3,191
edits
Changes
Jump to navigation
Jump to search
X630
,{{GD Template Impl}}
[[File:X630-IMG-2673.jpg|thumb|right|X630 HDMI TO csi-2]]
[[File:X630-IMG-2671.jpg|thumb|right|X630 HDMI TO csi-2]]
[[File:X630-IMG-2669.jpg|thumb|right|X630 HDMI TO csi-2]]
[[File:X630-a2-IMG-3258.jpg|thumb|right|X630-A2 Shield]]
[[File:X630-a2-IMG-3270.jpg|thumb|right|X630-A2 + X630 assembly]]
[[File:X630-a2-IMG-3266.jpg|thumb|right|X630-A2 + X630 + X630-C1 assembly]]
[[File:X630-C1-IMG-3000-接口示意-1.jpg|thumb|right|X630-C1 case]]
[[File:X630-pi0-IMG-3177.jpg|thumb|right|X630 + Pi zero]]
[[File:X630-pi0-IMG-3178-case.jpg|thumb|right|X630 + Pi zero + Case]]
==Overview==
'''[Update]''': X630 V1.5 is released on Dec. 2022;
V1.5 has the following updates based on V1.3
* Fixed HDMI back powering issue.
* Remove the software reset. (Since there is no usage scenario and the product is more complex, pikvm does not need software reset etc.)
[[File:X630-V1.5-VS-X630-V1.3.jpg|500px|none|X630 V1.5 vs X630 V1.3]]
The X630 hdmi to csi module is a bridge module that converts HDMI stream to MIPI CSI-2, which enables your Raspberry Pi to accept HDMI video and audio streams and process them as incoming data source.
[[File:X630-diagram.png|X630 HDMI to CSI-2 diagram|600px]]
{{HDMI to CSI}}
==Features==
* Specifically designed mounting hole for the Raspberry Pi
* HDMI to CSI-2 bridge chip: Toshiba TC358743XBG
* Video Formats Support (Up to 1080P)
* CSI-2 Transmit Interface MIPI CSI-2 compliant (Version 1.01 Revision 0.04 -2 April 2009)
* CSI-2 connector: 15 pin FPC with 1.0 mm pitch
* Able to start RASPISTILL or RASPIVID multiple times and no reboot required
* Easily fixed on Raspberry Pi and DIY your pefect case
* Support work with [[X1300-A2]] accessory board capture HDMI audio via I2S
==X630-A2==
X630-A2 is an accessory board that provides audio functions when used with X630. It also has a 3007 fan onboard and also supports [[X630-C1]] case.
X630-A2 GPIO Use
{| class="wikitable"
! Rpi GPIO !! PIN NAME !! Description !! Note
|-
| 5 || HDET || HDMI input detect (high level ) || 3.3V
|-
| 6 || INT || Interrupt Output signal – active high (Level) || 3.3V
|-
| 12 || RST || TC358743XBG reset control , active high || 3.3V
|-
| 18 || A_SCK || I2S/TDM Bit Clock signal (BCK) || 3.3V
|-
| 19 || A_WFS || I2S Word Clock or TDM Frame Sync signal (LRCK) || 3.3V
|-
| 20 || A_SD || I2S/TDM data signal (Data) || 3.3V
|}
==User Manual==
===Hardware & Software===
* [[X630-Hardware]]
* [[X630-Software]]
===Application===
* Application: https://qengineering.eu/install-gstreamer-1.18-on-raspberry-pi-4.html
===Chip Information===
* Chip Information-'''EN''': [[File:TC358743XBG_datasheet_en_20171026.pdf|none|HDMI TO CSI-2 Chip-EN]]
* Chip Information-'''CN''': [[File:TC358743XBG_datasheet_zh_cn_20151218.pdf|none|HDMI TO CSI-2 Chip-CN]]
===X630 3D File===
* X630 3D file: [[File:X630-asm.stp]]
===X630 PCB dimention===
[[File:X630-PCB.png|700px]]
==Packing List==
===X630 Packing List===
* 1x X630 HDMI to CSI-2 Module
* 1x X630-A1 Board
* 1 x 5cm Length 5pin 1.0mm FPC cable (for Pi 4B / 3B+ / 3B / 2B)
* 1 x 8cm Length 15Pin 1.0mm to 22pin 0.5mm FPC cable (for Pi Zero / Zero W / Zero 2W)
* 2 x F/F M2.5*17mm Spacer
* 4 x M2.5*6 Screw
* 1 x M2.5 Nut
[[File:X630-Packing-List.jpg|500px]]
===X630-A2 Packing List===
* 1 * X630-A2 Audio Hat & Cooling Fan Expansion Board
* 1 * 10-pin Cable
* 4 * F/F M2.5*12 Spacers
* 8* M2.5*5+5 Screws
==Match Metal Case==
[[X630-C1]] is the matching case for X630 and X630-A2, But we no longer produce, you can refer to the following 3D drawings if you need: [[File:X630-c1-asm.zip]] or [[File:X630-c1-asm.stp]]
==Installation==
===Installation Video===
X630+X630-A2+X630-C1 Case for Raspberry Pi 4: https://youtu.be/lJL2Ihs1aYg
{{#ev:youtube|https://youtu.be/lJL2Ihs1aYg}}
===How to install X630 & X630-A2 & X630-C1===
[[File:X630安装图-2000x2000.jpg|800px|How to install X630]]
<HR/>
[[File:X630+X630-A1Installation.jpg|800px| How to install X630/X630-A2/X630-C1]]
==FAQ==
'''Notes & Known Issues'''
First, we recommend that you read [https://www.raspberrypi.org/app/uploads/2013/07/RaspiCam-Documentation.pdf Raspberry Pi camera applications document]
(1) If using GStreamer or PiKVM, please change to Hardware reset mode. Otherwise, the X630 won't be detected and there will be no video.
