X880

From Geekworm Wiki
Jump to navigation Jump to search

X880 Packing List
X880 A1 A2 Packing List
X880+X880 A1 A2

Overview

This X880 USB 3 to dual SATA Gen3 ports shield makes it easy to add high-capacity, high-performance external data storage to your Raspberry Pi 4.The dual SATA shield supports two 2.5" or 3.5" SATA hard drives with ultra-fast data transfer speeds and configurable RAID modes. This dual SATA shield delivers fast file transfer rates up to 5Gbps with USB 3.1 Gen 1 performance. It supports SATA I, II and III and is enhanced with UASP to maximize the performance and speed of your SATA III drives. The dual SATA shield provides an effective solution for Raspberry Pi 4 to store, access, back up, and protect important files.

NOTE:

  1. We do not recommend using Samsung hard drives,Please use hard drives of other brands.
  2. Not supported for use with the X735 Power Management Board.

Features

  • Ideal storage solution for Raspberry Pi 4 - Dual SATA Gen3 ports Shield
  • Create high performance storage with a dual SATA HDD RAID array through USB 3.1 (5Gbps)
  • Supports Standard Desktop 2.5"/3.5" SATA Hard Drives or SSD
  • Supports hard drives up to 10TB
  • Supports SATA I, II and III and is enhanced with UASP to maximize the performance and speed of your SATA III drives
  • Supports Transfer Speeds up to 5Gbps (USB 3.0),480Mbps (USB 2.0), 12Mbps (USB 1.1)
  • Supports hardware JBOD, RAID0(striping), RAID1(mirror), Normal mode
  • Supports mode select via jumper setting
  • Plug-and-play, no drivers needed
  • Powers the Raspberry Pi 4 via test pins - Only one PSU required
  • Specially-made USB3.1 jumper to connect with RaspberryPi - no additional cables needed
  • LED blue indicator indicates each drive status
  • Mounting holes and standoffs provide mechanicalstability of the RaspberryPi and X880 assembly
  • Heat dissipation solution:We recommend use embedded radiator P165-A or P165-B
  • Supports installation of X880-A1 A2 2.5 "/ 3.5" SATA SSD/HDD Shield

Power Supply Requirement

  • Power supply: 12Vdc +/-5% , ≥3A
  • Ports & Connectors: DC jack - 5.5x2.5mm

Packing List

X880:

  • 1 x X880 V1.1 Dual SATA Gen3 HDD Shield
  • 1 x USB connector
  • 2 x Jumper link Pitch 2.54mm
  • 6 x M2.5 *4mm Screws
  • 2 x M2.5 *8+3mm Spacers
  • 2 x M2.5 *8mm Spacers

X880 A1 A2:

  • 1 x X880-A1 2.5 "/ 3.5" SATA SSD/HDD Shield
  • 1 x X880-A2 2.5 "/ 3.5" SATA SSD/HDD Shield
  • 2 x SATA 7+15pin male to female HDD power extension cable(20.5cm and 15.0cm)
  • 4 x M2.5 *10mm Screws
  • 12 x M3 *6mm Screws
  • 4 x M3 *18+6mm Spacers
  • 4 x M3 *18mm Spacers

User Manual

FAQ

Q: Does the X880 work on Raspberry Pi 3 B+/3B?

A: Sorry, the X880 does not support Raspberry Pi 3 B+/3B.

Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


Anonymous user #31

14 months ago
Score 0++

Hi.

Is there a firmware update that would allow the X880 to show each drive's fixed identifier?

This data seems to be hidden by the Micron controller.

Each boot generates a new RANDOM ID for the attached drives in the format "scsi-SJMicron_Tech_RANDOM__<48 bit HEX string>".

