222
edits
Changes
Jump to navigation
Jump to search
QQ3. How to disable/enable the 5V output of the UPS when the RPi 5 is turned off?
QQ4: How to disable '''auto power on''' feature on [[X1200]]?
QQ5: How to disable '''auto power on''' feature on [[X1201]]?
QQ6: How to disable '''auto power on''' feature on [[X1202]]?
QQ7: How to disable '''auto power on''' feature on [[X1203]]?
QQ8: Why is the RPi5 LED still on and red after the UPS is turned off?
QQ9: What battery is recommended for this ups UPS shield?
if If using a battery packor battery holder, please make sure it is a parallel battery pack. '''Please use a high-quality battery holder with thick and durable connection cables. Using a low-quality battery holder with thin or poorly connected wires may cause the X1203 to malfunction or fail to operate as expected.'''
QQ10: Run <code>sudo i2cdetect -y 1</code>, can't find I2C address 0x36?
QQ11. How do you disable the X1202 auto-shutdown when you use it standalone (not installed on a RPi5)?
QQ12. X1203 UPS voltage drops / low voltage warning appears?
QQ13. Documentation about the I2C registers：
no edit summary
</div>
<div class="mw-collapsible-content">
A:Regarding the low voltage warning issue(Please refer to Q1 to check whether the connection is installed correctly):
* Please carefully check whether your hardware installation is secure and if the pogo pins are making proper contact. We have had cases where customers found that loose brass standoffs caused poor contact with the pogo pins, leading to the low voltage warning.
* It may be caused by an OS update. Please confirm whether you have recently updated the OS or if your OS system updates automatically.
* Please run the command:<code>vcgencmd pmic_read_adc</code> and provide us with the result. Alternatively, use a multimeter to measure the voltage value of '''PIN2'''. As shown in the figure
[[File:X120x.png|700px]]
<pre>
pi@geekworm:~ $ vcgencmd pmic_read_adc
3V7_WL_SW_A current(0)=0.00097593A
3V3_SYS_A current(1)=0.13955800A
1V8_SYS_A current(2)=0.25374180A
DDR_VDD2_A current(3)=0.01854267A
DDR_VDDQ_A current(4)=0.00049020A
1V1_SYS_A current(5)=0.25276590A
0V8_SW_A current(6)=0.34547920A
VDD_CORE_A current(7)=0.87514000A
3V3_DAC_A current(17)=0.00024420A
3V3_ADC_A current(18)=0.00024420A
0V8_AON_A current(16)=0.00341880A
HDMI_A current(22)=0.02063490A
3V7_WL_SW_V volt(8)=3.70534400V
3V3_SYS_V volt(9)=3.31467300V
1V8_SYS_V volt(10)=1.80024200V
DDR_VDD2_V volt(11)=1.11355200V
DDR_VDDQ_V volt(12)=0.60109830V
1V1_SYS_V volt(13)=1.10622600V
0V8_SW_V volt(14)=0.80109810V
VDD_CORE_V volt(15)=0.72017020V
3V3_DAC_V volt(20)=3.31318300V
3V3_ADC_V volt(21)=3.31684600V
0V8_AON_V volt(19)=0.80029220V
HDMI_V volt(23)=5.19920000V
EXT5V_V volt(24)=5.20322000V
BATT_V volt(25)=0.00000000V
</pre>
Please check the voltage value of <mark>EXT5V_V</mark> line
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
If using a lithium battery, the required voltage is 3.7V;
There are 2 XH2.54-2P battery connectors on board, it is recommended to use the same type of battery.
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
[https://www.analog.com/media/en/technical-documentation/data-sheets/MAX17040-MAX17041.pdf MAX17040G+]
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q14. Why does the RPI 5 lose power within a few seconds after pressing the power button on the X120x UPS?
</div>
<div class="mw-collapsible-content">
A:
'''Please note: If the UPS does not detect the RPi5, it will automatically shut down within 3 seconds. So you need to install the RPi 5 on the UPS and make sure that the RPi5 has good contact with the UPS's pogo pins.'''
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q15. Which product should I choose if I can’t connect to a Raspberry Pi via pogo pins?
</div>
<div class="mw-collapsible-content">
A:
For the X12-UPS series, we recommend the '''[[X1206]]''' – models from X1200 to X1205 do not support this usage. The X120- UPS series auto-powers off when no Raspberry Pi 5 is detected, while the X1206 can be set to "Always Power On" mode and keeps working even if the Raspberry Pi is shut down. Please refer to <span style="color:red">'''Interface ⑩_ALON'''</span> in the picture.
[[File:X1206-IMG-7240-Interface-New.jpg|800px]]
You can also consider the '''[[X-UPS1]]'''. It features a GPIO Pin-Connected standalone design with high flexibility for installation and adaptation (refer to the picture).
[[File:X-UPS1-IMG-5409.jpg|800px]]
</div>
</div>