X1208

Overview

The X1208 UPS+POE Shield is engineered to provide the Raspberry Pi 5 with both a reliable power source and enhanced storage. It features an integrated M.2 NVMe SSD slot, ensuring robust data backup even during a power loss. This powerful combination safeguards valuable data, boosts system reliability, and guarantees continuous operation.

The X1208 delivers a stable 5.1 V/5 A backup power supply, enabling uninterrupted performance for demanding setups—from intensive applications to multiple peripherals. Its advanced power-management system intelligently monitors the Pi's status, automatically cutting power after shutdown to optimize battery life with ultra-low standby consumption. The board ensures seamless power switching during outages or adapter failures and supports convenient features such as auto power-on and AC power-loss detection.

SAFETY INSTRUCTIONS AND WARNINGS

The default charging current is set to 1.5A and charge cut-off voltage is 4.23V. before connecting your battery to the UPS board, Please carefully confirm the maximum charging current and voltage, exceeding the upper limit of the charging specification that the battery can withstand will not only cause adverse reactions, but may also cause irreversible damage.
It is essential to read and understand these safety instructions and warnings before charging your batteries.
Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.
Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".
Do not mix and use old batteries with new batteries, or batteries with different brand names.
Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.
When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material or carpet unattended.
Keep the UPS shield away from children to ensure their safety.

Features

For use with	Raspberry Pi 5
Key Features	UPS Output Built for continuous, long-lasting operation -providing unwavering power for always-on Raspberry Pi 5 systems Supports a maximum current output of 5.1V 5000mA, suitable for most Raspberry Pi 5 applications Integrated Advanced Power MOSFET with an equivalent of 7mΩ RDS(ON) to minimize power loss Power the Pi 5 directly through the 40-pin header, eliminating the need for cables and soldering Battery Charging Supports battery charging with a capacity of 1500mA Battery charging control can be managed via GPIO Provides protection against battery overcurrent and overvoltage Built-in protection against reverse connection of battery cells Integrated Maxim's fuel-gauge systems for reading battery voltage and percentage over I2C On-board LEDs indicate battery charging and discharging levels of 25%, 50%, 75%, and 100% Features a single 21700 battery holder, supporting a battery of up to 5000mAh(Compatible only with unprotected 21700 battery up to 70.3 mm in length.) Power Input Powered through the USB-C socket, eliminating the need to change your power adapter Enhanced Power Management Seamless power switching between backup power and the power adapter On-board push button performs the same actions as the Pi's power button Automatically cuts off power when the Pi 5 is shut down On-board LED indicates power status and Pi 5 detection AC power loss and power adapter failure detection via GPIO Auto power-on when power is applied or restored Automatic safe shutdown when battery voltage is low (programmable) Ultra-low standby power consumption to maximize battery life Advanced system power-path management to minimize frequent charging and discharging of batteries M.2 M key NVMe socket Supports high-capacity M.2 NVMe solid-state drives up to 4TB Accommodates various M.2 NVMe SSD form factors, including 2280, 2242, and 2230 Supports operating system booting from your SSD Offers fast data transfer speeds with PCIe 2.0 5Gbps / PCIe 3.0 8Gbps Does not compromise cooling performance and is fully compatible with the official active cooler Features a blue LED indicator that displays power and drive status High-efficiency converter delivers 3.5A to your SSD Compatible Accessories X1100 USB3 to SATA 2.5 HDD/SSD shield for Pi 5 Other add-on boards that do not use the PCIe interface are attached to the bottom of the Raspberry Pi 5.
Spec	Power input: 5Vdc 5A via USB-C (Input current below 5A may cause improper operation.) UPS output: 5.1V ±5% Max 5A Battery charging current: 1.5A Terminal Battery Voltage: 4.23V Battery Recharge Threshold: 4.1V Ports & Connectors: USB-C power in connector x1 1-cell 21700 battery connector x1 SSD socket - M.2 KEY-M 67P x1 40-pin extended GPIO header x1 PCB Size: 86.5mm x 84.5mm
Important Notes	Do not apply power to your Raspberry Pi 5 via the Type-C USB socket. Compatible with unprotected 21700 battery only (Max. battery length: 70.3 mm).

Packing List

1x X1208 V1.0 UPS + NVMe Board
2x PCIe FFC Cable (40mm length)
1x Pogo Pin (for connecting to the Pi 5 PSW through-hole)
4x M2.5x13.5mm F/F Spacers
1x Screw Kit

Matching Case

There is no matching case for X1208 right now! Please looking forward to the future update.

User Manual

X1208 Hardware
X1208 Software Guide:[1]

FAQ

Q1: Question 1

A: Place the answer here.

Enable comment auto-refresher