Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 17:48, 31 July 2024 Lisa talk contribs posted a new comment on P575 (Hi, P575 is a fully enclosed case, only the built-in fan can be installed.)
  • 17:15, 31 July 2024 83.242.66.85 talk posted a new comment on P575 (Nice case, but it seems that the fan is not properly used there. I'm bit worried, that the fan is almost useless there, since it is only blowing off air from inside of the case, and not through the case fins. There should be a fan like in P511-A, or the original RPi Fan shield, blowing air THROUGH the case fins, this means PARALLEL to the case, and not perpendicular to it. Do you agree?)
  • 09:59, 31 July 2024 Lisa talk contribs posted a new comment on X1203 (Hello，yes you can use them at the same time, but please use batteries of the same type.)
  • 21:34, 30 July 2024 175.116.49.141 talk posted a new comment on X1203 (Can both battery charging locations, each with an xh2.54-2p connector, on this board be used simultaneously?)
  • 15:14, 30 July 2024 Lisa talk contribs posted a new comment on P573 (Hello,please refer to P575; and you can buy it from here:https://geekworm.com/products/p575)
  • 20:41, 29 July 2024 131.200.252.16 talk posted a new comment on P573 (Hell. Will you plan to release this full case with additional fan, like the P511-A?)
  • 15:47, 29 July 2024 Lisa talk contribs posted a new comment on X306 (Hello,Not recommended.the pogo pins need to touch the Pi zero 2W.)
  • 15:41, 29 July 2024 Lisa talk contribs posted a new comment on P580 (Hello,We haven't tested it yet, but if the Pimoroni Duo base has the same dimensions and mounting hole positions as the Pimoroni base, it should work with the P580 case.)
  • 15:06, 29 July 2024 Lisa talk contribs posted a new comment on X1001 (Hi，It is not supported to be disabled, you can cover it with insulating tape.)
  • 09:54, 28 July 2024 76.107.164.7 talk posted a new comment on X1001 (Is there a way to dissable the blue activity LED on this board?)
  • 00:56, 28 July 2024 82.1.230.96 talk posted a new comment on P580 (Hi, I see both cases support the Pimoroni base. Would your cases work with Pimoroni Duo base? Thanks!)
  • 14:31, 27 July 2024 173.239.254.15 talk posted a new comment on X306 (Hello, is it possible to solder a wire directly to the pogo pins and then connect the wires to the pi unit and solder if needed for a project?) Tags: Mobile web edit, Mobile edit
  • 10:41, 26 July 2024 Lisa talk contribs deleted comment #4967 on NASPi
  • 10:40, 26 July 2024 Lisa talk contribs posted a new comment on NASPi (Hello,friend; rpi5 version 2.5" SATA HDD board: please refer to X1100, X1100#Matching_Case)
  • 10:40, 26 July 2024 Lisa talk contribs posted a new comment on NASPi (Hello,friend; rpi5 version 2.5" SATA HDD board: please refer to X1100, X1100#Matching_Case)
  • 10:40, 26 July 2024 Lisa talk contribs deleted comment #4966 on NASPi
  • 10:39, 26 July 2024 Lisa talk contribs posted a new comment on NASPi (Hello,friend; rpi5 version 2.5" SATA HDD board: please refer to X1100, X1100#Matching_Case)
  • 10:38, 26 July 2024 Lisa talk contribs deleted comment #4965 on NASPi
  • 10:38, 26 July 2024 Lisa talk contribs posted a new comment on NASPi (Hello,friend; 2.5 inch SATA HDD expansion board: please refer to X1100, X1100#Matching_Case)
  • 10:34, 26 July 2024 Lisa talk contribs posted a new comment on P511 (Hello,friend;Sorry for the inconvenience, could you please contact us by email[info@geekworm.com] and please tell us your order number. Thank you.)
  • 04:59, 26 July 2024 176.111.180.182 talk posted a new comment on P511 (dual-fan version (P511-B) fans are not working and not detecting in settings :()
  • 11:07, 25 July 2024 185.180.13.99 talk posted a new comment on NASPi (Will there be rpi5 version with a pcie FPC connection with in case?)
  • 00:21, 25 July 2024 147.231.72.217 talk posted a new comment on X728 (Hello, it looks there is no way to meaningfully use X728 without scritps for software shutdown. If you power loss happens to RPI without scripts the power to RPI will remain until the butteries are completely discharged or RPI breaks because of repeating reboot on low input voltage. There is on standalone UPS behavior (confirmed by email from support).)
  • 10:17, 24 July 2024 Lisa talk contribs posted a new comment on X728 (Hi,please refer to X728-hardware#6-Pin Function Header for X728 V1.2)
  • 21:08, 23 July 2024 76.155.2.74 talk posted a new comment on X728 (Hi, what are the jumpers next to the USB-C power in for on the 1.2v board? There are 6 pins vs 4 on the newer versions?)
  • 18:34, 23 July 2024 Harry talk contribs posted a new comment on X1203 (bat.py is the example you want)
  • 18:26, 23 July 2024 Lisa talk contribs posted a new comment on X1202 (Hello,please refer to X1202 HardwareGPIO16 function.and you need to write a script to do this yourself.)
  • 22:58, 22 July 2024 192.77.184.26 talk posted a new comment on X1202 (Can the full charge voltage be adjusted via script or configuration code? It isn't good for LiIon batteries to sit fully charged for extended periods. Ideally they would charge to ~3.9-4V while retaining the option of charging to 4.2V Can you set PSU_MAX_CURRENT=3000 instead of 5000 to draw less Amps from power supply while charging? Could you set it to 2000?)