$ls -lh /dev/disk/by-id/ total 0 lrwxrwxrwx 1 root root 9 Jan 7 09:05 scsi-SJMicron_Tech_RANDOM__16C75493717C -> ../../sda

lrwxrwxrwx 1 root root 9 Jan 7 09:05 scsi-SJMicron_Tech_RANDOM__BA16C7549371 -> ../../sdb

Anonymous user #32

14 months ago
Score 0++
Micron does not control this content, it may be related to the OS you are using

Anonymous user #30

17 months ago
Score 0++
Hello. How i can make online diagnostic RAID 1 system? For example had online information about problem at RAID 1. Thanks.

Lisa

17 months ago
Score 0++
Hi,It depends on the system you use. Maybe you can find the answer on google.Thanks~

Anonymous user #29

17 months ago
Score 0++

Hi, if I want to have a clear RAID is it necessary to make any RAID changes once I set up the X880 and install HDDs? I do not want to format the drives or lose any data! IF clear RAID is default I guess all should work fine without formating the HDDs??

Thnx

Lisa

17 months ago
Score 0++

Hi,

Yes, you can use the CLEAR RAID mode (PM, factory default setup) and not format the hdds.Plese back up your data to avoid unexpected situations.Thanks.

Anonymous user #28

19 months ago
Score 0++
Is there a safe way to shut down? I know the idea of a NAS is to he on 24/7 but sometimes you just need to turn it off. I use OMV on Debian and I tried sudo shutdown -r now and it goes the the shutdown process but the drives never power down even after 10 minutes. It feels wrong to just pull the plug on a spinning drive.

Lisa

19 months ago
Score 0++

Hello,

Sorry,X880 does not support software safe shutdown.

Anonymous user #26

19 months ago
Score 0++

Hi, I've a problem connecting a 3,5 disk of 8TB Toshiba N300 NAS, the X880 blue led flashes but not boot the raspberry pi I only see this error in screen: EXT4-fs error (device sda2): __ext4_find_entry:1614: inode #1426: comm systemd-udevd: reading directory lblock 0

I have other 480GB SSD connected and this works properly I only have problem with the other.

Any idea why it doesn't boot with that drive?

Lisa

19 months ago
Score 0++

Hello,

Did you test with only one hard drive(3,5 disk of 8TB Toshiba N300 NAS) connected? What power supply are you using?

Anonymous user #27

19 months ago
Score 0++
I have connected two disks, first one a 2,5 480GB SSD in which I've installed Raspberry Pi OS Lite (32-bit) and second one 3,5 disk of 8TB Toshiba N300 NAS, I'm supplying a power of DC 12v 5A charger. If only connect the first one boots okay, the problem comes when I connect both disks, the Pi doesn't works not boot. I was thinking if is there a limitation on the size of the disk? I'm using a CLEAR RAID. Any suggestion?

Lisa

19 months ago
Score 0++

Please use the same type of hard drive,HDD+HDD or SSD+SSD; an error will be reported when using SSD+HDD. If only 3.5inch disk of 8TB Toshiba is connected, do not connect other hard drives, can it boot normally?

PS:It is recommended to use an SD card to install the system.

Anonymous user #25

21 months ago
Score 0++

1) Are 2 HDD/SSD required or can I connect only 1 HDD/SSD?

2) will your recommended PSU support 2x10TB HDD?

Lisa

21 months ago
Score 0++

Hi,

1)you can use only 1HDD. 2)you can buy a 12V 5A PSU fromeGeekworm store:[[1]]

Anonymous user #24

23 months ago
Score 0++
Why are Samsung drives not recommended, what is the reason behind it and what is someone to do if they only have Samsung drives?

Lisa

22 months ago
Score 0++

Hello,

Not recommend to use SAMSUNG SSD, as there will be EMC interference.But it may vary from individual to individual, if you only have Samsung hard drives, you can test it.

Anonymous user #23

23 months ago
Score 0++
Does the X880 work with Raspberry Pi Zero 2 W

Lisa

22 months ago
Score 0++

Hi,

X880 board not support Raspberry Pi Zero 2 W

Anonymous user #22

23 months ago
Score 0++
Is it possible to add additional FAN into X880-C1+X880+X880-A1-A2 on the right side of X880-C1 for HDD? Is there any additional FAN connector for this?

