Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 11:30, 22 January 2025 Lisa talk contribs posted a new comment on X1201 (Hi,Sorry for the wrong description, it is updated now, X1201 only support 5V.)
  • 10:17, 22 January 2025 24.211.221.158 talk posted a new comment on X1001 (Update: I ended up just returning my WD SN770 and ordering a Samsung 970 EVO Plus. It's working much better.)
  • 20:16, 21 January 2025 49.182.91.142 talk posted a new comment on X1201 (Can I supply 12v to the XH2.54 socket labeled 5v in on my x1201? The info at the top says 9-18v but then further down it says 5v..) Tags: Mobile web edit, Mobile edit
  • 18:49, 21 January 2025 192.122.132.233 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (How did you achieve such a high read/write speed? Are you using x1005 or which SSD hat?)
  • 18:46, 21 January 2025 192.122.132.233 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (I managed to make it work. But the performance I am getting might not the best. I have seen a comment here showing 900MB+ speed, but I am getting 400- MB only. Is there a way to optimize this? I set the pciex1_gen=3, and updated to the latest firmware.)
  • 13:38, 21 January 2025 211.30.159.146 talk posted a new comment on X1201 (I recently purchased the x1201 for my Pi5 and When using the “sudo i2cdetect -y 1” command I get nothing, 1 doesn’t exist for me, I can only detect 11 and 12 and they do not show the 0x36 address. I have checked all pin connections with a multimeter and they are all making good contact. What else could it be? Thanks) Tags: Mobile web edit, Mobile edit
  • 13:22, 21 January 2025 66.235.15.173 talk posted a new comment on X1202 (I was wrong. On further testing, I think the GPIO16 driven high does disable the charger and does not continue raising the battery voltage. I previously incorrectly assumed two things: 1. I thought the board design would always be running the pi5 from battery voltage. This would be a simple "dual conversion" setup. Instead, the board appears to not run the pi5 from battery voltage when sufficient input power is available, even if the charger is disabled. This is great. 2. I incorrectly...)
  • 12:03, 21 January 2025 66.235.15.173 talk posted a new comment on X1202 (For completeness, I also tried both the USB-C x1202 input, and 12V into the DC input on the x1202. This didn't make any difference; the charging continued despite driving GPIO16 high and despite the CHG LED being off. The board seems to work well aside from not turning the charging off when GPIO16 is driven high.)
  • 11:06, 21 January 2025 66.235.15.173 talk posted a new comment on X1202 (On my x1202, driving GPIO16 high, the charging LED stops blinking (so the pogo pin is making contact with HW pin 36), but the actual charging doesn't stop. I have tried with the pin set as input with both "pull up" and "pull down", and with the pin set as output and driving it high vs low. Pulled high or driven high, the CHG LED stops blinking, but ... battery volts continue increasing until ~4.15V. Overall, I'm not sure if turning the charger on and off to zig-zag near a lower voltage is a...)
  • 03:53, 21 January 2025 24.211.221.158 talk posted a new comment on X1001 (!!! Nevermind... still failing :(.)
  • 00:18, 21 January 2025 81.197.7.236 talk posted a new comment on X728-hardware (I'm using following code for shutdown: GPIO.output(GPIO_PORT, GPIO.HIGH) time.sleep(3) GPIO.output(GPIO_PORT, GPIO.LOW) I have auto power-on jumper inserted. Why do I have to cycle power twice to turn the Raspberry back on?)
  • 18:12, 20 January 2025 Lisa talk contribs posted a new comment on X1009 (X1206 UPS（5V power out） not support X1009（12V power input）.please refer to X-UPS1)
  • 18:11, 20 January 2025 Lisa talk contribs posted a new comment on X1206 (X1206 UPS（5V power out） not support X1009（12V power input）.please refer to X-UPS1)
  • 12:07, 20 January 2025 24.211.221.158 talk posted a new comment on X1001 (Thanks! This fixed random I/O errors I was experiencing with a WD_BLACK SN770 SSD and a Raspberry Pi 5. The symptoms were similar to that of "Anonymous user #20". It would boot fine but soon after some paging errors would appear in the journal and commands would fail with I/O errors (or it would just say command not found). Booted using an SD card temporarily, ran rpi-update, and booted back into the SSD. Everything works normally now.)
  • 23:53, 19 January 2025 213.125.50.74 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (I've been using a WD Blue SN580, as marked as solved in the top of this topic. Anonymous12 writes after updating eeprom it al works. For me this was NOT the case for my WD SN580. Even after upgrading to latest jan 2025 eeprom the drive does not run stable. Yes it boots now, and from time to time seems to work. But after some time you see numerous I/O errors which makes the drive completely inaccessible. It never runs for more than 24 hours, requiring a reboot for it to start working again. T...)
  • 06:08, 19 January 2025 93.234.25.123 talk posted a new comment on X1009 (Can the X1009 and the X1206 be used together with one board? If so, which of the two do you plug the power cable into?)
