Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 21:06, 25 July 2023 219.165.222.129 talk posted a new comment on PiKVM-A8 (Harry, thanks for your reply. I was writing vaguely. I was understanding the polarity of the LEDs on the case. I couldn't figure out which pin of the "TO PANEL" connector on the X630-A8 board should have positive polarity. But it resolved. I looked at the packing list. The polarity was written on the silk on the side that was hidden after assembly. Thank you.)
  • 19:05, 25 July 2023 Harry talk contribs posted a new comment on PiKVM-A3 (Hi, the RTC clip is different with ofical pikvm. <pre> rw sudo nano /boot/config.txt #Then change the line: dtoverlay=i2c-rtc,pcf8563 to dtoverlay=i2c-rtc,ds1307 #Test RTC #Display the current time of the Raspberry Pi date #Write the time of Raspberry Pi to DS1307 reboot before next step sudo hwclock -w #Read the time of DS1307 sudo hwclock -r ro </pre>)
  • 18:42, 25 July 2023 Harry talk contribs posted a new comment on PiKVM-A8 (What is the polarity of the "TO PANEL" connector? Answer: The end of the cable from the PANEL will have an identifier Is the pin on the side closest to the board positive or negative? Answer: This depends on your computer motherboard, please refer to your motherboard manual, you can find your motherboard manual on the Internet)
  • 18:37, 25 July 2023 Abby talk contribs posted a new comment on NASPi CM4-M2 (Hi, Please refer to: https://wiki.geekworm.com/File:X515-IMG-5896-6Pin-Headers.jpg Regards, Abby / Geekworm)
  • 18:35, 25 July 2023 37.30.12.1 talk posted a new comment on NASPi Gemini 2.5 (I've got disk failure in RAID1 and I know which disk to replace. Do I have to do something else except of replacing failed disk or the RAID1 will restore itself automatically?)
  • 15:51, 25 July 2023 Harry talk contribs posted a new comment on XScript (Hi, New add #Uninstall secton. But I still recommend you to use the new script. The higher temperature may just be your illusion.)
  • 16:15, 24 July 2023 Harry talk contribs deleted comment #2900 on NASPi Gemini 2.5
  • 16:14, 24 July 2023 Harry talk contribs posted a new comment on NASPi Gemini 2.5 (Refer to How to enable OLED display)
  • 16:12, 24 July 2023 Harry talk contribs posted a new comment on NASPi Gemini 2.5 (Hi, we updated the installation script: XScript)
  • 16:12, 22 July 2023 89.0.119.63 talk posted a new comment on XScript (Hi, how to uninstall this X-Script? Because the temperature now is higher than with the older X-C1-script I used before. Thanks! Achim)
  • 13:52, 22 July 2023 219.165.222.129 talk posted a new comment on PiKVM-A8 (Hello, What is the polarity of the "TO PANEL" connector? Is the pin on the side closest to the board positive or negative? Sorry if I missed the description. Thanks in advance.) Tags: Mobile web edit, Mobile edit
  • 11:26, 22 July 2023 99.51.191.9 talk posted a new comment on PiKVM-A3 (Audio isn't working. Is the I2S cable released? How can I get one?)
  • 01:21, 22 July 2023 89.205.128.94 talk posted a new comment on NASPi CM4-M2 (i would laso like to know if it is possible to power the nass intrrnally so i can have my own 5v supply which i will use to powersome pcie peripherals) Tags: Mobile web edit, Mobile edit
  • 01:11, 22 July 2023 89.205.128.94 talk posted a new comment on NASPi CM4-M2 (I would like to know what the 6 pin header next to the front usb port does. I was guesing/hoping it was for i2c spi and/or uart but i couldnt find anything about it. If this is the case i would also like to know what the pinout of this header is.) Tags: Mobile web edit, Mobile edit
  • 16:44, 19 July 2023 37.170.87.133 talk posted a new comment on X708 (Hi, in the python battery code : def readVoltage(self): address = 0x36 read = self._bus.read_word_data(address, 2) swapped = struct.unpack("<H", struct.pack(">H", read))[0] self.voltage = swapped * 1.25 / 1000 / 16 return self.voltage def readCapacity(self): address = 0x36 read = self._bus.read_word_data(address, 4) swapped = struct.unpack("<H", struct.pack(">H", read))[0] self.capacity = swapped / 256 if...)
  • 09:33, 19 July 2023 159.196.171.123 talk posted a new comment on X-C1 Software (Question: The fan isn't running, likely it's not hot enough, how can I test it is working correctly without waiting until it is hot enough?)
