X-UPS1

Sackable & universal UPS shiled, 12V & 5V dual output voltage for all SBC

Contents

Overview

The X-UPS1 is an uninterruptible power supply (UPS) stackable module for most Single-Board Computers (SBC) that uses 12Vdc or 5Vdc. The UPS ensures that in event of power interruption, a battery or any other power source will intervene without any effect on your board.

Our convenient stackable design allows you to connect several UPS modules on your boards to provide long-lasting & higher output power for even the most demanding SBC set ups that have constant power connections 24 hours a day, seven days a week.

PCB dimention

X-UPS1 Dimensions source file (DXF): File:X-UPS1-PCB.dxf - You can view it with Autodesk Viewer online

Add your comment

Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.

Sort by date Sort by score

Enable comment auto-refresher

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #7

4 days ago

Score 0

For the external switch the description on the PCB says power(black), Gnd(red), Gnd(yellow), and SW(blue) In that exact order on a psw19 or any 4 prong switch you have positive, negative, NO, and C Please show wire diagram for of the PH2.0 signal cable connector and the external momentary switch

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Lisa

one day 2 hours 38 minutes ago

Score 0

Hi,please refer to PSW19---Power Switch Wiring Diagram

Permalink

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #6

one month ago

Score 0

When multiple boards are stacked can I use the outputs on all boards, or only the first? Thanks!

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Lisa

one month ago

Score 0

Hello,you can use the output of one of the UPS boards

Permalink

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #5

4 months ago

Score 0

Can you post example usage of the PH2.0 signal cable connector and the external momentary switch connector.

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #4

5 months ago

Score 0

Hello, button top of flat top 18650? Protection circuit? For US users, it's be helpful to link to batteries on imrbatteries.com, as they specify many details like that.

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Walker

5 months ago

Score 0

Pls use high quality batteries from PANPASONIC, Toshiba, etc.

Do not use the battery with built-in protection circuit.

Permalink

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #3

8 months ago

Score 0

Is it possible to read the voltage and capacity in python?

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Walker

8 months ago

Score 0

Hello, Onboard 4 green LEDs indicate battery charging and discharging levels of 25%, 50%, 75% and 100%. Only these ranges can be displayed.

Permalink

You are ignoring the author of this comment

Show comment | Manage ignore list

Walker

8 months ago

Score 0

Hello, it’s not possible. It can only display a range and cannot read specific values in python.

Permalink

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #3

8 months ago

Score 0

GPIO pin layout?

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #2

8 months ago

Score 0

Please tell me the operating temperature range and storage temperature range.

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Walker

8 months ago

Score 0

Hello, usually between 0-50 degrees

Permalink

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #1

10 months ago

Score 0

Can you PLEASE just post the physical dimensions. The DXF file does not self-calibrate. It's really weird you don't just have the dimensions on the product description.

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Walker

10 months ago

Score 0

You can refer to the size chart here:

Permalink