5,026
edits
Changes
Jump to navigation
Jump to search
We strongly recommend that '''DON'T use Raspberry Pi OS Lite version''', It will lack some dependent software by default, unless you are a linux proficient, you can install some dependent software yourself
login Login to mynode teminal via Putty or Xsheel tool, the default user name is `admin`, default password is `bolt`, then run the following command: Login to mynode teminal via Putty or Xsheel tool, the default user name is `umbrel`, default password is `moneyprintergobrrr`, then run the following command: '''FAQ''' Q: What are the credentials to SSH into my Umbrel? A: ssh umbrel@umbrel.local (or ssh umbrel@<IP address of your Umbrel>). The password is the same as your Umbrel's password. If you haven't set a password yet, the default password is: moneyprintergobrrr.
{{GD Template Impl}}
[Update]
Support [https://getumbrel.com/ Umbrel] now.
The script is '''not tested''' VMware ESXI ARM operating system.
To make the 3pin PWM cooling fan running, please remove/pull out the yellow cable if you use X-C1 V1.3 version.
Remove the jumper cap on "Fan FS" PIN of X-C1 V2.0 to let the fan running at full speed.
NOTE:
==For Raspbian / RetroPie / Twister OS v2.0.2 ==
Test this script based on the following OS:
* Tested '2022-04-04-raspios-buster-armhf.img" on Apr. 13, 2022;* Raspbian 2021-05-07-raspios-buster-armhf, 2021-10-30-raspios-bullseye-armhf.img, 2021-10-30-raspios-bullseye-armhf-lite.img
* RetroPie 4.7.1
* Twister OS v2.0.2 / Twister OS 2.1.2
'''install'''
cd ~
sudo apt-get update
sudo apt-get -y upgrade sudo apt-get -y install i2c-tools python3-smbus python3-rpi.gpio sudo apt-get install -y pigpio pythongit sudo apt-get install -y pigpio python-smbus python3-pigpio wiringpi git
git clone https://github.com/geekworm-com/x-c1.git
cd x-c1
sudo chmod +x *.sh
sudo bash install.sh
echo "alias xoff='sudo /usr/local/bin/x-c1-softsd.sh'" >> ~/.bashrc
sudo reboot
If reboot fails, please force shutdown or power off and restart
''' PWM fan control'''
sudo apt-get upgrade
sudo apt-get install -y unzip make gcc python git wiringpi python3-pigpio python-setuptoolspython3-rpi.gpio
sudo apt-get install -y python3-distutils
</pre>
== For myNode OS and Umbrel ==
About myNode, please refer to http://www.mynodebtc.com/
About Umbrel, please refer to https://getumbrel.com/
'''Install'''
<pre>
sudo apt-get update
== For DietPi==
About DietPi, please refer to [https://dietpi.com/ URL]
Test 'DietPi_RPi-ARMv6-Bullseye.image' on May 5th, 2022.
'''Install'''
<pre>
sudo apt-get update
sudo apt-get install git pigpio python pythonpigpiod python3-pigpio pythonpython3-smbus wiringpi python3-rpi.gpio -y
git clone https://github.com/geekworm-com/x-c1
cd x-c1
return to [[NASPi]]
==For Volumio ==
Test this script based on the following OS:
* Volumio-3.175-2021-12-13-pi.img
'''install'''
cd ~
sudo apt-get update
sudo apt-get upgrade
sudo apt-get install -y git pigpio
sudo apt-get install -y python-pigpio python3-pigpio
sudo apt-get install -y python-smbus python3-smbus
git clone https://github.com/geekworm-com/x-c1.git
cd x-c1
sudo chmod +x *.sh
sudo bash volumio.sh
echo "alias xoff='sudo /usr/local/bin/x-c1-softsd.sh'" >> ~/.bashrc
sudo reboot
''' PWM fan control'''
The script is installed successfully and the fan starts to run
'''Test safe shutdown'''
xoff
* Please run 'xoff' to shut down or press the on-board button switch to shut down. <span style="color:red;">DON'T run the 'shutdown' linux command to shut down, otherwise the power of X-C1 will not be shut down.</span>
* press button switch `1-2` seconds to reboot
* press button switch `3` seconds to safe shutdown,
* press `7-8` seconds to force shutdown.
'''uninstall'''
<pre>
sudo ./uninstall.sh
</pre>
'''Note'''
<pre>
Enable SSH:
http://volumio.local/dev/
Name: volumio
Password: volumio
</pre>
we use the default password to run the volumio.sh, please replace default password 'volumio' with your new password in volumio.sh file .(Line 72)
==FAQ==
Q1: Can't connect to pigpio at localhost(8888)
<pre>
Can't connect to pigpio at localhost(8888)
Did you start the pigpio daemon? E.g. sudo pigpiod
Did you specify the correct Pi host/port in the environment
variables PIGPIO_ADDR/PIGPIO_PORT?
E.g. export PIGPIO_ADDR=soft, export PIGPIO_PORT=8888
Did you specify the correct Pi host/port in the
pigpio.pi() function? E.g. pigpio.pi('soft', 8888)
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
Traceback (most recent call last):
File "/home/volumio/x-c1/fan.py", line 8, in <module>
pwm.set_mode(servo, pigpio.OUTPUT)
File "/usr/lib/python2.7/dist-packages/pigpio.py", line 1376, in set_mode
return _u2i(_pigpio_command(self.sl, _PI_CMD_MODES, gpio, mode))
File "/usr/lib/python2.7/dist-packages/pigpio.py", line 1025, in _pigpio_command
sl.s.send(struct.pack('IIII', cmd, p1, p2, 0))
AttributeError: 'NoneType' object has no attribute 'send'
</pre>
A: If you find an error similar to the above, it is because pigpiod library is not started, we need to run pigpiod first,
sudo pigpiod
python 'your directory'/x-c1/fan.py &
If 'sudo' command request a password, you can use the following command:
echo 'your password' | sudo -S pigpiod
python 'your directory'/x-c1/fan.py &
You can put these two lines in the /etc/rc.local file so that it will run automatically after booting.
[[File:Volumio-rc-local.jpg|800px]]
Q2:How to get the current fan speed value? As I remember old x735 software where with such read_fan_speed.py script example, but not found such in X-C1.
A: The X-C1's PWM fan is a 3Pin FAN, and does not support reading speed. The Fan of X735 is a 4Pin PWM fan.
<hr/>
<!--Add review function! -->
<comments />
[[Category:Product Manual]]
[[Category:Raspberry pi]]
[[Category:Knowledge]]