  • 04:46, 19 July 2023 93.81.26.252 talk posted a new comment on Auto Mount an NTFS USB Drive on Raspberry Pi (good manual, tnxalot)
  • 17:36, 17 July 2023 Walker talk contribs posted a new comment on X950 software (Hello, may I ask what problem you encountered? Can you provide your order number? The information on the webpage is of course useful. If you encounter a problem that cannot be solved, you can send an email to us (support@geekworm.com), and you can describe your problem in detail. It is of course best if you can provide a video. We will also try our best to solve the problem for you)
  • 17:28, 17 July 2023 Walker talk contribs posted a new comment on 2.4G wireless Gamepad (Hello, we have stopped selling this product for a long time, and the information of this product is no longer available)
  • 17:19, 17 July 2023 Walker talk contribs posted a new comment on PiKVM-A8 (Hello, we don't know what kind of interface inside the Asus motherboard, this may be related to the type of computer)
  • 16:57, 17 July 2023 Walker talk contribs posted a new comment on X-C1 Software (Hello, we have not tested Home As sistant OS, only some other systems have been tested, you can browse here for details: https://wiki.geekworm.com/XScript)
  • 16:51, 17 July 2023 Walker talk contribs posted a new comment on PiKVM-A3 (Hello, we have updated the RTC instructions. For details, you can check How to enable RTC in the FAQ. Can you try it and see if it works? If it still doesn't work, you can send email to us (support@geekworm.com))
  • 16:32, 17 July 2023 176.126.228.179 talk posted a new comment on X950 software (Would it have been useful to include a link to this webpage on the included paperwork? Even the video on the website - the info doesnt work.)
  • 14:47, 17 July 2023 67.187.26.120 talk posted a new comment on PiKVM-A3 (I tried the RTC instructions above but they didn't seem to work. Please help. [root@pikvm kvmd-webterm]# rw [kvmd-webterm@pikvm ~]$ grep Clock -A 2 /boot/config.txt # Clock #dtoverlay=i2c-rtc,pcf8563 dtoverlay=i2c-rtc,ds1307 [root@pikvm kvmd-webterm]# date Mon Jul 17 09:42:47 MSK 2023 [root@pikvm kvmd-webterm]# hwclock -w hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --verbose option to see the details of our search for an access method.)
  • 04:46, 16 July 2023 174.170.237.57 talk posted a new comment on X306 (Is there a way to interface with the UPS from Linux on the raspberry pi? I would like to use NUT to automatically shutdown the system when the battery reaches a certain percentage)
  • 22:59, 14 July 2023 82.123.46.36 talk posted a new comment on X-C1 Software (Doesn't work under Home Assistant OS on a Raspberry Pi... fan running at fuul speed ans thus very noisy.)
  • 11:09, 14 July 2023 138.199.54.40 talk posted a new comment on PiKVM-A8 (Hello, In your example with the Asus motherboard the connections with the power switch and the reset switch are reversed. Why?)
  • 03:50, 14 July 2023 94.203.203.100 talk posted a new comment on 2.4G wireless Gamepad (hello, Can I outreach the main company that produces these Kind of gamepads ?) Tags: Mobile web edit, Mobile edit
  • 11:08, 12 July 2023 72.90.255.109 talk posted a new comment on X306 (Hi, I'm also having the same problem with the USB ports, none of them are working. They are powering things, but no data goes through. I have confirmed the pogo pins are making contact, and have tried using a USB hub on the pi alone, without the UPS, and the hub works fine, so there's something wrong with this UPS. Does it need a ferrite ring? Would love to solve this issue! Thanks, Evan)
  • 11:38, 11 July 2023 Walker talk contribs posted a new comment on P88 (Hello, the 2.5 mm thick thermal pad will be very soft after tearing off the surface film, you can squeeze it, it will be in contact with the shell, and then the heat dissipation effect will be better)
  • 11:20, 11 July 2023 Walker talk contribs posted a new comment on PiKVM (you can refer to this https://wiki.geekworm.com/PiKVM-A4#FAQ)
  • 11:18, 11 July 2023 Walker talk contribs deleted comment #3814 on PiKVM
  • 11:18, 11 July 2023 Walker talk contribs posted a new comment on PiKVM ({PiKVM-A4#FAQ})
  • 11:08, 11 July 2023 Walker talk contribs posted a new comment on X728-hardware (Hello, we have not tested X728 and PI4 and Mini ATX PSU II assembled together, this may need to be tried by yourself)
  • 10:42, 11 July 2023 Walker talk contribs posted a new comment on X703 (Thank you very much, when using the power supply or battery, we must pay attention to the relevant precautions)
  • 10:28, 11 July 2023 Walker talk contribs posted a new comment on N508 (Thank you for your suggestion, but our current fan design is directly plugged into the GPIO)
  • 10:10, 11 July 2023 Walker talk contribs posted a new comment on PiKVM-A3 (The fan of X630-A3 does not support speed adjustment)
  • 21:47, 9 July 2023 62.212.95.35 talk posted a new comment on NASPi Gemini 2.5 (How exactly does the power button work? It seems that gpio pin 4 does not immediately correspond to button presses (edge raising & falling) as it seems to be buffered to facilitate the long press hard shutdown? Is there maybe a schema how the power button, pin 4 and the power led work together?)
