P252

Overview

This is an aluminum alloy passive cooling case designed for Raspberry Pi 3 Model B+ Plus and Raspberry Pi 3 Model B. This aluminum case have a great heat dissipation with perfect design.

Features

Increasing the large Cooling column allows for better heat dissipation.
Design with good heat dissipation, do not have to install the cooling fan or heatsink.
This case is constructed out of high quality aluminum material.
Suitable for Raspberry Pi 3 Model B+ /3B / 2B motherboard
Easy installation and all hardware is included
Access to all ports of Raspberry Pi 3 Model B+ /3B / 2B
GPIO cable interface is reservered, support to install the gpio cable.
Easy to install and insert the micro sd card

Packing List

1 x Aluminum Case
1 x Screws pack with thermal tapes

User Manual

P252 Installation Video: https://youtu.be/HrttF7HNpb8

How to Use the Thermal Tape for Raspberry Pi 3B+ and Raspberry Pi 3B

with 4pcs thermal tapes to attach on your Raspberry Pi 3B+/3B. For Raspberry Pi 3B+, attach the big thin thermal tape on CPU; For Raspberry Pi 3B, attach the big thick thermal tape on CPU.

Enable comment auto-refresher

Anonymous user #10

2 months ago

Score 0

Using P252 for a portable Pi 3B project. Great design! Long term think about optional dust plugs for unused ports (RJ-45, USB, audio, HDMI). Port for microSD can be covered with quality adhesive rubber or electrical tape.

Permalink | Reply

Anonymous user #9

7 months ago

Score 0

All four screws are the same length, though they should not be as the ones toward the middle of the case stand proud.

Permalink | Reply

Anonymous user #8

18 months ago

Score 0

I have a 3B. In the kit I received there are 6 pads that are all 13mm square and one that is 8mm square. The large ones are 2x2mm 2x1.5mm and 2x.5mm. I assume one of the large ones goes in location 3. Should the 2mm pad go on the CPU on top and the 1.5mm go om the bottom, or the other way around?

Permalink | Reply

Walker

18 months ago

Score 0

Hello, there is an installation guide on the WIKI, which indicates the installation position of each thermal pad, you can take a closer look first

Permalink

Anonymous user #7

19 months ago

Score 0

Geekworm needs to update the packing list and assembly. The kit I just received had 2X 2.0mm thermal pads, 2X 1.5mm, 2X 1.0mm, and 2X 0.5mm. Also, all four screws were the same length.

Permalink | Reply

Walker

19 months ago

Score 0

Hello, the product has been upgraded, and the screws have also been changed. This picture shows the old version of the screws and accessories. Now we are sending the new version of P252 to the customer. The screws and accessories in the new version shall prevail. Thank you

Permalink

Anonymous user #7

19 months ago

Score 0

Geekworm needs to update the packing list and assembly. The kit I just received had 2X 2.0mm thermal pads, 2X 1.5mm, 2X 1.5, 2X 1.0mm, and 2X 0.5mm. Also, all four screws were the same length.

Permalink | Reply

Walker

19 months ago

Score 0

Hello, the product has been upgraded, and the screws have also been changed. This picture shows the old version of the screws and accessories. Now we are sending the new version of P252 to the customer. The screws and accessories in the new version shall prevail. Thank you

Permalink

Anonymous user #6

20 months ago

Score 0

Fits great, but metal lug for IC4 on the 3B+ model is off centre, but still contacts 40% of it. Happy.

Permalink | Reply

Walker

20 months ago

Score 0

Thank you so much

Permalink

Anonymous user #5

22 months ago

Score 0

Very well designed case. I was quite surprised there was access to all rpi3 peripherals including PiCam ribbon. This was not apparent from the Aliexpress images and I was regretting that I should have gone with more common passive cooled cases. However this turns outs o be streets ahead with being fully enclosed yet access to everything. The thermal pads confused me a bit, as I hadn't read this web page then.

Permalink | Reply