Difference between revisions of "X630-Hardware"
(10 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
==Interface== | ==Interface== | ||
− | [[File:X630-diagram.png]] | + | [[File:X630-diagram.png|800px]] |
==10-pin functional connector== | ==10-pin functional connector== | ||
Line 28: | Line 28: | ||
==X630 Reset Setting== | ==X630 Reset Setting== | ||
+ | '''Note: Software reset only exists in V1.3 version, this function is no longer reserved in V1.5''' | ||
+ | [[File:X630-V1.5-VS-X630-V1.3.jpg|700px|none|X630 V1.5 vs X630 V1.3]] | ||
+ | |||
[[File:Dip-switches.jpg|none|dip switch]] | [[File:Dip-switches.jpg|none|dip switch]] | ||
{| class="wikitable" | {| class="wikitable" | ||
Line 36: | Line 39: | ||
| Software reset || HW = 0 || SW = 1 | | Software reset || HW = 0 || SW = 1 | ||
|} | |} | ||
+ | |||
+ | [[File:X630-Reset-01.jpg|none|800px|X630 dip switch setting]] | ||
Explain: | Explain: | ||
* Hardware reset: After starting RASPISTILL or RASPIVID <span style="color:red;">once</span> then you will need to reboot Raspberry Pi to restart it again (Please use when operating system cannot control the X630 module via GPIO509) | * Hardware reset: After starting RASPISTILL or RASPIVID <span style="color:red;">once</span> then you will need to reboot Raspberry Pi to restart it again (Please use when operating system cannot control the X630 module via GPIO509) | ||
− | * Software reset: Starting RASPISTILL or RASPIVID <span style="color:red;">multiple times</span> and don't need to reboot Raspberry Pi | + | * Software reset: Starting RASPISTILL or RASPIVID <span style="color:red;">multiple times</span> and don't need to reboot Raspberry Pi |
− | * Default setting is ' | + | * Default setting is 'Hardware reset'; |
* Please remove the yellow protective film before change dip switch. | * Please remove the yellow protective film before change dip switch. | ||
Latest revision as of 11:33, 14 February 2023
Contents
Interface
10-pin functional connector
Pin No. | Pin Name | Function | Note |
---|---|---|---|
1 | 3V3 | 3.3V output | 3.3V |
2 | HDET | HDMI input detect (high level ) | 3.3V |
3 | IR | Infrared signal | 3.3V |
4 | INT | Interrupt Output signal – active high (Level) | 3.3V |
5 | RESET | System reset input, active low | 3.3V |
6 | A_SCK | I2S/TDM Bit Clock signal (BCK) | 3.3V |
7 | A_WFS | I2S Word Clock or TDM Frame Sync signal (LRCK) | 3.3V |
8 | A_OSCK | Audio Oversampling Clock (MCLK) | 3.3V |
9 | A_SD | I2S/TDM data signal (Data) | 3.3V |
10 | GND | Ground | 0V |
X630 Reset Setting
Note: Software reset only exists in V1.3 version, this function is no longer reserved in V1.5
SELECTION | SWITCH SETTINGS | |
---|---|---|
Hardware reset | HW = 1 | SW = 0 |
Software reset | HW = 0 | SW = 1 |
Explain:
- Hardware reset: After starting RASPISTILL or RASPIVID once then you will need to reboot Raspberry Pi to restart it again (Please use when operating system cannot control the X630 module via GPIO509)
- Software reset: Starting RASPISTILL or RASPIVID multiple times and don't need to reboot Raspberry Pi
- Default setting is 'Hardware reset';
- Please remove the yellow protective film before change dip switch.
Mechanical Drawing
Return to X630
Enable comment auto-refresher