(2) An accessory board (X630-A2) for audio capturing & reset is available now.
(3) Currently the software reset mode can only support RASPISTILL or RASPIVID.
(4) If GStreamer is installed in Raspberry Pi OS, RASPISTILL & RASPIVID are no longer worked.
Q: How Do I Know if My Raspberry Pi Camera is Working? (X630 is actually a CAMERA device)
A: Refer to https://raspberrytips.com/troubleshooting-camera-module/
Q: What to do if there is no video output?
A: 1. When use the PI-KVM, please set the dip switches at the back of X630 to HW mode(Hardware reset mode). Pull the HW switch to 1 and pull the SW switch to 0.(Our default mode is HW mode.)
Please set the switches at power off status. (For PiKVM usage, you will need to turn off SW reset DIP switch and turn on HW reset DIP switch prior to connecting the CSI cable to your Pi4.)
2. Software reset uses GPIO 509 to reset operation through GPIO. Please refer to wiki: [[X630-Software]]
Q: Which connector model is compatible with 10pin functional connector?
A: It is SH1.0 10Pin connector.
Q: Does the X630 support to work with Octoprint?
A: No, the X630 is not tested with Octoprint. It is recommended to choose hardware reset to test and ensure that the video input by X630 must be 1080p or 720p, which cannot be converted higher than 1080P.
Q: 1080p 60Hz HDMI to CSI-2 via TC358743 ?
A: Please refer to: https://forums.raspberrypi.com/viewtopic.php?t=211802&sid=e6fef431928907e63fc8eb539cd75389 for reference.
<!--Add review function! -->
<comments />
<!--Please choose the -->
<!--Remove other categories, just keep the appropriate categories -->
[[Category:Product Manual]]
[[Category:Raspberry pi]]
[[File:X630-IMG-2673.jpg|thumb|right|X630 HDMI TO csi-2]]
[[File:X630-IMG-2671.jpg|thumb|right|X630 HDMI TO csi-2]]
[[File:X630-IMG-2669.jpg|thumb|right|X630 HDMI TO csi-2]]
[[File:X630-a2-IMG-3258.jpg|thumb|right|X630-A2 Shield]]
[[File:X630-a2-IMG-3270.jpg|thumb|right|X630-A2 + X630 assembly]]
[[File:X630-a2-IMG-3266.jpg|thumb|right|X630-A2 + X630 + X630-C1 assembly]]
[[File:X630-C1-IMG-3000-接口示意-1.jpg|thumb|right|X630-C1 case]]
[[File:X630-pi0-IMG-3177.jpg|thumb|right|X630 + Pi zero]]
[[File:X630-pi0-IMG-3178-case.jpg|thumb|right|X630 + Pi zero + Case]]
==Overview==
'''[Update]''': X630 V1.5 is released on Dec. 2022;
V1.5 has the following updates based on V1.3
* Fixed HDMI back powering issue.
* Remove the software reset. (Since there is no usage scenario and the product is more complex, pikvm does not need software reset etc.)
[[File:X630-V1.5-VS-X630-V1.3.jpg|500px|none|X630 V1.5 vs X630 V1.3]]
The X630 hdmi to csi module is a bridge module that converts HDMI stream to MIPI CSI-2, which enables your Raspberry Pi to accept HDMI video and audio streams and process them as incoming data source.
[[File:X630-diagram.png|X630 HDMI to CSI-2 diagram|600px]]
{{HDMI to CSI}}
==Features==
* Specifically designed mounting hole for the Raspberry Pi
* HDMI to CSI-2 bridge chip: Toshiba TC358743XBG
* Video Formats Support (Up to 1080P)
* CSI-2 Transmit Interface MIPI CSI-2 compliant (Version 1.01 Revision 0.04 -2 April 2009)
* CSI-2 connector: 15 pin FPC with 1.0 mm pitch
* Able to start RASPISTILL or RASPIVID multiple times and no reboot required
* Easily fixed on Raspberry Pi and DIY your pefect case
* Support work with [[X1300-A2]] accessory board capture HDMI audio via I2S
==X630-A2==
X630-A2 is an accessory board that provides audio functions when used with X630. It also has a 3007 fan onboard and also supports [[X630-C1]] case.
