X708-Hardware
Jump to navigation
Jump to search
1. Power Jack and Connectors
Power input | 5Vdc +/- 5% , ≥3A |
DC Power Plug Size | 5.5*2.5mm |
USB power in socket | Type-C |
UPS power output | 5.1Vdc 8A |
Power output connector | XH2.54mm 2pin |
- X708 powers the Raspberry Pi via the 40-pin header (Pin 2 & 4)
- Don't power the Raspberry Pi via the Pi's type-C USB socket
- X708 can be powered via the onboard DC jack or Type-C USB power socket
2. 6-Pin Function Header
Jumper Name | Usage |
---|---|
PLD
(Power loss detection) Pin 1&2 |
|
AON
(Auto power-on) Pin 3&4 |
|
ASD
(Auto shutdown) Pin 5&6 |
1. Battery voltage must be >3Vdc 2. Insert the battery into the holder 3. Wait 3 seconds then insert the jumper 4. If the jumper inserted before battery, remove battery & jumper then repeat step 1, 2 and 3.
|
3. How to connector external power switch
Pin No. | Pin Description |
---|---|
1 | Power on/off control connecting to switch |
2 | Ground |
3 | LED+ for battery low indicator |
4 | LED+ for power on, rebooting and shutdown |
4. Power button (Script for power mgnt installed)
Press and Release | Raspberry Pi and X708 turn on |
---|---|
Press and hold for 1~2 seconds | System rebooting |
Press and hold for 3~7 seconds | System shutting down |
Press and hold for >8 seconds | Force shutdown |
5. Function LEDs
LED Name | Usage | ||||
---|---|---|---|---|---|
BAT
LOW |
LED red on indicates battery low (≤3.0Vdc) or blue power button pressed (Jumper for ASD inserted) |
5V OUT || LED green on flashing indicates 5V power out and UPS powered by battery |
AC FAIL || LED red on indicates AC power loss or PSU failure or PSU disconnected |
PWR |
LED blue indicates Stays on - Power on Blinks rapidly - system rebooting Blinks slowly - Shutting down |
6. Fuel gauge - LED Indicator
Operation of Discharging
Capacity C (%) | D1 | D2 | D3 | D4 |
---|---|---|---|---|
C ≥75% | ON | ON | ON | ON |
50%≤C<75% | ON | ON | ON | OFF |
25%≤C<50% | ON | ON | OFF | OFF |
3%≤C<25% | ON | OFF | OFF | OFF |
0%<C<3% | Flashing | OFF | OFF | OFF |
Operation of charging
Capacity C (%) | D1 | D2 | D3 | D4 |
---|---|---|---|---|
Fully charged | ON | ON | ON | ON |
75%≤C | ON | ON | ON | Flashing |
50%≤C<75% | ON | ON | Flashing | OFF |
25%≤C<50% | ON | Flashing | OFF | OFF |
C<25% | Flashing | OFF | OFF | OFF |
7. Pins and GPIO used
Pin No. | Usage |
---|---|
2, 4 | +5V power supply |
3, 5 | I2C for RTC and battery fuel-gauge systems |
6 | Ground |
29 | GPIO5 for power management |
32 | GPIO12 for power management |
33 | GPIO13 for power management |
31 | GPIO6 for AC power loss detection |
(Jumper for PLD inserted, High=power loss, | |
Low=Power supply normal) |
Enable comment auto-refresher
Anonymous user #8
Permalink |
Walker
Anonymous user #15
Permalink |
Lisa
Anonymous user #15
Permalink |
Lisa
Anonymous user #16
Lisa
Anonymous user #14
Permalink |
Anonymous user #13
Anonymous user #14
Anonymous user #13
Permalink |
Lisa
Anonymous user #12
Permalink |
Lisa
Anonymous user #10
Permalink |
Lisa
Anonymous user #10
Permalink |
Lisa
Lisa
Anonymous user #10
Lisa
Anonymous user #9
Permalink |
Lisa
Anonymous user #8
Permalink |
Lisa
Anonymous user #7
Permalink |
Anonymous user #3
Permalink |
Anonymous user #4
Anonymous user #5
Anonymous user #5
Xiali
Anonymous user #2
Permalink |
Anonymous user #5
Anonymous user #6
Anonymous user #11
Anonymous user #1
Permalink |