Main public logs

Combined display of all available logs of Geekworm Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

• 12:06, 22 May 2026 Ruby talk contribs performed unknown action "comments/add" on X1009 (Sorry for the late reply. We currently cannot release firmware updates for the X1009. But We've updated the FAQ and added relevant info to product documents (please refer to #FAQ-Q2. Thanks a lot for your feedback.)
• 06:20, 20 May 2026 185.82.238.74 talk performed unknown action "comments/add" on X1009 (I found a solution and I am updating my original post. Thanks to an article at www.root.cz/zpravicky/#zpravicka-9 and a subsequent discussion on the RPi forum at forums.raspberrypi.com/viewtopic.php?t=394580&sid=5cdec88004c1bedee4b2a8fb34b4e510&start=125#p2375717 regarding the Radxa controller (which uses the same JMB585 controller), I followed the instructions and added the line dtoverlay=pcie-32bit-dma-pi5 to /boot/firmware/config.txt. Everything is now working under the 6.18.x kernel branch.)
• 01:24, 16 May 2026 90.143.203.117 talk performed unknown action "comments/add" on X1009 (Just fixed this problem myself just now (your answer didn't exist when I read here before). Ran some updates through openmediavault and got hte problem. I can say that 6.12.87 does not work either, but 6.12.75 does. Will there be any updated firmware etc to avoid problems like this in the future??)
• 22:21, 15 May 2026 93.172.4.191 talk performed unknown action "comments/add" on X1009 (thank you)
• 17:11, 15 May 2026 80.188.220.2 talk performed unknown action "comments/add" on X1009 (I forgot to mention, that I am on latest raspbian lite 64bit (trixie). I have tried change setting for PCIe in config.txt...nothing helped...only downgrade.)
• 06:04, 15 May 2026 185.82.238.74 talk performed unknown action "comments/add" on X1009 (Hello, I have just found out, that x1009 doesn't work with kernel 6.18.x branch. I had to downgrade back to 6.12 branch.)
• 17:15, 9 February 2026 Ruby talk contribs performed unknown action "comments/add" on X1009 (Sorry, there’s no ready-made plug-and-play LED connector – the only way is to solder external wires to the LED's pads.)
• 10:26, 6 February 2026 161.51.55.245 talk performed unknown action "comments/add" on X1009 (The X1009 combined with the Pi5 looks almost perfect to replace my ageing NAS. The only problem for me is there doesn't appear to be any LED output connector from the X1009 to power external individual drive LEDs on the front on my existing Tranquil PC case. Is there any easy way to power external drive activity LEDS? Thank you)
• 16:07, 12 January 2026 194.230.161.78 talk performed unknown action "comments/add" on X1009 (Thanks for the answers.) Tags: Mobile edit Mobile web edit
• 17:51, 7 January 2026 Ruby talk contribs performed unknown action "comments/add" on X1009 (Hi there! Thanks for your questions about the Geekworm X1009. Here are the answers: 1. We haven’t tested whether the latest firmware supports booting from HDD/SSD yet. 2. It uses the JMB585 PCIe to SATA chip. 3. The SATA power connector (5V, 12V) is controlled by the Raspberry Pi’s 3.3V pin. Feel free to reach out if you have any other questions!)
• 00:24, 3 January 2026 188.154.133.223 talk performed unknown action "comments/add" on X1009 (Hello, I have some Questions: The X1009 is designed for data storage purposes and does not currently support booting from HDD/SSD with the existing firmware. Any positive news on this now? - Which PCIe to SATA chip is used? I assume JMB585? - Is the SATA power connector(5V, 12V) switched by EN-pin of the Pi? Like fullsize PCIe connector on the x1010?)
• 11:02, 18 July 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (We need you to provide installation pictures and test videos to troubleshoot and find the cause. It is difficult to determine the cause based on your description. could you please send pictures or videos via email, which is more convenient for communication. Hope to get your understanding.)
• 18:47, 17 July 2025 2.220.128.133 talk performed unknown action "comments/add" on X1009 (Gotcha. No more Geekworm products for me, ever.)
• 16:42, 17 July 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Since we don't know how you use it, we can't analyze the cause. Please send the test video by email and please send a picture of the power supply you use.)