  • 06:08, 19 January 2025 93.234.25.123 talk posted a new comment on X1206 (Can the X1009 and the X1206 be used together with one board? If so, which of the two do you plug the power cable into?)
  • 00:52, 19 January 2025 178.25.154.48 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (Same here. Yesterday, I bought a WD Blue SN580 and it does not work with X1002 and latest firmware.)
  • 04:51, 18 January 2025 174.54.172.229 talk posted a new comment on X1001 (I had the 2TB Samsung 980 Pro working great until I added a pi 5 cooler. After that it no longer recognized the drive. Blue light stays on, but no boot and lspci shows nothing connected. Put the drive in a usb enclosure and it boots fine from that. Very confused why this is. I guess I'll try another drive soon.)
  • 15:57, 17 January 2025 194.88.96.84 talk posted a new comment on X728 (Having followed your advice in reply to #73, the battery capacity. Only goes up to 80% and then once it reaches this it begins to drop! I also have an X1202 and the same batteries but this goes up to 100% and takes 10-12 hours to discharge. The x728 with the same batteries is taking only 1-2 hours from 80% (max it seems to go to) to discharge to 0.) Tags: Mobile web edit, Mobile edit
  • 03:32, 17 January 2025 81.56.119.189 talk posted a new comment on WEMOS ESP32 Board with 18650 Battery Holder (The documents are useless are they are generic about the chips and there is no schematic for this specific board model. Anyways if anybody needs, the only way is via voltage divider to ADC pin (GPIO32 to 39) using two 100K Ohm resistors... the voltage can be calculated using the formula: (readAnalog(pin) / 4095) * 3.3 * 2 (also adding a fixed value to calibrate the result is suggested, based on measurements with multimeter))
  • 19:26, 16 January 2025 31.173.21.207 talk posted a new comment on KVM-A3 (do you resolve issue ? i have the same..)
  • 15:21, 14 January 2025 Harry talk contribs posted a new comment on X1201 (This error occurs when Python cannot find the PyQt5 module. It usually happens if PyQt5 is not installed or if the Python interpreter is not correctly configured. '''Solution''' '''1. Install PyQt5''' Ensure that PyQt5 is installed using pip. Open your terminal or command prompt and run: <pre>pip install PyQt5</pre> '''2. Verify Installation''' Check if PyQt5 is installed correctly by running: <pre>pip show PyQt5</pre> This command will display the installation details of PyQt5, inclu...)
  • 15:20, 14 January 2025 Harry talk contribs deleted comment #5470 on X1201
  • 15:20, 14 January 2025 Harry talk contribs posted a new comment on X1201 (This error occurs when Python cannot find the PyQt5 module. It usually happens if PyQt5 is not installed or if the Python interpreter is not correctly configured. '''Solution''' '''1. Install PyQt5''' Ensure that PyQt5 is installed using pip. Open your terminal or command prompt and run: pip install PyQt5 '''2. Verify Installation''' Check if PyQt5 is installed correctly by running: pip show PyQt5 This command will display the installation details of PyQt5, including the path where it...)
  • 15:20, 14 January 2025 Harry talk contribs deleted comment #5469 on X1201
  • 15:20, 14 January 2025 Harry talk contribs posted a new comment on X1201 (This error occurs when Python cannot find the PyQt5 module. It usually happens if PyQt5 is not installed or if the Python interpreter is not correctly configured. '''Solution''' '''1. Install PyQt5''' Ensure that PyQt5 is installed using pip. Open your terminal or command prompt and run: pip install PyQt5 '''2. Verify Installation''' Check if PyQt5 is installed correctly by running: pip show PyQt5 This command will display the installation details of PyQt5, including the path where it i...)
  • 15:13, 14 January 2025 Harry talk contribs posted a new comment on NASPi Gemini 2.5 (Weird question. The fan script has nothing to do with whether the SSD is recognized. What OS are you using?)
  • 12:13, 14 January 2025 Lisa talk contribs posted a new comment on X1200 (please refer to：[https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1200 Software])
  • 12:08, 14 January 2025 Lisa talk contribs posted a new comment on X728 (Hi,There is a learning process for the IC to read the power level, please try to fully charge and then discharge it a few times and it will remember the process.)
  • 12:02, 14 January 2025 Lisa talk contribs posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (Hi,please contact us by email <support@geekworm.com> and please note your order ID,thank you.)
  • 12:00, 14 January 2025 Lisa talk contribs posted a new comment on X306 (Don't support that. Only one 18650 battery can be installed.)
  • 11:59, 14 January 2025 Lisa talk contribs posted a new comment on X306 (4pin header：solder it yourself if needed. 1. Shorting AL and ON will automatically power on 2. GND and PSW are pins for external reset/momentary switch)
  • 11:46, 14 January 2025 Lisa talk contribs posted a new comment on X-UPS1 (Please refer to X-UPS1#PCB Dimension above)
  • 11:40, 14 January 2025 Lisa talk contribs posted a new comment on X820 (Hi,please contact us by email <support@geekworm.com> and please note your order ID,thank you.)
