Difference between revisions of "X708-Hardware"

Latest revision as of 17:04, 1 March 2024

4-Pin Function Header for X708 V1.2

❶ Power Jack and Connectors

Power input	5Vdc +/- 5% , ≥3A
DC Power Plug Size	5.5*2.5mm
USB power in socket	Type-C
UPS power output	5.1Vdc 8A(Max.)
Power output connector	2-pin XH2.54mm *2

X708 powers the Raspberry Pi via the 40-pin header (Pin 2 & 4)
Don't power the Raspberry Pi via the Pi's type-C USB socket
X708 can be powered via the onboard DC jack or Type-C USB power socket

❷ 6-Pin Function Header for X708 V1.0

Jumper Name	Usage
PLD (Power loss detection) Pin 1&2	Short - AC Power loss or power adapter failure detection enabled (Active if power adapter disconnected) Open - Power loss detection disabled
AON (Auto power-on) Pin 3&4	Short - Auto power-on when power applied (Will delay 3 seconds before powering on) Open - Auto power-on disabled
ASD (Auto shutdown) Pin 5&6	NOTE: ASD fundtion is removed on V1.2 version,but you can achieve this function through software programming. Short - Automatic shutdown enabled when battery low (≤3Vdc ) Procedure to enable ASD function --IMPORTANT 1. Battery voltage must be >3Vdc 2. Insert the battery into the holder 3. Wait 3 seconds then insert the jumper 4. If the jumper inserted before battery, remove battery & jumper then repeat step 1, 2 and 3. Open - Automatic shutdown disabled

❸ How to connector external power switch

Pin No.	Pin Description
1	Power on/off control connecting to switch
2	Ground
3	Ground
4	LED+ for power on, rebooting and shutdown

❹ Power button (Script for power mgnt installed)

Press and Release	Raspberry Pi and X708 turn on
Press and hold for 1~2 seconds	System rebooting
Press and hold for 3~7 seconds	System shutting down
Press and hold for >8 seconds	Force shutdown

❺ Function LEDs

LED Name	Usage
BAT LOW	LED red on indicates battery low (≤3.0Vdc) or blue power button pressed (Jumper for ASD inserted)
5V OUT	LED green on flashing indicates 5V power out and UPS powered by battery
AC FAIL	LED red on indicates AC power loss or PSU failure or PSU disconnected
PWR	LED blue indicates Stays on - Power on Blinks rapidly - system rebooting Blinks slowly - Shutting down

❻ Fuel gauge - LED Indicator

Operation of Discharging

Capacity C (%)	D1	D2	D3	D4
C ≥75%	ON	ON	ON	ON
50%≤C＜75%	ON	ON	ON	OFF
25%≤C＜50%	ON	ON	OFF	OFF
3%≤C＜25%	ON	OFF	OFF	OFF
0%＜C＜3%	Flashing	OFF	OFF	OFF

Operation of charging

Capacity C (%)	D1	D2	D3	D4
Fully charged	ON	ON	ON	ON
75%≤C	ON	ON	ON	Flashing
50%≤C＜75%	ON	ON	Flashing	OFF
25%≤C＜50%	ON	Flashing	OFF	OFF
C＜25%	Flashing	OFF	OFF	OFF

❼ Pins and GPIO used

Pin No.	Usage	Remark
2, 4	+5V power supply
6	Ground
29	GPIO5 for power management
32	GPIO12 for power management
33	GPIO13 for power management
31	GPIO6 for AC power loss detection (Jumper for PLD inserted,High=POWER loss, Low=Power supply normal)
36	GPIO16 for fan speed: HIGH => fast, LOW=> slow	New added on V1.2

❽ 18650 battery dimension

Please do not use 18650 battery with built-in protection circuit

❾ How to programming to get ASD function on V1.2 version

The following is fake C/C++ code:

while(1) {
// You need to implement getCurrentVoltage function
float fVoltage = getCurrentVoltage();
if (fVoltage <= 2.5) {
//execute shut down command, "sudo x708off"
break;
}
}

Return to X708

Add your comment

Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.

Enable comment auto-refresher

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #8
19 months ago

Score 0

I'm using the x708 ver1.2.
How to use the ASD function if it is under <= 3.0V.
I want know the step I can follow.