X630-A2 GPIO Use
{| class="wikitable"
! Rpi GPIO !! PIN NAME !! Description !! Note
|-
| 5 || HDET || HDMI input detect (high level ) || 3.3V
|-
| 6 || INT || Interrupt Output signal – active high (Level) || 3.3V
|-
| 12 || RST || TC358743XBG reset control , active high || 3.3V
|-
| 18 || A_SCK || I2S/TDM Bit Clock signal (BCK) || 3.3V
|-
| 19 || A_WFS || I2S Word Clock or TDM Frame Sync signal (LRCK) || 3.3V
|-
| 20 || A_SD || I2S/TDM data signal (Data) || 3.3V
|}
==User Manual==
===Hardware & Software===
* [[X630-Hardware]]
* [[X630-Software]]
===Application===
* Application: https://qengineering.eu/install-gstreamer-1.18-on-raspberry-pi-4.html
===Chip Information===
* Chip Information-'''EN''': [[File:TC358743XBG_datasheet_en_20171026.pdf|none|HDMI TO CSI-2 Chip-EN]]
* Chip Information-'''CN''': [[File:TC358743XBG_datasheet_zh_cn_20151218.pdf|none|HDMI TO CSI-2 Chip-CN]]
===X630 3D File===
* X630 3D file: [[File:X630-asm.stp]]
===X630 PCB dimention===
[[File:X630-PCB.png|700px]]
==Packing List==
===X630 Packing List===
* 1x X630 HDMI to CSI-2 Module
* 1x X630-A1 Board
* 1 x 5cm Length 5pin 1.0mm FPC cable (for Pi 4B / 3B+ / 3B / 2B)
* 1 x 8cm Length 15Pin 1.0mm to 22pin 0.5mm FPC cable (for Pi Zero / Zero W / Zero 2W)
* 2 x F/F M2.5*17mm Spacer
* 4 x M2.5*6 Screw
* 1 x M2.5 Nut
[[File:X630-Packing-List.jpg|500px]]
===X630-A2 Packing List===
* 1 * X630-A2 Audio Hat & Cooling Fan Expansion Board
* 1 * 10-pin Cable
* 4 * F/F M2.5*12 Spacers
* 8* M2.5*5+5 Screws
==Match Metal Case==
[[X630-C1]] is the matching case for X630 and X630-A2, But we no longer produce, you can refer to the following 3D drawings if you need: [[File:X630-c1-asm.zip]] or [[File:X630-c1-asm.stp]]
==Installation==
===Installation Video===
X630+X630-A2+X630-C1 Case for Raspberry Pi 4: https://youtu.be/lJL2Ihs1aYg
{{#ev:youtube|https://youtu.be/lJL2Ihs1aYg}}
===How to install X630 & X630-A2 & X630-C1===
[[File:X630安装图-2000x2000.jpg|800px|How to install X630]]
<HR/>
[[File:X630+X630-A1Installation.jpg|800px| How to install X630/X630-A2/X630-C1]]
==FAQ==
'''Notes & Known Issues'''
First, we recommend that you read [https://www.raspberrypi.org/app/uploads/2013/07/RaspiCam-Documentation.pdf Raspberry Pi camera applications document]
(1) If using GStreamer or PiKVM, please change to Hardware reset mode. Otherwise, the X630 won't be detected and there will be no video.
(2) An accessory board (X630-A2) for audio capturing & reset is available now.
(3) Currently the software reset mode can only support RASPISTILL or RASPIVID.
(4) If GStreamer is installed in Raspberry Pi OS, RASPISTILL & RASPIVID are no longer worked.
Q: How Do I Know if My Raspberry Pi Camera is Working? (X630 is actually a CAMERA device)
A: Refer to https://raspberrytips.com/troubleshooting-camera-module/
Q: What to do if there is no video output?
A: 1. When use the PI-KVM, please set the dip switches at the back of X630 to HW mode(Hardware reset mode). Pull the HW switch to 1 and pull the SW switch to 0.(Our default mode is HW mode.)
Please set the switches at power off status. (For PiKVM usage, you will need to turn off SW reset DIP switch and turn on HW reset DIP switch prior to connecting the CSI cable to your Pi4.)
2. Software reset uses GPIO 509 to reset operation through GPIO. Please refer to wiki: [[X630-Software]]
Q: Which connector model is compatible with 10pin functional connector?
A: It is SH1.0 10Pin connector.
Q: Does the X630 support to work with Octoprint?
A: No, the X630 is not tested with Octoprint. It is recommended to choose hardware reset to test and ensure that the video input by X630 must be 1080p or 720p, which cannot be converted higher than 1080P.
Q: 1080p 60Hz HDMI to CSI-2 via TC358743 ?
A: Please refer to: https://forums.raspberrypi.com/viewtopic.php?t=211802&sid=e6fef431928907e63fc8eb539cd75389 for reference.
<!--Add review function! -->
<comments />
<!--Please choose the -->
<!--Remove other categories, just keep the appropriate categories -->
[[Category:Product Manual]]
[[Category:Raspberry pi]]