X630

From Geekworm Wiki
Revision as of 16:39, 28 October 2021 by Cindy (talk | contribs)
Jump to navigation Jump to search

X630 HDMI TO csi-2
X630 HDMI TO csi-2
X630 HDMI TO csi-2
X630 Accessories and size

Overview

The X630 hdmi to csi module is a bridge module that converts HDMI stream to MIPI CSI-2, which enables your Raspberry Pi to accept HDMI video and audio streams and process them as incoming data source.

X630 HDMI to CSI-2 diagram

Features

  • Specifically designed mounting hole for the Raspberry Pi
  • HDMI to CSI-2 bridge chip: Toshiba TC358743XBG
  • Video Formats Support (Up to 1080P)
  • CSI-2 Transmit Interface MIPI CSI-2 compliant (Version 1.01 Revision 0.04 -2 April 2009)
  • CSI-2 connector: 15 pin FPC with 1.0 mm pitch
  • Able to start RASPISTILL or RASPIVID multiple times and no reboot required
  • Easily fixed on Raspberry Pi and DIY your pefect case

User Manual

Packing List

  • 1x X630 HDMI to CSI-2 Module
  • 1x X630-A1 Board
  • 1 x FPC cable(5cm length)
  • 1 x FPC cable-for backup(15cm length)
  • 2 x F/F M2.5*17mm Spacer
  • 4 x M2.5*6 Screw
  • 1 x M2.5 Nut


How to install X630

How to install X630

Match Metal Case

Please refer to X630-C1

FAQ

Q: What to do if there is no video output?

A: 1. When use the PI-KVM, please set the dip switches at the back of X630 to HW mode(Hardware reset mode). Pull the HW switch to 1 and pull the SW switch to 0.(Our default mode is SW mode.) Please set the switches at power off status. (For PiKVM usage, you will need to turn off SW reset DIP switch and turn on HW reset DIP switch prior to connecting the CSI cable to your Pi4.)

2. Software reset uses GPIO 509 to reset operation through GPIO. Please refer to wiki: X630-Software


Q: Which connector model is compatible with 10pin functional connector?

A: It is SH1.0 10Pin connector.

Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


Anonymous user #5

one month ago
Score 0++
Does the X630-A2 audio board work with PiKVM V2 DIY (using X630 and X630-C1 case)? Is any additional configuration required like on PiKVM-A3 or should this just work with pikvm without additional configuration?

Anonymous user #4

one month ago
Score 0++
How long will this product be in production/be supported?

Anonymous user #3

3 months ago
Score 0++
Which combination of X630 X630-A3 version is able of I2S audio adding the extra I2S cable ?

Walker

3 months ago
Score 0++
X630-A3 board with I2S interface and with I2S cable

Anonymous user #2

9 months ago
Score 0++
Thanks for the reply Walker - I'll try those 779 instructions again, but no success in past efforts.

Anonymous user #2

10 months ago
Score 0++
Since the X630-X2 is a board to pass Audio in to the I2C connection, a guide on activating the I2C audio input on the Raspberry Pi would be most appreciated.

Walker

10 months ago
Score 0++

Hello, you can refer to this: https://wiki...779-Software

There is a guide about audio input on the Raspberry Pi

Anonymous user #1

23 months ago
Score 0++
A 3D printed case for this wonderful product?

Lisa

23 months ago
Score 0++

Hi,

Sorry,there are currently no 3D printed case for X630.