1,823
edits
Changes
Jump to navigation
Jump to search
'''AMAZON JP''': https://www.amazon.co.jp/dp/B07MTC5YPR
Customer Video 1: https==Features==* Operating System:All Raspberry Pi operating systems* Supports up to 4TB 2.5-inch SATA hard disk drives (HDD) /solid-state drive (SSD)* USB 3.1 Gen1 to SATA 6Gb/youtus Bridge Controller * USB 2.be0 connectivity offers plug-and-play functionality on your Raspberry Pi 3B+/oYQWG9MPuY03B * Quick file transfer with high-speed USB 3.0 connectivity from a PC or a Mac * Powers the Raspberry Pi - no additional power supply for RPi * Duplicated Raspberry Pi HDMI port
Customer Video 2: https://youtu.be/IGxRA_JgoRc
==Overview==* The X820 expansion board provides a complete storage solution for raspberry pi, only 2.5 inch SATA interface HDD/SDD hard disk is suitable for X820 Board;* For Use With: Raspberry Pi 3 Model B/ 2B / B+* Upgraded to USB3.1 Gen1 port; (SupportS USB 3.0) w/ high quality USB 3.0 Cable ( Lenght- 80cm/2.62inch; Diameter- 5.96mm/0.19inch)* Operating System: All Raspberry Pi operating systems* Support boot from USB mass storage device, '''USB mass storage boot is available on Raspberry Pi 3B, 3B+, 3A+, and 2B v1.2 onlyV3.0 Upgrade Features''' please refer to [[#How to boot from a USB Mass storage device on a raspberry pi 3]]:
==V3.0 Upgrade Features==
* Use upgrade Main control chip to solve the problem that the 'reboot' command is not supported in the V1.3 function.
* The HDMI adapter has been removed, which reduces the difficulty of installation; it also facilitates the design and installation of the accessory enclosure;
==Diagram of X820 V3.0==
[[File:X820-v3.0 DWG.jpg]]
'''Please use <span style="color:red;font-weight:bold">Important Note: Please use high quality DC 5V 4A power supply</span>, otherwise the best choice is to buy the DC 5V 4A power supply that Geekworm provided. If you get low quality power supply to use, it may probably will damage your 2.5 inch HDD/SSD.</span>'''HDD may not be identified or be damaged!!!
==Notice==* DO NOT APPLY POWER TO YOUR RASPBERRY PI VIA THE PI's MICRO USB SOCKET![[File:IMG-5927-power.jpg|500px]]
* 1 x 2 Pin Power Connection Wire(Cable: 10cm)
* 1 x HDMI Adapter
Q: With a hard drive installed, could you eleminate the need for a micro sd card and boot straight from drive?* Please refer to the "How to boot from a USB Mass storage device on a raspberry pi 3" below. Q: What to do if the X820 board could not detect the HDD or SSD?* (1) At first, please use the high quality power supply adapter, the hard disk will not be recognized if you use the low quality power supply, as the current of this power supply is not enough.* (2) Please run 'lsusb' command under linux terminal, and save the screenshot of the result, then send it to our email: support@geekworm.com, then we will figure out your problem together.* (3) Please remember to send us your '''order number and the website''' you ordered to us when you contact us for the X820 problem by email: support@geekworm.com.Thank you! Q: What is a recommended HDD for this board?'''
Q: How to do if I don't like the blue light on the power switch?* It is ok to disable the blue light on the power switch, you just need to pull out the white cable. Please refer to the picture.<gallery>Turn-off-led-IMG-20181108-095055.jpg|Caption1 </gallery>''Q: Why can't boot from the SSD or HDD?'''
