDMI Adapter

EDP to HDMI Adapter V1.3-Front

EDP to HDMI Adapter V1.3-Back

EDP to HDMI Adapter V1.3 Interface

EDP to HDMI adapter V1.2-Front

EDP to HDMI adapter V1.2-Back

EDP to HDMI Adapter V1.2 Interface

Overview

S.EDP-HDMI-4K2K.V1.2 is a signal adapter board, which is mainly used to convert EDP signal into HDMI signal, the resolution of this adapter supports up to 4K 30HZ resolution. The adapter can be used in set-top boxes, advertising machines, conference systems and other fields. EDP input needs to comply with EDP1.1, EDP1.2 standards;

Update History: Update to V1.3 version from V1.2 version in December 2022, and add the EDP SET switch to switch 2LANE and 4LANE.

Important Note

1.For general computers or industrial motherboards:
These adaptive output motherboards typically support only 1080P(2 lane) or 4K(4 lane) resolutions. Resolutions below 1080p or equal to 2K CAN NOT be supported. To support 1080p resolution please make sure that the motherboard meets the 2-lane EDP requirement. Please DO NOT use it to connect your PC if the resolution of your screen is not 1080P or 4K.

2.For Android/Linux solutions from Qualcomm, Rockchip, Allwinner, or certain LCD driver boards:
These solutions usually use fixed output EDP signals. Make sure these signals can output standard resolution and refresh rates and adhere to HDMI timing specifications, then EDP to HDMI adapter will support 1/2/4 lane EDP signals.

Features

Features ( EPD/DP RX )：

Compliant with VESA EDP/DP1.2
Support 1.62/2.7/5.4Gbps
Support 1/2/4 lanes （Default with 2 lanes program）
Support SSC
1Mbps AUX channel
Compliant with HDCP1.3

Features ( HDMI TX)：

Compliant with HDMI2.0, HDMI1.4 and DVI1.0
Compliant with HDCP2.2 and HDCP1.4
IData rate up to 6Gbps
Support UHD 4k@60Hz(RGB and YCbCr 4:4:4)
Support TMDS scrambling for EMI/RFI reduction
Support SCDC(Status and Control Data Channel)

Configuration & General Precautions

Relative humidity: ≤ 80%.
Storage temperature: -20~60°C.
Operation temperature: -20~60°C.
Protect the board from static electricity in case of damage to the IC.
Keep the board away from conductor when it is working.
Don't wire in the board to power supply before panel is correctly connected.
Operating:Less than 2000m

Power Supply

The EDP to HDMI Adapter obtains power through 30 Pin 2 lane port or 40 Pin 4 lane prot.
Default power supply voltage: 3.3V. After upgrading hardware components the voltage can be increased to 5-12V. Contact us if you need custom boards with an operating voltage of 5-12V.

Packing List

1 x EDP to HDMI adapter board(2lanes program)

User Manual

Document: File:S.EDP-HDMI-4K2K.V1.2-Specifications.pdf

EDP cable to EDP adapter board Definition

30Pin 40Pin

EDP cable to Screen Definition

30pin

40pin

FAQ

Q: The adapter board is connected to the EDP signal, but there is no HDMI output?

Please check whether the EDP cable is connected correctly, differential signal and power supply.
The power supply voltage should be above 4.5V.
EDP output to distinguish VESA compliance, refer to point 6 of user manual.

Q: The HDMI output picture is normal, but the color of the picture is abnormal?

The data format of the EDP signal does not match the configuration of the adapter board, single 8 or double 8.
EDP signal board need to adjust program or enter the factory menu to set EDP MAP (VESA or JEIDA).
The adapter board upgrades the program and reconfigures the parameters.

Q: The size of the HDMI output picture abnormal or the position shifted?

The EDP signal board should adjust the EDP parameters strictly according to the VESA standard configuration, refer to point 6 of user manual for common resolutions.

Q: The HDMI output screen jittery, flickering and other unstable phenomena?

Focus on checking the EDP signal parameter configuration, turn off the spread spectrum (NOSSC) of EDP output, and turn on the FREERUN function.

Q: Does this adapter support 1080p up to 240hz?

No, the adapter can only support 1080p up to 60hz.