5,653
edits
Changes
Jump to navigation
Jump to search
Default shutdown wattage is around 1 to 1.4W. However this can be decreased by manually editing the EEPROM configuration, sudo rpi-eeprom-config -e and change the settings to:
sudo rpi-eeprom-config -e
BOOT_UART=1
POWER_OFF_ON_HALT=1
BOOT_ORDER=0xf416
To cancel a pending update run "sudo rpi-eeprom-update -r".
==压力测试工具==
* 测试工具S-Tui + Stress的使用: https://www.cnblogs.com/ChuanYangRiver/p/15132348.html
* JF的压力测试脚本: https://gist.github.com/geerlingguy/91d4736afe9321cbfc1062165188dda4 or download from [[File:Pi-cpu-stress.zip]]
* Geekworm 测试脚本：https://github.com/geekworm-com/pi-cpu-stress
* https://github.com/nschloe/stressberry
* [[Naspi stress test]]
==Sysbench工具==
* Install Sysbench on Raspberry Pi:https://lindevs.com/install-sysbench-on-raspberry-pi
==vcgencmd命令==
可以参考： https://blog.csdn.net/bona020/article/details/51373326
显示可用命令：
vcgencmd commands
vcgencmd measure_clock <clock>
显示时序, 可指定arm, core, h264, isp, v3d, uart, pwm, emmc, pixel, vec, hdmi, dpi.
vcgencmd measure_volts <id>
显示电压. id可以是core, sdram_c, sdram_i, sdram_p, 如不指定默认为core.
vcgencmd measure_temp
显示BCM2835芯片的温度.
vcgencmd codec_enabled <codec>
显示指定解码器是否可用, 解码器分别有H264, MPG2, WVC1, MPG4, MJPG, WMV9. 请注意MPG2和VC1是需要购买证书的.
vcgencmd版本
显示固件版本
[[Category:Smart Home]]
[[Category:Knowledge]]
sudo rpi-eeprom-config -e
BOOT_UART=1
POWER_OFF_ON_HALT=1
BOOT_ORDER=0xf416
To cancel a pending update run "sudo rpi-eeprom-update -r".
==压力测试工具==
* 测试工具S-Tui + Stress的使用: https://www.cnblogs.com/ChuanYangRiver/p/15132348.html
* JF的压力测试脚本: https://gist.github.com/geerlingguy/91d4736afe9321cbfc1062165188dda4 or download from [[File:Pi-cpu-stress.zip]]
* Geekworm 测试脚本：https://github.com/geekworm-com/pi-cpu-stress
* https://github.com/nschloe/stressberry
* [[Naspi stress test]]
==Sysbench工具==
* Install Sysbench on Raspberry Pi:https://lindevs.com/install-sysbench-on-raspberry-pi
==vcgencmd命令==
可以参考： https://blog.csdn.net/bona020/article/details/51373326
显示可用命令：
vcgencmd commands
vcgencmd measure_clock <clock>
显示时序, 可指定arm, core, h264, isp, v3d, uart, pwm, emmc, pixel, vec, hdmi, dpi.
vcgencmd measure_volts <id>
显示电压. id可以是core, sdram_c, sdram_i, sdram_p, 如不指定默认为core.
vcgencmd measure_temp
显示BCM2835芯片的温度.
vcgencmd codec_enabled <codec>
显示指定解码器是否可用, 解码器分别有H264, MPG2, WVC1, MPG4, MJPG, WMV9. 请注意MPG2和VC1是需要购买证书的.
vcgencmd版本
显示固件版本
[[Category:Smart Home]]
[[Category:Knowledge]]