* Theoretically it can work with 6tb or 8tb as wellFor more questions, please refer to blog '''[https://geekworm. But actually we do not test the com/blogs/raspberry-pi/faq-of-raspberry-pi-x820-v3-0-usb-3-0-2-5-sata-hdd-ssd-storage-expansion-board FAQ of Raspberry Pi X820 board with 6tb or 8tb V3.0 USB 3.0 2.5" SATA HDD, hope to get your understanding! Q: What is the pinout for the PWR Switch?/SSD Storage Expansion Board]'''
A==User Guide=====Installation Video===Geekworm Video (Pi 3 + X820 V3.0+X735+X820 Case): Please refer to herehttps: [[PH2//youtu.0 Conector Specification]]be/I1nnjh9HvGI
Q: Does the Customer Video 1 (Pi 3 + X820 Power off switch work when the Pi is powered by USB (or PoEV3.0)?: https://youtu.be/oYQWG9MPuY0
A: The Customer Video 2 (Pi 3 + X820 Power off switch cannot work when the Pi is powered by USB (or PoEV3.0): https://youtu.be/IGxRA_JgoRc
QCustomer Video 3 (Pi 3 + X820 V3.0): Where can I buy this product?* Please visit our [https://geekwormyoutu.combe/collections/bestJsrjKcfi1mg ===Installation Guide(V3.0 Version)===[[File:V3.0 Installation Guide-sellings/products/raspberryw800.jpg]] [[File:IMG-pi4511-x820-2-5-inch-sata-storage-board-dc-5v-4a-power-supply-metal-case-kit Geekworm official store1.jpg]]
For more questions, please refer to blog '''[https://geekworm.com/blogs/raspberry-pi/faq-of-raspberry-pi-x820-v3-0-usb-3-0-2-5-sata-hdd-ssd-storage-expansion-board FAQ of Raspberry Pi X820 V3.0 USB 3.0 2.5" SATA HDD/SSD Storage Expansion Board]'''
==Customer Video==1. Guide from our friends: https://youtuwww.youtube.becom/JsrjKcfi1mgwatch?v=GxNKpuhVsX8
2===Some Tips===*[[Properly Mount USB Storage on Raspberry Pi]]*[[Auto Mount an NTFS USB Drive on Raspberry Pi]]* Chinese User Manual: [[File:X820-V3.https://youtu0Guide-CN.be/IGxRA_JgoRcpdf]]
==Document==
Chinese User Manual: [[File:X820-V3.0Guide-CN.pdf]]
X820
,no edit summary
{{GD Template Impl}}
[[File:X820-V3.0-IMG-4498.jpg|thumb|right|x820 v3X820 V3.0 version raspberry pi sdd/hdd storage board- Front]][[File:X820-V3.0-IMG-4501.jpg|thumb|right|x820 v3X820 V3.0 version raspberry pi sdd/hdd storage board- Rear]][[File:X820-v3.0 DWG.jpg|thumb|right|Diagram of X820 V3.0-]][[File:IMG-4511-1.jpg|thumb|right|x820 v3X820 V3.0 version raspberry pi sdd/hdd storage board]][[File:X820-V3.0-IMG-24337909.jpg|thumb|right|x820 V1X820 V3.3 raspberry pi sdd/hdd storage board0+X735]][[File:X820-V3.0-IMG-24325929.jpg|thumb|right|x820 V1X820 V3.3 raspberry pi sdd/hdd storage board0+X735]][[File:MetailX820-caseV3.0-IMG-30507906.jpg|thumb|right|Metal Case X820 V1V3.3 or X800 SSD Storage expansion board0+X735]][[File:MetailX820-caseV3.0-IMG-30497911.jpg|thumb|right|Metal X820-C6 Case Inner View]][[File:X820 -IMG-2433.jpg|thumb|right|x820 V1.3 or X800 SSD Storage expansion board]]
==Note==
Please send your issue information with <span style="color:red;font-weight:bold">order numbers and purchase link</span> to our support email: support@geekworm.com if you need after-sale support, that will do great help to solve the problem quickly, thanks in advance.