• 21:09, 16 July 2025 2.220.128.133 talk performed unknown action "comments/add" on X1009 (@Lisa of course I already restarted, tried a different FCC, and even a different Raspberry Pi 5B. Took off all the harddrives and just had the naked shield connected - controller was not recognized in any of these cases. I just want to know what could have possibly caused this so I know whether to replace the broken one with a new one or migrate to another solution instead that doesn't involve an X1009.)
• 16:47, 15 July 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hi, Restart and test again. If it still cannot be recognized, please contact us by email <info@geekworm.com>. Tell us your order number and more details. Thank you.)
• 00:08, 14 July 2025 90.222.31.126 talk performed unknown action "comments/add" on X1009 (All of a sudden, my X1009 is no longer recognized by my Pi. the powerLED on the shield remains red.)
• 18:14, 24 June 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hi, yes, you can power the RPi5 via Type C. because X1009 needs the V3.0V control of the RPi5，can not disconnect it all. You need to unplug the pins of PIN2 and PIN4 of expansion header (GPIO bridge connector) .)
• 18:14, 24 June 2025 Lisa talk contribs performed unknown action "comments/delete" on X1009
• 18:14, 24 June 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hi, yes, you can power the RPi5 via Type C. You need to unplug the pins of PIN2 and PIN4 of expansion header (GPIO bridge connector) . because X1009 needs the V3.0V control of the RPi5，can not disconnect it all.)
• 14:31, 24 June 2025 173.70.167.178 talk performed unknown action "comments/add" on X1009 (> Hello, does not support power X1009 via Type C of RPi5. Thanks for your answer, Lisa! So I need to disconnect GPIO bridge connector if I want to power PI and X1009 separately? As documentation says: Don't power the X1009 via DC powe jack and the Raspberry Pi5 via USB-C at the same time. Just power the X1009, and then the X1009 will power the Pi 5 via the GPIO.)
• 15:09, 23 June 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hello, does not support power X1009 via Type C of RPi5.)
• 05:13, 21 June 2025 173.70.167.178 talk performed unknown action "comments/add" on X1009 (Is it possible to power the Raspberry Pi 5 via a USB Type-C cable, while powering HDDs directly from an independent 12V power supply? In that case, will the Raspberry Pi 5 still be able to power the X1009 over GPIO — essentially in reverse? The DC 12V 5.5x2.1mm power input would not be used in this setup. If that is not possible, then I will need to use two 12V power supplies: - one 12V power supply for the X1009 (and Raspberry Pi 5) - another 12V power supply for the HDDs. The reason I'm...)
• 10:02, 26 May 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hello, It's a SATA Power VH3.96-4P Connector；5V out for SSD/HDDs / GND/ 12V out for HDDs; Please refer to the X1009 V1.1 Interface Diagram.)
• 10:01, 26 May 2025 Lisa talk contribs performed unknown action "comments/delete" on X1009
• 10:01, 26 May 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hello, It's a SATA Power VH3.96-4P Connector；5V out for SSD/HDDs / GND/ 12V out for HDDs; Please refer to the X1009 V1.1 Interface Diagram.)
• 15:40, 23 May 2025 84.97.28.116 talk performed unknown action "comments/add" on X1009 (Hi, What is the model of the SATA power connector on the board? Thanks)
• 10:46, 16 April 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hello,sorry only the Dimensions source file (DXF))
• 17:36, 15 April 2025 81.57.126.239 talk performed unknown action "comments/add" on X1009 (Hello, Is there perhaps and cad model of the board? 3mf, stl etc)
• 14:39, 7 April 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hello,it is depend on your power supply.)
• 05:42, 5 April 2025 46.223.148.224 talk performed unknown action "comments/add" on X1009 (Hello, how much current can the on board 5C DCDC converter deliver? 5A or only 3A?)
• 11:24, 31 March 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hi, you can use 12Vdc +/-5% ≥11A for five 3.5" HDDs.)
• 15:15, 28 March 2025 47.96.236.37 talk performed unknown action "comments/add" on X1009 (Can a 12Vdc-15A power supply be used?)
• 17:23, 19 March 2025 62.176.175.178 talk performed unknown action "comments/add" on X1009 (Okay, so only the barrel jack)
• 12:01, 19 March 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (You can power the HDD separately, but it does not support powering the X1009 HAT from the HDDs.)
