Recent changes
Jump to navigation
Jump to search
Track the most recent changes to the wiki on this page.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
23 April 2024
|
|
04:54 | (Comments log)[47.181.223.243; 136.23.0.128] | |||
|
|
04:54 47.181.223.243 talk posted a new comment on X650 (Resolved. Board v.1.5 is still using pcf8563 not ds1307 so no change in config.txt is necessary.) | ||||
|
|
02:47 136.23.0.128 talk posted a new comment on X1011 (I would also like a case produced. Thanks) Tags: Mobile web edit, Mobile edit | ||||
22 April 2024
|
|
15:48 | (Comments log)[90.77.46.17; 177.99.103.158; 108.76.201.4 (2×)] | |||
|
|
15:48 90.77.46.17 talk posted a new comment on XScript (If I do not install the script, I can still switch on and switch off my Pi4 with the X-C1 board. Is that save or is it like a hard shut off which might corrupt my SD card?) | ||||
|
|
05:33 108.76.201.4 talk posted a new comment on X1001 (I posted as anon user #15 earlier. I think I got the problem resolved by routing the cable a little differently. I noticed I did not have the problem if the device was outside of the case (Geekworm P579-V2-K). I tried adding some electrical tape to the inside of the case (per Q4), but that didn't make a difference. However, I noticed that, when the pi was installed in the case, the FCC cable was being pressed against the inside of case, which caused it to bend some and appeared to cause...) | ||||
|
|
04:04 177.99.103.158 talk posted a new comment on X1001 (Is there a way to disable the LED light, its so annoying.) | ||||
|
|
01:14 108.76.201.4 talk posted a new comment on X1001 (I've installed the X1001 with a 128GB Silicon Power P24A60 (Model A60), and it has booted and ran fine for at least an hour or so, then everything just stops responding and basic commands like sudo and ls are no longer found. It behaves as though the drive has being disconnected, but the blue light is still on when this happens. I have re-seated the FCC cable on both ends a few times. It seems to be seated fully and securely. Also, the drive is typically recognized (at least momentarily)...) | ||||
21 April 2024
| 09:39 | Comments log 212.102.44.164 talk posted a new comment on X-UPS1 (When multiple boards are stacked can I use the outputs on all boards, or only the first? Thanks!) | ||||
20 April 2024
|
|
05:22 | (Comments log)[64.77.248.35; 38.39.78.45; 47.181.223.243 (2×)] | |||
|
|
05:22 47.181.223.243 talk posted a new comment on X650 (additional error: "dmesg | grep rtc [ 8.242339] rtc-ds1307: probe of 1-0068 failed with error -5") | ||||
|
|
04:05 64.77.248.35 talk posted a new comment on P511 (What is the screw size if I want to get replacements) | ||||
|
|
02:25 47.181.223.243 talk posted a new comment on X650 (even after replacing with dtoverlay=i2c-rtc,ds1307 I'm getting error: No usable clock interface found. hwclock: Cannot access the Hardware Clock via any known method. and there is no /dev/rtc or /dev/rtc0) | ||||
|
|
02:03 38.39.78.45 talk posted a new comment on How to Format and Mount the HDD/SSD on Raspberry Pi (thanks, was confused getting my m.2 setup!:)) | ||||
19 April 2024
|
|
08:43 | (Comments log)[81.31.126.114; 69.251.186.62] | |||
|
|
08:43 69.251.186.62 talk posted a new comment on X1202 (THE disable power on modification does not work. when power is applied to the dc port or usb c the pi still auto boots.) | ||||
|
|
00:22 81.31.126.114 talk posted a new comment on X1011 (Thank you Lisa :)) | ||||
18 April 2024
| 23:02 | Comments log 73.222.165.68 talk posted a new comment on PiKVM-A3 (Where can I get sdupport for my video output. Ive tried everything and it just isnt showing video. It isnt being detected by my host when HDMI is connected. All my other settings work great.) | ||||
17 April 2024
|
|
22:07 | (Comments log)[96.73.134.142; 93.193.82.220; 85.171.213.233; 81.31.126.114; 72.26.41.30; 149.36.48.86; 103.192.227.240] | |||
|
|
22:07 81.31.126.114 talk posted a new comment on X1011 (Is it possible to disable the 4 blue status LED's?) | ||||
|
|
20:14 72.26.41.30 talk posted a new comment on P580 (My wifi no longer works once the raspberry pi & X1002 are installed in the case. Do you have recommendations on how to resolve this?) | ||||
|
|
18:05 85.171.213.233 talk posted a new comment on X306 (Does any 18650 battery fit the x306 or is there any recommendation on max discharge current, voltage ?) Tags: Mobile web edit, Mobile edit | ||||
|
|
16:13 149.36.48.86 talk posted a new comment on M901 (Hi, I bought an X1001 a few months ago, which has worked great with a WD SN770. I just bought an M901, thinking it should be about equivalent to the X1001, but my second SN770 isn't recognized.) | ||||
|
|
14:44 103.192.227.240 talk posted a new comment on X1002 (We apologize, but if you find the wrong screws, please simply request a refund.) | ||||
|
|
05:52 93.193.82.220 talk posted a new comment on X735-script (Hi, running the steps to install fan, pwr and sss the fan doesn't start. The os version is new one:OS Version: Raspberry OS 6.6.26-v8+ With the new gpiolib the script read_fan_speed.py starts successful but "0 RPM" is not what i want to see :-) Before i use the new documentation to install i try to install everything with the deprecated tutorial, may be this can be the problem ... It would be great if you could help. Lars) | ||||
|
|
01:51 96.73.134.142 talk posted a new comment on X1202 (When you charge battery via USB C, pi boots if turned off. how to disable so charge battery without pi booting.) | ||||