XScript
This is script installation tutorial for NASPi, NASPi Gemini 2.5, NASPi CM4-M2 and NASPi CM4-2.5
This script also works on bookworm OS, and test it on Jan. 9th 2024.
The original key pwm fan control script is from pimlie/geekworm-x-c1, pimlie implements the pwm fan shell script, which does not depend on third-party python libraries at all. Thanks to pimlie.
Now we think you have successfully flashed the OS Image into Micro SD and and power on the device, and you have also completed the operations such as creating new user required in some Raspberry Pi OS.
After your system boots, then you need to open Terminal
prpgram, then type the following command to complete the installation of the script
[NOTE]: The current script supports ubuntu 23.04.
OS that has been tested
- Raspbian
- DietPi
- Manjaro
- Ubuntu (Testing based on Ubuntu 23.04)
- myNode
- Umbrel
- Volumio
- RetroPie
- Twister
Note: Not tested with Home Assistant, for some reason, we are not able to upgrade and use the Home Assistant to test, please pay attention to check if there is any update in the future.(If you have successfully tested Home Assistant, welcome to share your experience via email at: support@geekworm.com)
Preconfigured config.txt
To install pwm fan, first add dtoverlay=pwm-2chan
to /boot/firmware/config.txt
under [all] or the end of file and reboot
:
sudo nano /boot/firmware/config.txt
Save & exit.
sudo reboot
Download the script
git clone https://github.com/geekworm-com/xscript cd xscript chmod +x *.sh
PS: For some OS such as Raspberry Pi OS Lite, the git tool is not installed by default, if you get an error like error: -bash: git: command not found, please run the following command to install the git tool.
sudo apt install -y git
Create the x-c1-fan service
Note: If your device does not support pwm fans or you are not using pwm, you can skip this step
Run the following command to install fan service script;
./install-fan-service.sh
Then the pwm fan starts running.
Create the x-c1-pwr service
If you are using ubuntu verson 23.04 or more high version, please run the following command:
./install-pwr-service-ubuntu.sh
OR run the following command to install power management script;
./install-pwr-service.sh
Prepair software shutdown script
If you are using ubuntu verson 23.04 or more high version, please run the following command:
./install-sss-ubuntu.sh
OR, Run the following command to install software shutdown script (sss),
./install-sss.sh
After the installation is complete, an xoff
command will be created to shut down the software.Then you can run xoff
to execute software shutdown.
Test safe shutdown
Software safe shutdown command:
xoff
DON'T run the 'shutdown' linux command to shut down, otherwise the power of shield will not be shut down.
Hardware safe shutdown operation:
You can verify the safety switch through the onboard switch, press and hold the switch for 3
seconds, then the blue LED will flash slowly and the shutdown is going then all LEDs will be off until the device is completely powered off.
- press on-board button switch
1-2
seconds to reboot - press button switch
3
seconds to safe shutdown, - press
7-8
seconds to force shutdown.
Sample
- The code for fan speed control is now in the
x-c1-fan.sh
file. fan-rpi.py
andfan-pigpio.py
are no longer used, and are reserved here for research and use by python lovers only.
Uninstall
Run the following command to uninstall all.
./uninstall.sh
Support
Email: support@geekworm.com
If you have any problems during use, please contact us by email and tell us the product model you are using and the OS version you are using.
FAQ
Q: How to login volumio via SSH?
1. Enable SSH:
Visit http://volumio.local/dev/, then click ENABLE SSH button
2. URL connection is IP address, and the default user name is volumio, default password is volumio
Q: How to login to Umbrel via SSH?
A: ssh umbrel@umbrel.local (or ssh umbrel@Q: How to login to myNode via SSH?
A: URL connection is IP address, and the default user name is admin, default password is boltQ: How to login to DietPi via SSH?
A: URL connection is IP address, and the default user name is root, default password is dietpiQ: Is LibreELEC supported?
A: TODO
Enable comment auto-refresher
Anonymous user #24
Permalink |
Anonymous user #24
Lisa
Anonymous user #24
Permalink |
Lisa
Anonymous user #25
Anonymous user #23
Permalink |
Anonymous user #22
Permalink |
Lisa
Anonymous user #20
Permalink |
Anonymous user #21
Anonymous user #19
Permalink |
Anonymous user #18
Permalink |
Harry
Anonymous user #17
Permalink |
Harry
Anonymous user #16
Permalink |
Harry
Anonymous user #9
Permalink |
Anonymous user #9
Permalink |
Anonymous user #14
Permalink |
Anonymous user #13
Permalink |
Walker
Anonymous user #11
Permalink |
Anonymous user #11
Walker
Anonymous user #14
Anonymous user #10
Permalink |
Walker
Anonymous user #9
Permalink |
Anonymous user #9
Walker
Anonymous user #8
Permalink |
Walker
Anonymous user #15
Anonymous user #7
Permalink |
Anonymous user #7
Walker
Anonymous user #6
Permalink |
Harry
Anonymous user #5
Permalink |
Harry
Anonymous user #4
Permalink |
Walker
Anonymous user #12
Anonymous user #3
Permalink |
Harry
Anonymous user #3
Permalink |
Harry
Anonymous user #2
Permalink |
Harry
Anonymous user #2
Anonymous user #2
Anonymous user #1
Permalink |
Harry