  • 05:55, 9 July 2023 81.143.10.214 talk posted a new comment on P88 (The 2.5mm thick thermal pad was too thick to fit in position A _ the 1mm pad fitted fine and was in contact with the chip and the case.)
  • 00:59, 9 July 2023 75.74.77.189 talk posted a new comment on X450/X5500 Software Configuration (Hello, I selected iqaudio-DAC for the piCore Player but it does not work. When I do aplay -l **** List of PLAYBACK Hardware Devices **** card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1] Subdevices: 4/4 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 Subdevice #2: subdevice #2 Subdevice #3: subdevice #3 card 1: Headphones [bcm2835 Headphones], device 0: bcm2835 Headphones [bcm2835 Headphones] Subdevices: 4/4 Subdevice #0: subdevice #0 Subdevice #1:...)
  • 15:57, 7 July 2023 91.65.17.105 talk posted a new comment on X715 (Can you please provide example for how to use X715 together with X728 (UPS) to achieve 6~60V wide voltage input. I see two options: 1. Stack Raspberry, X715 & X728. - Power in to X715. X715 will power Raspberry directly. - Power cable from X715 to X728. For X728 to charge batteries. 2. Stack Raspberry & X728. X715 separate. - Power in to X715. Fan function not usable as it is not stacked on Raspberry. - Power cable from X715 to X728. X728 charge batteries and provide power to Raspb...)
  • 18:47, 5 July 2023 81.97.209.55 talk posted a new comment on PiKVM (the generic pi2w image is missing i2c-dev & turning it on so add them. -------- cd /etc/modules-load.d/ more kvmd.conf rw nano kvmd.conf dwc2 libcomposite tc358743 i2c-dev cd /boot nano config.txt dtparam=i2c_arm=on systemctl enable --now kvmd-oled kvmd-oled-reboot kvmd-oled-shutdown ro reboot ---------)
  • 16:48, 5 July 2023 81.97.209.55 talk posted a new comment on PiKVM (I just want to know how to make the PiKVM-A4 LCD display work where are the geekworm scrips to do that)
  • 22:46, 3 July 2023 103.43.78.119 talk posted a new comment on Raspi UPS HAT Board (it seems if you short out power switch and dual power connected then it works the way ups does, soon as power is applied battery get charge and pi is up and running then power goes out pi continue running on battery until battery dies, add voltage divider for 5v input power to any GPIO pin to detect power outage. it works the way my needs.)
  • 10:49, 3 July 2023 68.51.90.40 talk posted a new comment on X728-hardware (I just purchased the Mini ATX PSU II - Desktop ATX Power Supply raspberry pi HAT. I currently have the X728 V2.3 on my Pi 4B. How do I stack these units together so I can use ATX power and fallback to the X728 when ATX loses power? I expect maybe needing to do some coding to make them work together software side, but will I be able to use this combination as expected?)
  • 15:37, 1 July 2023 175.116.49.141 talk posted a new comment on X708-Software (x708, x862 (NGFF, WD SA510), two 18650 batteries, and a metal pushbutton switch latching are in use. 1. If this package device is left unused, the battery will be completely discharged. The power switch does not operate when the adapter is connected to the x802 boarder. So when I remove the power cord of the battery holder from the x708 boarder and reconnect it, it charges and works. However, the software does not boot. A Linux file system error and a disk error of M.2 NGFF on this x862 bo...)
  • 19:41, 30 June 2023 77.22.139.218 talk posted a new comment on Properly Mount USB Storage on Raspberry Pi (There is an automounting issue using the AON funtion on the board. I am currently working on this issue to figure out what is the problem.)
  • 18:29, 29 June 2023 Walker talk contribs posted a new comment on P165 (Hello, the metal casing may have a little impact on the WIFI signal, but it will not be very big, and the situation you mentioned should not happen)
  • 12:26, 29 June 2023 148.75.141.239 talk posted a new comment on X703 (Definitely heed the warnings about using the USB-C input on the PI or changing headers while plugged in or having batteries in it. One of mine started smoking immediately. Pull the batteries and everything seems ok now. Just set it up and don't touch it after. Get your pi setup first and add this last.)
  • 11:00, 29 June 2023 73.137.100.242 talk posted a new comment on N508 (Why wasn't the fan designed to take advantage of the 5V fan header adjacent to the RTC Connector?)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"