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Walker
19 months ago

Score 0

Hi, when battery low (≤3Vdc ), it short - Automatic shutdown, if you need Procedure to enable ASD function, you need to pay attention to the following:
1. Battery voltage must be >3Vdc
2. Insert the battery into the holder
3. Wait 3 seconds then insert the jumper
4. If the jumper inserted before battery, remove battery & jumper then repeat step 1, 2 and 3.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #15
25 months ago

Score 0

Is there any way to "turn off" the X708 when the Pi is shut down? Currently I have to press the button for a long time (7 sec) after shutdown to do this.

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
25 months ago

Score 0

Hi，

Please refer toX708-Software

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #15
25 months ago

Score 0

Hi! How do I connect a NO push button with LED to the 4 pin interface? Thank you

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
25 months ago

Score 0

Hello，

The [external power switch connector] on the board only support a momentary switch.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #16
25 months ago

Score 0

Thank you for your quick reply.

I think the pinout in this documentation is wrong. It says:

1 Power on/off control connecting to switch
2 Ground
3 LED+ for battery low indicator
4 LED+ for power on, rebooting and shutdown

But shorting pin 1 and pin 2 has no effect.

Instead, shorting pin 2 and pin 4, I get the expected behavior like Power on and force shutdown (holding >8 seconds).

I have a X708 V2.0 if that makes a difference.

I have a normally open four pin momentary switch with build in LED.
Like this one: amazon.de/gp/product/B07KCCLGXJ

1 LED +
2 LED -
3 S1
4 S2

Currently I connected S1 to pin 2 and S2 to pin 4 to make the switch working. Also I have connected LED + to pin 3 and LED - to pin 1 to make the LED working.

Even if everything works now, I wonder if everything is connected correctly?

Thank you.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
25 months ago

Score 0

Hi，

amazon.de/gp/product/B07KCCLGXJ----Operating voltage 12 Volts；

X708 UPS output is 5V

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #14
26 months ago

Score 0

What is the indication of the LED labled (HS) beside the LED labled (FAN) on the x708 v2?
It turned red the first time when I connected the ground of the Raspberry Pi with the ground of an external power supply I use to control devices that need more power. Now it is red even when the ground of the Raspberry pi is not connected to anything.
The Raspberry pi powers nothing through its 5V

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #13
25 months ago

Score 0

HS, is for High Speed. It's used by the fan.py script, when above the threshold it start spinning faster and lowered speed when temp is below threshold. Notice that x708 fan is always running at low speed.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #14
25 months ago

Score 0

Now that you mentioned it, it makes sense. Since when this happens, it is accompanied by a notable increase in the fan speed.
Thank you "Anonymous user #13" whoever you are.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #13
26 months ago

Score 0

Which GPIO pin can be used to control Case Fan x728-C1?
Is it possible to stop the x708 board fan? (not LOW but STOP)

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
25 months ago

Score 0

Hello，

1. The fan of X728-C1 case is only GND 5V ，does not controlled by GPIO.

2. You can unplug it's cable if you want to stop it.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #12
28 months ago

Score 0

Can I simultaneously connect a lithium polymer battery in xh2.54 and another lithium polymer battery in ph2.0?

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
28 months ago

Score 0

Hi，

We do not recommend this, please use the same specification of batteries.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #10
30 months ago

Score 0

Feature: GPIO16 for fan speed
Does it work on the fan that comes with the board?

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
30 months ago

Score 0

Hi，

Yes，It controls the fan of X708 V1.2 and later versions

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #10
31 months ago

Score 0

x708 v1.2. new hat. the power loss detection led is always flashing. battery is always draining and no charging. checked that raspberry usb c power supply is ok. need advice.

when running x708pld.py, it shows:
---AC Power Loss OR Power Adapter Failure---
---AC Power OK,Power Adapter OK---
---AC Power Loss OR Power Adapter Failure---
---AC Power OK,Power Adapter OK---
---AC Power Loss OR Power Adapter Failure---
---AC Power OK,Power Adapter OK---
---AC Power Loss OR Power Adapter Failure---
---AC Power OK,Power Adapter OK---
---AC Power Loss OR Power Adapter Failure---
---AC Power OK,Power Adapter OK---