• 03:55, 19 March 2025 77.23.255.54 talk performed unknown action "comments/add" on X1009 (I bought a defect X1009 SATA Shield and they refunded my money. But they refuse to allow me to purchase it again. :( So if your X1009 SATA Shield works its fine. But if not you will not get any support.)
• 21:27, 18 March 2025 62.176.175.178 talk performed unknown action "comments/add" on X1009 (Dear Lisa and Harry, as mentioned earlier, i am powering my HDDs with Corsair 850 W ATX PSU. That is fine, now, i would like to use 5 V output from Corsair to power Raspi to sort of offload onboard (on the SATA hat) 12 V to 5 V regulator. Can i feed 5 V from Corsair to the hat via the HDD connector? As You can imagine, Corsair has plenty of power for my Raspi and this way i would like to derease heat produced by the hat... thanks)
• 16:46, 13 March 2025 62.176.175.178 talk performed unknown action "comments/add" on X1009 (Dear all, despite the fact i wanted to use latest ubuntu image on my Raspi, i tried latest Raspi image without desktop and everything works like charm. I did not even had to enable pci port:) I will put the Ubuntu card in and make video hopefully next week or so. Many thanks.)
• 11:44, 13 March 2025 Harry talk contribs performed unknown action "comments/add" on X1009 (To determine whether it is caused by the power supply or the system, can you provide a detailed video to describe the problem? You can email to us.)
• 11:42, 13 March 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Thanks for the information. Could you please send a test video via email [support@geekworm.com]? It would be easier to identify the problem with a test video.and please let us known the order NO.)
• 18:24, 12 March 2025 62.176.175.178 talk performed unknown action "comments/add" on X1009 (HDDs are 5x Seagate Skyhawk ST4000VX016 PS: once booted, if i connect the fifth to shield, it is recognised:))
• 18:16, 12 March 2025 62.176.175.178 talk performed unknown action "comments/add" on X1009 (Dear Lisa, i understand the power supply needs. Now i connected Corsair 850 W ATX PSU to disks. I have found out that if i connect all 5 HDDs to the shield, the Raspi would not boot. As long as i disconnect one (i tried first on port 0 and fifth on port 4), raspi boots like charm :))
• 11:55, 12 March 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (You can choose the appropriate power supply according to your needs. 12Vdc +/-5% ≥5A for two 3.5" HDDs, ≥7A for three 3.5" HDDs, ≥9A for four 3.5" HDDs, ≥11A for five 3.5" HDDs 12Vdc +/-5% ≥4A for two 2.5" HDDs, ≥5A for three 2.5" HDDs, ≥6A for four 2.5" HDDs, ≥7A for five 2.5" HDDs Your SATA drives can also be powered from a separate PSU. You need to calculate the total current required for all the HDDs you are using. Check the HDD nameplate to get the HDD startup current (the startup cu...)
• 03:32, 12 March 2025 91.127.238.207 talk performed unknown action "comments/add" on X1009 (Hi Lisa, i thought that the 5V regulator would not be able to supply 5 A to raspi and also 5 V to all five HDDs)
• 11:19, 7 March 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (Hi，I'm confused as to why you separated it?)
• 23:32, 6 March 2025 62.176.175.178 talk performed unknown action "comments/add" on X1009 (Raspi is running Ubuntu server without desktop)
• 23:31, 6 March 2025 62.176.175.178 talk performed unknown action "comments/add" on X1009 (Dear all, are those two pins on 6 pin header that connects Raspi and this board neccessarry? As i tried not to connect them, to power raspi from separate supply and HDDs from other 12 V supply, the shield did not seem to work at all. I am trying to separate it as if i plug all 5 HDD seagate skyhawk 4 TB to the board, the raspi does not boot, even if the board provide 5V on the headers powering raspi.)
• 10:28, 27 February 2025 Lisa talk contribs performed unknown action "comments/add" on X1009 (It does not support setting to disable LEDs.)
• 20:29, 26 February 2025 87.123.33.143 talk performed unknown action "comments/add" on X1009 (Is there a possibility to disable the LED's?)
• 00:48, 10 February 2025 86.90.217.133 talk performed unknown action "comments/add" on X1009 (where can I find a barrel plug which can handle the max? I haven't been able to find one)