5,771
edits
Changes
Jump to navigation
Jump to search
==Features==
{| class="wikitable"
|-
| '''For use with''' ||
Raspberry Pi 5 Only
|-
| '''Key Features''' ||
'''UPS Output'''
* Provides continuous operation for up to 10 hours (duration depends on battery type and applications)
* Supports a maximum current output of '''5.1V 6000mA''', suitable for most Raspberry Pi applications
* Integrated Advanced Power MOSFET with an equivalent of 7mΩ RDS(ON) to minimize power loss
* Convenient pogo pin connection for powering the Pi, eliminating the need for cabling and soldering
* Equipped with XH2.54 connectors and two USB sockets for 5V power output (Share 6000mA current output)
'''Battery Charging'''
* Supports fast battery charging with a upto 3000mA current
* Battery charging control can be managed via GPIO
* Provides protection against battery overcurrent and overvoltage
* '''Built-in protection against reverse''' connection of battery cells
* Integrated Maxim's fuel-gauge systems for reading battery voltage and percentage over i2c
* On-board LEDs indicate battery charging and discharging levels of 25%, 50%, 75%, and 100%
* Features a 4-cell 21700 battery holder, supporting up to 20,000mAh with four 21700 batteries
'''Power Input'''
* Integrated high-efficiency step-down DC-DC converter
* Wide operating input range of 9V to 18V, strongly recommen [[PSU60 | Geekworm 12V 5V Power supply]]
* Up to 95% efficiency for optimal power conversion
<!--* Provides up to 5.5A output current, enabling 3A fast charging while powering the system-->
* The power supply with DC jack can get up to 10A input current, which can achieve 3A fast charging while powering the system. Of course, this also depends on the DC power adapter you use. A good quality power adapter is very important.
* Allows power input from various sources such as a car, solder panel, and more
* Common power input jack size of 5.5x2.1mm
* '''No longer provides TYPE-C charging port'''
'''Power Management'''
* Seamless power switching between backup power and power adapter
* On-board push button performs the same actions as the '''RPi 5''''s power button
* Automatically cuts off power when the Pi is shut down
* On-board LED indicates power status and Pi detection
* AC power loss and power adapter failure detection via GPIO
* Auto power-on when power is applied or restored
* Automatic safe shutdown when battery voltage is low (programmable)
* Ultra-low standby power consumption to maximize battery life
* Advanced system power-path management to minimize frequent charging and discharging of batteries
'''Misc'''
* Connects to the Pi via convenient pogo pins, eliminating the need for additional cabling
* Designed to be attached on the bottom, allowing the use of favorite HATs alongside it
* XH2.54 connector available for adding your own power button
|-
| '''Spec''' ||
<span style="color:red">'''Power input:''' 5Vdc 5A via USB Type-C of X1202; or 6-18Vdc, ≥3A via DC 5521 power jack of X1202</span>
'''UPS output:''' 5.1V ±5% Max 5A
'''Battery charging current:''' Max 2.3-3.2A
'''Terminal Battery Voltage:''' 4.23V
'''Battery Recharge Threshold:''' 4.1V
'''Ports & Connectors:'''
* DC power jack - 5.5x2.1mm
* DC6-18V power input connector x1 - XH2.54-2P
* USB Type-C socket x1
* 18650 battery socket x4
* 5V Power output connector x2 - XH2.54 2-pin
* USB2.0 type-A power output socket x2
* External power button connector x1 - XH2.54-2P
'''PCB Size:''' 97.4mm x 85mm
|-
|'''Power Supply Tips''' ||
* The Wide 6-18V Input allows the user to choose the power supply flexibly. The required current is greater than or equal to 2A/3A.
* The reserved 6-18V XH2.54 connector provide convenient power supply when integrate X1202 with other products.
* The X1202's Type-C port simplifies power supply by supporting the 5V 5A Type-C power adapter used by the Raspberry Pi 5.
* Please note that the DC 6V-18V wide voltage connector is just for the convenience of using the power supply you have on hand. If you have a Raspberry Pi 5 power supply, you don’t need to buy an additional power supply. Just use it to charge the X1202.
|-
| '''Notes''' ||
* <span style="color:red">Do not apply power to your Raspberry Pi 5 via the Type-C USB socket.</span>
* Do not use 18650 battery with built-in protection circuit.
|}
==Packing List==