  • 12:06, 22 July 2024 Lisa talk contribs posted a new comment on X301 (Hello,X301 has a SATA SSD interface, no sata cable required.)
  • 06:33, 22 July 2024 73.189.109.33 talk posted a new comment on X301 (How does the X301 connect to SATA drives? Is there a place to plug in a SATA cable? Or are you recommending that a USB to SATA adapter cable be used?)
  • 20:25, 20 July 2024 175.116.49.141 talk posted a new comment on X1203 (Pogo pin position modification fixed the issue. Thanks. Can you create and distribute a script that automatically shuts down when the power is low, similar to the x708 board?)
  • 18:28, 20 July 2024 Lisa talk contribs posted a new comment on X1203 (Hello,please refer to FAQ[Run sudo i2cdetect -y 1, can't find I2C address 0x36?]; Please check the [pogo pin]，you can adjust the [pogo pin] position.)
  • 18:23, 20 July 2024 Lisa talk contribs posted a new comment on X728-hardware (Hi,please email us [info@geekworm.com]；We will answer your questions via email.thank you.)
  • 18:04, 20 July 2024 175.116.49.141 talk posted a new comment on X1203 (I recently purchased two X1203 boards and one X1202 board for testing purposes. I'm encountering an issue with the X1203 boards - neither of them is being recognized via I2C. However, the X1202 board I bought is working fine and is detected without any problems. I've double-checked the connections and tried cleaning the GPIO pins, but the X1203 boards still aren't showing up when I run i2cdetect.)
  • 01:02, 20 July 2024 147.231.72.217 talk posted a new comment on X728-hardware (Hello, I plan to use X728 v 2.5 to overcome problems with quite often (several per month) AC power outage for some minutes. I expect X728 will supply power in these situation. But what will happen if the power outage is longer and voltage on battery goes under 3V? I am not sure I would be able to install x728 software to catch safe shutdown. I need similar behavior as with no X728. Hard power off and power on when AC is back again to let RPI boot and operate again. The location is remote an...)
  • 12:36, 18 July 2024 Lisa talk contribs posted a new comment on X306 (Hi,Thanks for your feedback, it is recommended to use a high quality power supply. Poor quality power supplies can cause damage to the UPS board.)
  • 19:38, 17 July 2024 159.224.160.123 talk posted a new comment on X306 (FYI The issue was in the power supply. Though the sound comes from the board, using a 10W power supply from Apple solves the problem. Connecting the board to the DC source eliminates sound too.)
  • 18:23, 17 July 2024 Lisa talk contribs posted a new comment on X1202 (Yes. You can do this via script, just implement a timer in the script. You can also refer to other users' feedback X1200#comment-4845, Hope it helps you.)
  • 02:28, 17 July 2024 24.170.98.57 talk posted a new comment on X1001 (oh well, so much for this)
  • 18:43, 16 July 2024 176.200.80.175 talk posted a new comment on X1202 (Yes, we know that it can be turned off with the external switch but since the Raspberry Pi is installed in an inconvenient position and is used as a dash in the car that connects to the ECU to display its data, we would like it to turn off on its own after a certain time that the power was turned off. Since X1202 communicates when there is no more power, on this event you could start a countdown, close open applications and turn off the system, without using a keyboard, mouse and external swi...)
  • 18:31, 16 July 2024 Harry talk contribs posted a new comment on X1001 (Are you saying X1011 or X1001? It's probably related to the SSD you're using.)
  • 10:02, 16 July 2024 24.170.98.57 talk posted a new comment on X1001 (using latest firmware)
  • 09:57, 16 July 2024 24.170.98.57 talk posted a new comment on X1001 (Using x1011 with samsung evo 990 2tb LSPCI no indication of phison controller; system works fine until accessing(reading) large file or running dd if=./TestingFile of=/dev/zero bs=100M count=10 oflag=dsync a couple of times... pciegen 3 is disabled by raspi-boot and on /firmware/boot.txt only have dtparam=pciex1 So far every reduced disk access works fine but again streaming a large file or performing dd will eventually freeze machine, please explaing what i should be looking for in lo...)
  • 16:10, 15 July 2024 Lisa talk contribs posted a new comment on NASPi 3.5 (Hi，LED blue indicator indicates each drive status.)
  • 16:06, 15 July 2024 Lisa talk contribs posted a new comment on X1202 (Hi，On-board push button performs the same actions as the Pi's power button. Turn off X1202 and pi5 at the same time by using an external switch)
  • 15:39, 15 July 2024 Lisa talk contribs posted a new comment on X-UPS1 (Hi，single board to output both 5V and 12V simultaneously. Provides dual 12Vdc & 5Vdc or single 5Vdc output.)
  • 21:04, 13 July 2024 223.25.71.8 talk posted a new comment on NASPi 3.5 (My 2 blue LEDs are flashing, may I know what does it mean?)
  • 20:47, 13 July 2024 185.21.248.71 talk posted a new comment on X1202 (hi, how can I close all applications and turn off the Raspberry pi after 5 minutes after the external power supply has been turned off?? I don't want to drain the batteries to make it shut down)
  • 14:57, 13 July 2024 175.116.49.141 talk posted a new comment on X-UPS1 (Is it possible for one of the boards in a stacked configuration to output 5V while the other board outputs 12V, or for a single board to output both 5V and 12V simultaneously?)
  • 16:10, 11 July 2024 Lisa talk contribs posted a new comment on X1200 (Hi,please contact us by email[info@geekworm.com],and please let us know your order No.;thank you.)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"