Lisa

23 months ago
Score 0++

Hello,

We did not reserve fan mounting holes on the side, but you can DIY install a fan, the fan cable can be connected to the 5V out of the X880 board.

Anonymous user #21

24 months ago
Score 0++
x880 automatically puts disks to sleep when idle? I have a problem because NAS HDD drives park the head every 5 minutes. When connected directly to the raspberry pi via USB, they work without falling asleep.

Lisa

24 months ago
Score 0++

Hi,

It will go to sleep when there is no data to read or write, which can greatly protect the HDD.

Anonymous user #21

24 months ago
Score 0++

NAS disks do not like being turned on and off. This works to the detriment of NAS disks and significantly shortens the performance. NAS drives are designed to work 24/7. I found a solution to this problem - it should be added to CRON

  • / 4 * * * * root hdparm -C / dev / sdX
There was no information about it when buying - in this case, I would not buy the X880

Lisa

24 months ago
Score 0++
The x880 defaults to 5 minutes of standby, but you can change that. If you need help, please contact us [support@geekworm.com].

Harry

24 months ago
Score 0++

Hi,

We don't really recommend you to do this, because it will shorten the life of the hard drive. If you still insist, you can cancel the 5-minute hibernation by upgrading the firmware, please contact email: felix@suptronics.com

Anonymous user #20

26 months ago
Score 0++
I just purchased this item, is there a PWM cooling solution such as the X735 that is compatible with this?

Lisa

26 months ago
Score 0++

Hi

Sorry,there are currently no power management boards or PWM fan that support x880.

Anonymous user #19

26 months ago
Score 0++
What are the power ratings for 12V OUT and 5V OUT ports?

Lisa

26 months ago
Score 0++

Hi,

12V OUT -- depends on the power supply you use; 5V OUT -- total output is 5A (shared with motherboard and HDD)

Anonymous user #18

27 months ago
Score 0++

Hello Geekworm, If I'm running RAID-1 and I replace one of the drives. How do I know when the RAID rebuilding is completed? Do I need to wait until the rebuilding is completed before writing?

Thank You

Lisa

27 months ago
Score 0++

Hello,

If you replace the hard drive, please reset the RAID.

Anonymous user #18

27 months ago
Score 0++

Hello Lisa, This is a comment on your answer to "Anonymous user #18"s question. So, the one good drive isn't mirroring back to the drive which replace the failed one within the RAID controller? This is the premise of RAID-1, replacing failed drives without loosing any data. What good is RAID-1 if the failed drive can't be replaced without resetting the RAID?

Thank You

Lisa

27 months ago
Score 0++

Hi,

X880 board only provides hardware support. RAID-1 mode is to write double data. When replacing a failed hard disk, please back up the data of the other HDD. And you need to reset RAID-1 , but the recovery of data depends on your software operation. So please back up the data on the HDD.

Anonymous user #15

27 months ago
Score 0++
How is the procedure to replace a failing drive? To turn off the X880 and replace the bad driver?

Lisa

27 months ago
Score 0++

Hello,

Yes,please turn off the x880 before replacing the driver.

Anonymous user #17

27 months ago
Score 0++

Hello,

how does the board indicate that a hard drive is broken? by the changing color led or in what some other way? thank you!

Lisa

27 months ago
Score 0++
Hello,If the HDD indicator does not light up or the HDD cannot be recognized, it may be a hard disk failure and you can test the hard disk separately.

Anonymous user #16

27 months ago
Score 0++

Hi!

I´ve two 3TB 3.5" HDD and I don´t want RAID. I want bothh separately. How can I do that?

Lisa

27 months ago
Score 0++
Hi,you can use PM mode directly, no need to set RAID mode

Anonymous user #15

28 months ago
Score 0++
How is the process of replacing a broken driver under RAID 1 mode? Does it support hot-swapping?

Lisa

28 months ago
Score 0++
Hi,It does not support hot-swapping.

Anonymous user #15

28 months ago
Score 0++
Is the Raspberry required for it to work? Or can the X880 board be used standalone and be connected to other computers through USB 3.0?

