Difference between revisions of "PiKVM"
Line 50: | Line 50: | ||
** 1 x USB-A to USB-C OTG Cable (Cable Length: 100cm / 39.37 inch) | ** 1 x USB-A to USB-C OTG Cable (Cable Length: 100cm / 39.37 inch) | ||
** 4 x F/F M2.5*20 Spacers | ** 4 x F/F M2.5*20 Spacers | ||
− | ** | + | ** 8 x M2.5*5 Screws |
** 1 x M2.5*10 Screws | ** 1 x M2.5*10 Screws | ||
*'''1 x X630-A5 V1.0 Adapter Board''' | *'''1 x X630-A5 V1.0 Adapter Board''' |
Revision as of 19:46, 25 June 2022
Contents
Overview
PiKVM (https://pikvm.org/) is a very powerful and Open Source Software which allows for a remote connection via your Raspberry Pi to turn on/off or restart your computer, configure the UEFI/BIOS, and even reinstall the OS using the Virtual CD-ROM or Flash Drive. You can use your remote keyboard and mouse or PiKVM can simulate a keyboard, mouse, and a monitor, which are then presented in a web browser as if you were working on a remote system directly. It's true hardware-level access with no dependency on any remote ports, protocols or services!
The KVM refers to Keyboard Video Mouse. The PiKVM kit is designed and based on Raspberry Pi 4 Model B, also support Raspberry Pi 3B/3B+, but the PiKVM case will only support Raspberry Pi 4.
The PiKVM is composed of follow parts:
- X630 HDMI to CSI-2 Module (for video capture)
- X630-A3 Expansion Board (for ethernet, cooling, RTC, power in etc)
- X630-A5 Adapter Board (it will be install into the PC case to connect with computer motherboard)
- 0.96 inch OLED (for display)
- Ethernet Cable (TIA/EIA-568.B)
Features
- Designed especially for PiKVM ( Raspberry Pi based KVM over IP)
- Works with the latest Raspberry Pi 4B
- Fully compatiblie with PiKVM OS
- Control a server and computer using a web browser
- HDMI Full HD capture based on the TC358743 chip
- OTG Keyboard & mouse; Mass Storage Drive emulation
- Hardware Real Time Clock (RTC) with CR1220 coin battery socket
- Equipped with cooling fan that allows the heat from your Raspberry Pi to dissipate
- Equipped with solidstate relays to protect RPi GPIO pins from computer and ESD spikes
- ATX control via RJ45 connector Switch the machine on or off, reset it, and monitor the status of HDD LED & power LED remotely
- Reserves the 10pin SH1.0 connector for future I2S HDMI audio support
- Reserves the 4pin header & spacers for I2C OLED display
- Reserves the 40pin header that can be stacked with other Raspberry Pi accessory boards
How to Power PiKVM
- Power Input: 5.1Vdc +/-5% , ≥3A (Power Via USB Type-C port of X630-A3)
Packing List
- 1 x 0.96 inch OLED:Resolution: 128×64 pixel, with 2 piece of M2*6 screws
- 1 x Ethernet Cable (Cable length: 100cm)
- 1 x X630 HDMI to CSI-2 Module
- 1 x FPC Cable(5cm length)
- 1 x X630-A3 V1.2 Expansion Board
- 1 x USB-A to USB-C OTG Cable (Cable Length: 100cm / 39.37 inch)
- 4 x F/F M2.5*20 Spacers
- 8 x M2.5*5 Screws
- 1 x M2.5*10 Screws
- 1 x X630-A5 V1.0 Adapter Board
- 1 x M3.5*6 Screw
- 4 x 2pin Female to Female Dupont Cables (Cable Length: 47cm / 18.50 inch)
User Manual
Hardware Parameters
Wiring Diagram
Note:
- The X630-A5 adapter board will be install into the PC Case.
- The wire group ① connect to X630-A5 comes from the PANEL of PC Case.
- The black and red wires(wire group ②) come from X630-A5 accessories.
Wiring of computer front panel IO socket
(Use ASUS for example, different computers maybe different)
Enable comment auto-refresher
Anonymous user #14
Permalink |
Walker
Anonymous user #13
Permalink |
Walker
Anonymous user #12
Permalink |
Anonymous user #12
Walker
Anonymous user #11
Permalink |
Walker
Anonymous user #10
Permalink |
Walker
Anonymous user #9
Permalink |
Walker
Anonymous user #8
Permalink |
Lisa
Anonymous user #7
Permalink |
Lisa
Anonymous user #6
Permalink |
Lisa
Anonymous user #8
Lisa
Anonymous user #5
Permalink |
Lisa
Anonymous user #4
Permalink |
Lisa
Anonymous user #3
Permalink |
Harry
Anonymous user #2
Permalink |
Lisa
Anonymous user #1
Permalink |
Lisa