X450

From Geekworm Wiki
Revision as of 12:22, 16 April 2020 by Abby (talk | contribs) (→‎Document)
Jump to navigation Jump to search
Raspberry pi HD Audio X450
Raspberry pi HD Audio X450
Raspberry pi HD Audio X450
Raspberry pi HD Audio X450
Switching power supply for X450

Overview

X450 DAC+AMP Expansion Board

Features

Item Description
Compatible with Raspberry Pi 1 Model B+/ 2 Model B / 3 Model B / 3 Model B+
Operating System Moode Audio Player
OSMC
Openelec
Raspbian Jessie
Volumio
Pi Core Player
Key Features Full-HD audio – up to 24-bit/192kHz playback
Audiophile ESS Technology Sabre premier stereo DAC ES9023
ES9023 delivers jitter-free studio quality audio with 112dB DNR
Built in High quality Class-D stereo audio amplifiers (TI TPA3116D2 x2)
Up to 2×100W Into a 4-Ω BTL Load at 21Vdc
Capable of driving 4 Ohm speakers (also works with higher impedance speakers)
Uses the Texas Instruments ultra-low-noise voltage regulator (output noise< 10μVRMS)
Uses the Texas Instruments high efficiency step-Down DC converter (up to 95%)
6V~26Vdc converted to 5.1V, 3A to power the Raspberry Pi
Uses the genuine ALPS RK163 series potentiometer for smooth volume adjustment
Built in high quality IR sensor (Vishay -the world's leading supplier of infrared receivers)
Onboard 3.5mm stereo headphone jack allowing audio input form other audio devices
Onboard pluggable speaker & power screw terminals
Onboard PH2.0 connector allowing to connect a lighted power switch
Onboard XH2.54 connector providing 5V output to power other devices
Onboard gold-plated high-current DC power jack (5.5x2.5mm)
Uses the digital I2S audio signals to reduce CPU load over USB audio solutions
Connects directly to the Raspberry Pi - No wiring required
Powers the Raspberry Pi - no additional power supply
Reserved Raspberry Pi GPIO pin header (2x13Pins)
Pop-noise can be improved by enabling GPIO control
AMP can be enabled / disabled with jumper link
Heat-sink attached to amplifiers for perfect heat dissipation
Specification Power supply: 6-26Vdc,≥3A recommended
GPIO used : LRCK - IO19, BCK - IO18, DATA - IO21, IR - IO26, AMP mute - IO22
Analog audio input level via onboard headphone jack : 2V RMS
Amplifier max output power: 2×100W at 4Ω BTL Load at 21Vdc
Resolution/Sampling Rate: upto 24bit / 192KHz (Raspberry Pi I2S)
PCB size 87 x 56mm
Note WARNING:
Do not apply power to your Raspberry Pi via the PI's Micro USB socket.

Packing List

  • 1 x X450
  • 1 x Installation screw pack

Document

Software Configuration: X450/X5500_Software_Configuration

Power Supply

This is single output 24V 10A 250W Switching power supply, and it can provide upto 250W power output.

Generay Specification

Item Description
Model S-250-24
DC output voltage, current 24V, 0~10A
Wave and noise 150mVp-p
Inlet wire stability ±1%
Load stability ±1%
Efficiency 81.50%
Adjustable range for DC voltage ±10%
Input voltage range 90~132VAC / 180~264VAC by Switch
Impact current (Cold start current) 25A/114VAC 50A/230VAC
OverLoad protection 105% ~ 135% cut off the output, automatic recovery
Over voltage protection 115%~150% shut down O/P voltage, re-power on the recovery
Setup, rise, hold up time 200ms, 50ms, 16ms/230vac at full load
Withstand voltage I/P-O/P 1.5kV I/P-FG 1.5kV O/P-FG 0.5kV 1minute
Isolation resistance I/P-O/P I/P-FG O/P-FG 500VDC/100MΩ
Working temperature -10℃ ~ +50℃
Dimension 215 x 115 x 50mm

FAQ

1. How to use the pin header marked “PWR ON” , “SPK MUTE” and “AMP OFF”?.

  • PWR ON: Short - Auto power on when power applied, Open – Using an external latching switch to control power on/off
  • SPK MUTE: Short – Speaker un-muted, Open – Mute enabled and it is controlled by GPIO22 with additional software setting e.g high = speaker unmuted, Low=speaker muted
  • AMP OFF: Short – speaker in shutdown mode, Open – Speaker in operation mode
Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


Anonymous user #5

29 months ago
Score 0++
why are there two power inputs?

Lisa

29 months ago
Score 0++
Hi,6~26V high power, when the load is large, you can use two power supplies to enhance the power supply.

Anonymous user #4

36 months ago
Score 0++
how to uaa the audio input? what software can I use to take this input and push to the speakers?

Anonymous user #3

49 months ago
Score 0++

when I look for DAC in VOLUMIO i don't see any x450 nor subtronic.

what is the correct selection to run this DAC?

Anonymous user #2

50 months ago
Score 0++
is there anyway to control the volume through software mixer (second anonymous user 2

Anonymous user #5

29 months ago
Score 0++
you can always adjust volume through software. this applies to all dacs and all audio solutions. How it is achieved depends on the software.

Anonymous user #1

54 months ago
Score 0++
Is there anyway to control the volume through software