Difference between revisions of "X1100 software"
(6 intermediate revisions by the same user not shown) | |||
Line 3: | Line 3: | ||
<mark><span class="tb_blue">'''Important! Increases the USB current limit to 1.6A'''</span></mark> | <mark><span class="tb_blue">'''Important! Increases the USB current limit to 1.6A'''</span></mark> | ||
− | By default, USB boot is not enabled with a 3A power supply or some third-party USB-PD capable power supply. If you are using a power supply that cannot provide 5A at +5V or not compatible, the current draw to USB peripherals will be restricted to 600mA and it might affect USB booting or cannot provide enough power to your hard drives and SSDs . | + | By default, USB boot is not enabled with a 3A power supply or some third-party USB-PD capable power supply. If you are using a power supply that cannot provide 5A at +5V or not compatible, the current draw to USB peripherals will be restricted to 600mA and it might affect USB booting or cannot provide enough power to your hard drives and SSDs .<ref>[https://www.raspberrypi.com/documentation/computers/raspberry-pi-5.html#usb-boot-and-power-supplies Raspberry Pi Official USB boot and power supplies]</ref> |
It is required that increases the USB current limit for peripherals to 1.6A by setting <span class="tb_blue">usb_max_current_enable=1</span> in the <span class="tb_blue">/boot/firmware/config.txt</span> file will override this and enable USB boot with a lower wattage power supply. | It is required that increases the USB current limit for peripherals to 1.6A by setting <span class="tb_blue">usb_max_current_enable=1</span> in the <span class="tb_blue">/boot/firmware/config.txt</span> file will override this and enable USB boot with a lower wattage power supply. | ||
+ | |||
Line 26: | Line 27: | ||
This means that the USB current limit has been increased to 1.6A - Success! | This means that the USB current limit has been increased to 1.6A - Success! | ||
+ | |||
+ | |||
+ | |||
+ | In addition, regarding the operation of SSD, you can refer to: [[How to Format and Mount the HDD/SSD on Raspberry Pi]] | ||
Return to [[X1100]] | Return to [[X1100]] | ||
+ | |||
+ | |||
+ | '''References:''' | ||
+ | |||
+ | <references /> | ||
<!--Add review function! --> | <!--Add review function! --> |
Latest revision as of 12:46, 8 December 2023
Important! Increases the USB current limit to 1.6A
By default, USB boot is not enabled with a 3A power supply or some third-party USB-PD capable power supply. If you are using a power supply that cannot provide 5A at +5V or not compatible, the current draw to USB peripherals will be restricted to 600mA and it might affect USB booting or cannot provide enough power to your hard drives and SSDs .[1]
It is required that increases the USB current limit for peripherals to 1.6A by setting usb_max_current_enable=1 in the /boot/firmware/config.txt file will override this and enable USB boot with a lower wattage power supply.
Open then Teminal window, then run the following command to open the /boot/firmware/config.txt file:
sudo nano /boot/firmware/config.txt
Add a line at the end of the file that reads like this:
usb_max_current_enable=1
Save and exit. In Nano editor, you do that by hitting CTRL + X, answering Y and hitting Enter when prompted.
Reboot the Raspberry Pi
sudo reboot
You can check the status of power output to the USB ports using vcgencmd.
vcgencmd get_config usb_max_current_enable
This means that the USB current limit has been increased to 1.6A - Success!
In addition, regarding the operation of SSD, you can refer to: How to Format and Mount the HDD/SSD on Raspberry Pi
Return to X1100
References:
Enable comment auto-refresher