X706

x706

x706

x706

x706

Overview

The X706 is a multifunctional expansion board for all current models of the Raspberry Pi using a 40 pin header. It provides an advanced uninterruptible power supply and power . The X706 can be stacked with other Raspberry Pi accessory boards for enhanced applications. The X706 can also be used with the X820/X825 (2.5" HDD/SSD Shield), X850/X855/X857 (MSATA SSD shield), X862（M.2 NGFF SATA SSD Shield）, X872/X873（NVMe M.2 SATA SSD Shield）.

Safety Instructions and Warnings

You must read these safety instructions and warnings before charging your batteries.

• Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the below instructions may result in fire, personal injury and damage to property if charged or used improperly.
• Never make wrong polarity connection when charging and discharging battery packs. Always double check polarity of battery's connector to make sure "+" to "+" and "-" to "-".
• Do not mix and use old batteries and new batteries, or batteries with different brand names.
• Lithium batteries has it's cycle life, please replace old battery with new one when it reaches it's service life or when it is two year old, whichever comes first.
• When charging Battery Pack, please put battery in a fire proof container. Please don't leave the X706 on the wood material or carpet and unattended.
• Must keep the X706 away from children.
• Please watch Main Video and Tutorial Video regarding 18650 batteries at: https://www.staysafebattery.com/en/

Features

FOR USE WITH	Raspberry Pi 1 Model B+/ 2 Model B / 3 Model B / 3 Model B+ / 3 Model A+ / 4 Model B
Operating System	Raspbian Stretch
KEY FEATURES	Smart Uninterruptible Power Supply (UPS) Out 5.1V enough 3000mA Power Backup for even the most demanding Raspberry Pi set ups Supports 3A via Type-C socket fast charging Can work with single or dual 18650 Lithium Ion battery Integrated battery protection circuit Integrated over current protection and over voltage protection Intelligent automatic charging and discharging On-board 4 green LEDs indicate battery charging and discharging levels of 25%, 50% , 75% and 100% On-board red LED show the status of battery charging or fully charged On-board push button to control power on /off (Press-ON, Hold the button pressed at least 2s -OFF) On-board pin header allows to select AUTO power-on when power supplied or battery installed Powers the Raspberry Pi via the 40-pin header - no additional cabling required Standard Raspberry Pi extension interface, compatible with other expansion boards Allows power input via Type-C socket or XH2.54 connector On-board XH2.54 power input connectors allows to integrate with your products DON'T supports software safe shutdown.
SPECIFICATION	Power supply via Type-C socket: 5Vdc ±5%, ≥3A; UPS output : 5.1V ±5% Max 3A UPS charging current: 1.8~2.2A Terminal Battery Voltage : 4.2V Recharge Threshold : 4.1V
NOTES	Do not apply power to your Raspberry Pi via the Micro USB socket or Type-C socket. Must use the battery with built-in protection circuit. NOT supports software safe shutdown.

Packing List

• 1 x X706 V1.1 18650 UPS Shield
• 1 x Jumper link Pitch 2.54mm
• 8 x M2.5 *5mm Screws
• 4 x M2.5 *20+6mm Spacers
• 4 x M2.5 *20mm Spacers

FAQ

Add your comment

Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.

Sort by date Sort by score

Enable comment auto-refresher

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #1

24 months ago

Score 0

Can the X706 be daisy chained to add more capacity?

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Lisa

24 months ago

Score 0

Hi，

x706 does not support external battery holder, only two batteries can be installed.If you want to use more batteries, please refer to X728, X708

Permalink