  • 11:35, 14 January 2025 Lisa talk contribs posted a new comment on WEMOS ESP32 Board with 18650 Battery Holder (Hello,We no longer sell this product and this page will no longer be maintained. you can get support on the official website.[https://www.espressif.com/en/support/download/documents Official documents])
  • 11:34, 14 January 2025 Lisa talk contribs deleted comment #5459 on WEMOS ESP32 Board with 18650 Battery Holder
  • 11:34, 14 January 2025 Lisa talk contribs posted a new comment on WEMOS ESP32 Board with 18650 Battery Holder (Hello,We no longer sell this product and this page will no longer be maintained. you can get support on the official website.Official documents https://www.espressif.com/en/support/documents/technical-documents)
  • 11:32, 14 January 2025 Lisa talk contribs deleted comment #5458 on WEMOS ESP32 Board with 18650 Battery Holder
  • 11:31, 14 January 2025 Lisa talk contribs posted a new comment on WEMOS ESP32 Board with 18650 Battery Holder (Hello,We no longer sell this product and this page will no longer be maintained. you can get support on the official website.https://www.espressif.com/en/support/documents/technical-documents)
  • 18:12, 13 January 2025 80.11.191.233 talk posted a new comment on CSI Manual on Pi 5 (Issue solved. On Raspberry Pi 5 with Media controller API 6.6.62, the C779 MIPI CSI-2-TX must be connected on the CAM/DISP 1 port as specified from the device tree. Afterwards, a proper EDID file must be loaded on the properly created subdev to be visible by the HDMI-TX source. Example: v4l2-ctl -d /dev/v4l-subdev2 --set-edid=file=edid.txt --fix-edid-checksums)
  • 13:49, 13 January 2025 73.70.118.131 talk posted a new comment on X306 (Turn off with external button? Pins 3&4 per specs. Short press does switch on, long press does not switch off. Is there any changes that need to be made?)
  • 01:47, 13 January 2025 194.88.96.79 talk posted a new comment on X728 (Can you help me understand why brand new batteries (Panasonic 3400mah) 18650 (4 of them, 2 in the extra battery pack with the case) are showing no more than 90% capacity. The same batteries in the x1202 case with a Raspberry pi5 are showing 99/100% capacity. They share the same source of power which has well in excess of what’s needed. Just wondering if there’s a calibration needed or some other settings to get the number correct.) Tags: Mobile web edit, Mobile edit
  • 17:45, 12 January 2025 73.70.118.131 talk posted a new comment on X306 (Can a 2nd 18650 battery be added in parallel for longer run time?)
  • 10:57, 12 January 2025 180.129.86.113 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (I still cannot get my WD Blue SN580 to get working. I followed all steps. - Installed bookworm raspbian on SD card (system boots) - enable PCIe in /boot/firmware/config.txt via adding dtparam=pciex1_gen=3 - eeprom is updated to the latest 2024 Nov version Nothing was working up to this point. Then I edited the eeprom settings via ``` sudo rpi-eeprom-config --edit ``` and added PCIE_PROBE=1. Still nothing is working, i don't see anything in `dmesg` output or in `lspci`. However, both LEDs on...)
  • 09:43, 12 January 2025 186.77.199.44 talk posted a new comment on X1200 (Greetings, I have purchased X1200 and I would like to know how I can monitor the battery voltage from the rasbia os system itself.)
  • 03:54, 12 January 2025 109.245.196.202 talk posted a new comment on X-UPS1 (Hello, where can I find the dimensions specified in millimeters?)
  • 02:01, 12 January 2025 93.170.44.59 talk posted a new comment on X820 (There was an accident with the X820. The IVR P307H chip burned out. It is located next to the auto on/off jumpers. Please tell me what kind of chip it is and how to replace it.)
  • 09:00, 11 January 2025 81.56.119.189 talk posted a new comment on WEMOS ESP32 Board with 18650 Battery Holder (It seems that in this model there is a battery charging system for the integrated battery but no ADC pin are connected to measure the charge... how is it possible? Any way to get battery level through an analogread() of GPIO pin?)
  • 03:12, 11 January 2025 75.28.21.198 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (For Raspbian Bookworm (the most recent) you should be able to just add the following to your config.txt: dtoverlay=vc4-kms-dpi-panel,mzp280,rotate=270 dtoverlay=spi0-0cs dtoverlay=ads7846,penirq=27,xmin=200,xmax=3850,ymin=200,ymax=3850 The first dtoverlay to add vc4-kms-dpi-panel is required to bring up the display itself and requires us to also enable vc4-kms-v3d (which I think is the default now anyway). The second dtoverlay allows us to use the SPI bus without a CS pin (which is taken cu...)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"