'''What do you need to use make the X820 work?'''* A Raspberry Pi board(Pi 3B+, 3B, 2B, B+)* A X820 V3.0 2.5 inch SATA Storage Board?(this product)* A 2.5 inch SATA hard disk drives (HDD) or solid-state drive (SSD)* A Power Adapter (Power requirement are different epending on the product used, please refer to [[X820#How to Power]])* A X820 Metal Case (Optional)* A X735 Expansion Board (Optional，provide function like cooling fan, safe shutdown)
Note:# A Raspberry Pi X820 board(Pi 3B+, 3B, 2B, B+)# A DC 5V 4A Power Supply (Please use high quality power supply)# A 2.5 inch SATA does not limit the thickness of the hard disk drives (HDD) or solid-state drive (SSD)# A X820 V3.0 use Metal Case Kit(optional), but the <span style="color:red;font-weight:bold">Note: 1. when using our X820 metal case, the Max. compatible supports a hard disk thickness of the 2max.5" SATA SSD/HDD is 10.4mm/0.41inch</span>. (The stander 2.5" SATA SSD/HDD is 9.2mm/0.36inch). 2. # USB mass storage boot is available on Raspberry Pi 3B, 3B+, 3A+, and 2B v1.2 only.</span>
'''USB mass storage device boot'''
Please refer to https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md
==Installation VideoOverview==Geekworm Video: https:The X820 expansion board provides a complete storage solution for Raspberry Pi 3 Model B+ /3B /youtu2B / B+, only 2.be5 inch SATA interface HDD/I1nnjh9HvGISDD hard disk is suitable for X820 Board;
* Using patch process to improve the quality of the X820 V3.0 Board;
* Add Powers On-board powers button switch on the board to for power control the power supply.
* Add upgraded external 5V 2A power output USB port for external device such as cellphone and other device, of course. User can power the raspberry pi via this USB port when GPIO pins are occupied by other expansion board.
* User can directly use the X820 V3.0 board as a mobile hard disk even if you don't power it (tested; with our USB3.0 cable or use a good quality and relatively short USB3.0 cable); PS: In the V1.3 version, you need to power the X820 at the same time as when you use the X820 V1.3 board as a mobile Hard disk;
* Two kinds of power supply modes are supported; One of mode is that power the raspberry pi via 2 pin cable by connecting to GPIO2 (5V) and GPIO3(GND) pins, the other one of mode is power the raspberry pi via USB port; PS: DON'T USE THE TWO KIND MODES AT THE SAME TIME;
==FeaturesHow to Power=='''Use X820 Board only:'''* Supports upto 4TB 2DC 5V/4A with 5.5x2.1mm Jack '''Use X820 + X735 V3.0:'''* DC 6-30V with 5-inch SATA hard disk drives .5x2.1mm Jack(HDDrefer to [[PSU60]]) / solidto power via X735 DC port; or USB-state drive C 5V ≥3A(SSDrefer to [[PSU20]]) (Theoretically it can work with 6TB or 8TB as wellto power via X735 USB-C port '''Use X820 + X735 V2. But actually we do not test the X820 board with 6tb or 8tb HDD5, you can have a tryV2.)* Ideal storage solution for Raspberry Pi * USB 31, V2.1 Gen1 to SATA 6Gb/s Bridge Controller * USB 20, V1.0 connectivity offers plug-and-play functionality on your Raspberry Pi :'''* Quick file transfer DC 5V with high-speed USB 35.5x2.0 connectivity from a PC 5mm Jack to power via X735 DC port; or a Mac * External Self Powered USB- Do not require C 5V ≥3A(refer to [[PSU20]]) to power from Raspberry Pi via X735 USB -C port * Powers the Raspberry Pi - no additional power supply for RPi * Duplicated Raspberry Pi HDMI portNote:
<span style==Specification==* Power supply"color: AC 100 - 240V input 50 / 60Hz, 5V DC 4A output* DC red>Power Plug Size : 5requirment is different depends on different kits.5*2.5mm* Output Ports: 1 x HDMI, 1 x USB , 1 x DC jack</span>
==Packing List==
* 1 x X820 Expansion Board
* 1 x USB 3to Micro USB Power Cable (Length:14.5cm / 5.0 cable 71inch)* 1 x 2 Pin Power Connection Wire (Length: 80cm10cm / 23.62 inch93inch)
* 1 x USB connector
* 1 x Install Screws pack
==Some TipsMatching Metal Case==*[[Properly Mount USB Storage on Raspberry Pi]]*[[Auto Mount an NTFS USB Drive on Raspberry Pi]] ==Installation Guide(V3.0 Version)==[[File:V3.0 Installation Guide-w800.jpg]] Video Guide from our friends: https://www.youtube.com/watch?v=GxNKpuhVsX8 == Pictures==<gallery>X820-IMG-2437.jpg|x820-IMG-2439-1.jpg|</gallery> == Matching Metal Case for X820 V3.0 Version (Recommend)===
Please refer to [[X820 Metal Case V3.0 Version]]
== Matching Metal =Case for X820 V1.3 Version(off production)===
Please refer to [[X820 Metal Case V1.3 Version]]
==FAQ==
'''Q:Does the X820 support Trim?'''* The X820 does not support TRIM,the current X820 version only UASP supported. For LINUX and USB2.0, UASP is better. '''Q: Don't detect HDD/SDD?'''