Lisa

28 months ago
Score 0++
Hi,YES, the X880 board be used standalone

Anonymous user #14

29 months ago
Score 0++
Is it possible to have two 3.5 inch hdd?

Lisa

29 months ago
Score 0++
Hi,x880 can support two 3.5 inch SATA HDD

Anonymous user #13

29 months ago
Score 0++
Where can I purchase the X880-A1 and X880-A2 boards? I bought the X880 on Ali Express, but I cannot find these accessories for mounting the drives.

Lisa

29 months ago
Score 0++
Hi,X880-A1 / A2 is out in stock. and we are not sure about its delivery date yet.

Anonymous user #12

29 months ago
Score 0++
Any chance of developing enclosure for X880 in 2021?

Lisa

29 months ago
Score 0++
Hello,We are also considering designing a case for x880, but we are not sure about the time.

Anonymous user #11

30 months ago
Score 0++
Did anyone designed some 3d case plans for this that could share?

Anonymous user #10

31 months ago
Score 0++

Bonjour,

peut on booter le RPI4, sur les disques SSD ?

Lisa

31 months ago
Score 0++
Hello,Yes, it can be started from ssd ;please refer to:X825 FAQ

Anonymous user #8

32 months ago
Score 0++
Q: Can two X880s (one per USB 3.0 port) be used to add four total drives to a single Raspberry Pi?

Anonymous user #9

32 months ago
Score 0++
Hi, x880 not support that

Anonymous user #7

33 months ago
Score 0++
Hi, My I Know XH 2.54 12 V & 5 V output how many A?

Lisa

33 months ago
Score 0++
Hi, 5 V output : MAX 5.5A ; 12v output: depend on the power supply .

Anonymous user #6

33 months ago
Score 0++
Hi, you could put 2 hdd of 2.5 vertically directly on the plate, Thanks

Lisa

33 months ago
Score 0++
Hi, No, you need to use SATA 7+15pin male to female HDD power extension cable

Anonymous user #4

33 months ago
Score 0++
Hi Is the limit of 10 TB absolute, or is it theoretically possible to use larger disks, such as 16 or 18 TB?

Lisa

33 months ago
Score 0++
Hi,The SSD capacity is no limit, but to avoid insufficient power supply, you need to provide better power.

Anonymous user #5

33 months ago
Score 0++
Hi, I have a problem with my 4TB hard drive which doesn't work when connected to the board. Do any of you know solution to my problem?

Lisa

33 months ago
Score 0++
Hi,Do you set the RAID setup and Jumper?would you please tell us more information so that we can better understand the problem. please email us, you will get faster help. Thanks!support@geekworm.com

Anonymous user #4

33 months ago
Score 0++
I am also interested in a case for the X880 A1 A2, I currently have plans to use it as a NAS, possibly also as a mail server.

Lisa

33 months ago
Score 0++
Hi,Thanks for your feedback, we will consider it.Please follow our website. Best regards

Anonymous user #3

33 months ago
Score 0++

Will there eventually become a case available for the X880? I think you are doing a great job at making beautiful cases so I really hope that there will be one for this product as well. Even if it's just a 3D model dat would be awesome.

Keep up the good work!

Lisa

33 months ago
Score 0++

Hello,Thanks for your support, we are also considering and collecting more users' needs, whether to make a shell for x880. But it is still unknown. If it is possible, we will publish it on the wiki immediately.

Best regards

Anonymous user #2

33 months ago
Score 0++
when i restart my raspberrypi,the x880 blue LED switched off,and the system cannot recognize the HDDs, reboot or reconnection the power are both not working,what happened

Lisa

33 months ago
Score 0++
Hello,Please test according to【About Raid setup】. If the problem is still not resolved, please tell us your order number and email us.

Anonymous user #1

35 months ago
Score 0++
Does it work on Pi 3 B+?

Cindy

35 months ago
Score 0++
Hi, sorry, the X880 does not work on Pi 3B+/3B.