From Geekworm Wiki
Revision as of 14:50, 28 September 2021 by Lisa (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

T300-C3 Packing List


The T300-C3 case is compatible with T300 V1.1 2.5 inch SATA SSD/HDD Shield & Jetson nano A02/B01/2GB version.

Note: The NVIDIA Jetson Nano Developer Kit and antenna are not included, and the 4-pin cooling fan is not included aslo!


  • Compatible with Jetson Nano Development Board Rev A02 and Rev B01 and 2GB version!!
  • With power switch and Reset switch, it is convenient to start with one button;
  • The power switch has an LED light display;
  • The reset switch is placed on the back to prevent accidental touch;
  • Support fan installation, reserve 22mm high fan installation height; easy to install the official recommended fan;
  • The antenna hole is reserved to facilitate the arrangement of the external antenna;
  • Easy to install;

Check which version of JETSON NANO A02/B01 you are using

Jetson Nan0 A02&B01 Compare.jpg

How to connect


1) There are two jumper caps in the screws pack. ①Because this case has a power control switch, you need to disable the AUTO ON function firstly. Please insert one jumper cap into the “AUTO ON” position of the J40 pin to disable the AUTO ON function. ②Another Jumper cap is used to toggle the power supply between Micro USB and DC Jack. Insert this jump cap in "J48" Pin to disable Micro USB PWR to power (enable the DC 5V 4A jack PWR). The power control switch should be insert into “ON” pin at J40. And the blue and white cable of power control switch need to be insert in “3.3V” and “GND” pin at J41.

2) The reset switch should be insert in “RST” pin at J40. Please refer to the photo3 at the back.

3) A camera bracket is added for raspberry pi official camera, can fix the camera on the top or side of the case, adjust the camera position as your requirement. Please refer to the photo1 at the back.

About cooling fan

The case is reserve 22mm high fan installation height , it is recommend to use Noctua NF-A4x20 5V PWM fan, we prepair 4 pcs PM2.5*22 screws and 4 pcs M2.5 nuts and 4 pcs gaskets to install this fan. You need to use the ABS tweezers when you install this fan. Please see the video.

Packing List

  • 1 x Metal Case for T300 V1.1 & NVIDIA Jetson Nano Board
  • 1 x Power Switch (Momentary switch)
  • 1 x Reset Switch (Momentary switch)
  • 2 x Jumper (Disabled the AUTO ON, and toggle the power supply)
  • 1 x Screws Pack
  • 1 x ABS Tweezers (It is useful when you install a fan only)


Q1: Why was the MICRO SD card slot cancelled?

A: T300-C3 is compatible with A02, B01 and 2GB versions now. We must increase the distance between the JETSON NANO motherboard and the front panel of the case to install the switch. We found that even if we kept the TF card slot, we couldn’t insert the TF card by hand or plastic tweezers, so we have to cancel this card slot; We hope that the official NVIDIA will adjust the position of J50 in subsequent versions. For more questions, please refer to the official forum link: https://forums.developer.nvidia.com/t/stop-shipping-the-nvidia-jetson-nano-development-kit-b01-j50-is-on-the-wrong-side/112066

Customer Review

1. Putting An Nvidia Jetson Nano Dev Kit into a Geekworm N100 Metal Case with Power & Reset Control Switches

Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.

Anonymous user #1

31 months ago
Score 0++
Other cases have an extension board for the TF card, but having 2 spring-loaded latches makes using them a real pain.


31 months ago
Score 0++
Hi,Because of the renewal of the motherboard design, we had to cancel the TF interface. Please refer to FAQ. hope to get your understanding.