*This is a complicated question, but we can check it from these points. Please refer to '''[[How to check the X820]]'''
'''Q: Do i With a hard drive installed, could you eleminate the need an external power source supplying for x820 boarda micro sd card and boot straight from drive?'''* Yes, here is the specification: 5V and 4A with Please refer to [[#How to boot from a USB Mass storage device on a 5.5mm barrel connector.raspberry pi 3]]
* Basically it can support all the 2.5-inch HDD with SATA 2 or STATA 3 interface.
* Customer Feedback 1: I have followed the same steps you provided and my ssd is not able to boot. I have tried again with a normal sata hard drive and it works fine. My original ssd (Patriot Burst 240gb) draws too much power. Thus, do not boot.
'''Q:Can you stack the module with itself? is the usb cable and bridge crossover?'''
*Theoretically, you can stack the X820 module to use by USB cable.
But you need to solve the problem of how to power them, if you stack them together, it may need more power. Actually we do not test on how to stack them together, hope to get your understanding!
'''Q: Why the voltage warnings shows on my Pi?'''
Customer feeback: The board works as advertised with the 4a power supply they recommend but seems to lie really close to the voltage limit. I get a number of voltage warnings while using until I stopped using the KVM switch (which had a separate power supply) and just used a USB keyboard. Outside of that, assembled just fine and was able to configure a SSD 2.5 drive without issue.
* So we suggest that you can measure the output voltage of your power supply when under load your device. Please test directly the voltage value between GND and 5V PIN.
* We found that many power supplies on the market are known as 5V 4A output, but when use this power adapter at high current output , the voltage often drops very badly, with only about 4.7V or lower than 4.7V.
'''Q: What is the pinout for the PWR Switch?'''
* A: Please refer to here: [[PH2.0 Conector Specification]]
'''Q: How to do if I don't like the blue light on the power switch?'''
* It is ok to disable the blue light on the power switch, you just need to pull out the white cable. Please refer to the picture.
<gallery>
Turn-off-led-IMG-20181108-095055.jpg
</gallery>
'''Q:Is there really a 4tb limitDoes the X820 Power off switch work when the Pi is powered by USB (or PoE)? Will this '''* A: The X820 board not Power off switch cannot work with 6tb when the Pi is powered by USB (or 8tb?PoE).
===How to boot from a USB Mass storage device on a raspberry pi 3===
This tutorial explains how to boot your Raspberry Pi 3 from a USB mass storage device such as a flash drive or USB hard disk. Be warned that this feature is experimental and does not work with all USB mass storage devices. See this blog post from Gordon Hollingworth for an explanation of why some USB mass storage devices don't work, as well as some background information.
====Program USB Boot Mode====
Before a Raspberry Pi 3 will boot from a mass storage device, it needs to be booted from an SD card with a config option to enable USB boot mode. This will set a bit in the OTP (One Time Programmable) memory in the Raspberry Pi SoC that will enable booting from a USB mass storage device. Once this bit has been set, the SD card is no longer required. Note that any change you make to the OTP is permanent and cannot be undone.
If you wish, you can remove the ''program_usb_boot_mode'' line from config.txt, so that if you put the SD card in another Raspberry Pi, it won't program USB boot mode. Make sure there is no blank line at the end of config.txt. You can edit config.txt using the nano editor using the command ''sudo nano /boot/config.txt'', for example.
====Prepare the operating system image ====
Starting with the 2017-04-10 release of Raspbian you can install a working Raspbian system to a USB mass storage device by copying the operating system image directly onto your USB device, in the same way that you would for an SD card. To perform this step, follow the instructions [https://www.raspberrypi.org/documentation/installation/installing-images/README.md HERE], remembering to select the drive that corresponds to your USB mass storage device.
Please refer to here: [https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md USB mass storage device boot]
<comments />