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
31 months ago

Score 0

Hi，

Please remove the battery to test. Can USB-C power supply power the X708？ If OK, please re-install the battery test.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
31 months ago

Score 0

Hi，

Could you please tell us more details? especially the power supply you use. Please send a test video and tell us your order number by Emai(support@geekworm.com). thank you.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #10
30 months ago

Score 0

suspect raspberry pi usb c 5v 3a not able to supply sufficient power when setup is boot from sdd

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
30 months ago

Score 0

What is your x708 used with? If the load is large, you can try to use a higher current power supply.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #9
32 months ago

Score 0

Hi!

I can't find any script on how to set the fan speed to high/low:
"GPIO16 for fan speed: HIGH => fast, LOW=> slow" "New added on V1.2".

I don't know if it is running high or low now, but the case fan sounds as an airplane that is about to take off from my desktop.

This is unacceptable. There must be a way to turn it off when not needed and only turn it on at very high temperatures.

If there is a high and low settings too i really want to know how to change it between these two mode.

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
32 months ago

Score 0

Hello,

You can also refer to this link to adjust the fan speed：
http://www.s...oftware.html

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #8
33 months ago

Score 0

4. Power button (Script for power mgnt installed)

where can i set the code described above

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Lisa
33 months ago

Score 0

Hi，

Please refer X708-Software

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #7
36 months ago

Score 0

Hi. I have just purchased x708v1.2. How do i get on ASD function? The Step 9 is not detailed enough and i need a step-by-step solution. Where do i put the code? In Terminal? How do you have the script run automatically after starting up?

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #3
50 months ago

Score 0

I can't get the x708 to shut down with the momentary switch any ideas how to do this?

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #4
49 months ago

Score 0

I am having the same problem. The pld python script also does not detect when I unplug AC power. I'm running on a raspberry pi 4 (2018 model) with 4gb of ram. And I used the latest full version of raspberry pi is from today October 24th 2020.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #5
49 months ago

Score 0

I added sudo in front of /etc/x728pwr.sh & in /etc/rc.local and now the momentary switch seems to be working as expected. Also note that the pin descriptions under section 3 above are incorrect. Pin 1 is the NO pin of your momentary switch, Pin 2 is ground or common for the switch, pin 3 is ground for the LED in the switch and pin 4 is +V for the LED in the switch. Pin 1 is the farthest pin from the fan.

I found out that the pin to let the Pi know if AC power is good or not was not working on the female side of the header that goes directly to the pi. I get between 0.2 and 1.0 ish volts. If i measure the male side that would go to another hat i get 0v when AC power is on and 3.4v when AC power is off. Looking into how to fix that. But if I use jumper wires and use the male pin the x728pld.py script works correctly.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #5
49 months ago

Score 0

Did some poking around and the pin for the female side PLD was not soldered well. I soldered it using a soldering iron and the problem with the PLD was resolved, so I resoldered every pin on both sides of the board. Looks like along with poor documentation Geekworm also has some quality control problems.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Xiali
48 months ago

Score 0

Hi dear ,please refer to X708-Software

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #2
50 months ago

Score 0

RPi CPU cooling fan never seems to stop running. Is there something I can do to have it only activate when the Pi needs cooling? Cheers

Permalink | Reply

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #5
49 months ago

Score 0

Directly on the X708 no, the fan is connected directly to power. You could setup a mosfet and use a GPIO pin to toggle if the fan is on or not though.

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #6
48 months ago

Score 0

I would be interested to understand how to modify my set-up so that the fan comes under a GIPO pin as it is running constantly and that is painful on my poor ears

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #11
28 months ago

Score 0

The fan in the case is probably connected to 5 V without regulation. I connected it to the 3.3V pin of the Raspi. Now it's quiet!

Permalink

You are ignoring the author of this comment
Show comment | Manage ignore list

Anonymous user #1
50 months ago

Score 0

Hi,
Can we please get some documentation of which GPIO pins do what, and under which conditions?
Thanks

Permalink | Reply

Difference between revisions of "X708-Hardware"

Latest revision as of 17:04, 1 March 2024

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools

In other languages

WIKI