-
RP2040-Zero: Difference between revisions
| Line 61: | Line 61: | ||
==Use Manual== | ==Use Manual== | ||
'''[https://www.waveshare.com/wiki/RP2040-Zero#Pico_Getting_Started Pico Getting Started]'''（Main link: Official resource page） | |||
* [https://www.waveshare.com/wiki/RP2040-Zero#Resources Resources] | * [https://www.waveshare.com/wiki/RP2040-Zero#Firmware_Download Firmware_Download] | ||
* [https://www.waveshare.com/wiki/RP2040-Zero#Basic_Introduction Basic Introduction] | |||
* [https://www.waveshare.com/wiki/RP2040-Zero#MicroPython_Series MicroPython Series] | |||
* [https://www.waveshare.com/wiki/RP2040-Zero#C.2FC.2B.2B_Series C/C++ Series] | |||
* [https://www.waveshare.com/wiki/RP2040-Zero#Arduino_IDE_Series Arduino IDE Series] | |||
* [https://www.waveshare.com/wiki/RP2040-Zero#Open_Source_Demos Open Source Demos] | |||
'''[https://www.waveshare.com/wiki/RP2040-Zero#Resources Resources]'''（Main link: Official resource page） | |||
[https://www.waveshare.com/wiki/RP2040-Zero#Supporting_Resources Supporting Resources] | |||
[https://www.waveshare.com/wiki/RP2040-Zero#Applications Applications] | |||
[https://www.waveshare.com/wiki/RP2040-Zero#Official_Documents Official Documents] | |||
[https://www.waveshare.com/wiki/RP2040-Zero#Project_Resources Project Resources] | |||
[https://www.waveshare.com/wiki/RP2040-Zero#FAQ Full FAQ](External link to the official FAQ page) | |||
==Dimensions== | ==Dimensions== | ||
Revision as of 14:39, 3 August 2026
Overview
RP2040-Zero is a tiny, low-cost Pico-compatible microcontroller module based on Raspberry Pi RP2040 dual-core chip. Its castellated edge pads allow direct SMD surface mounting for mass production integration.
Two variants available: bare castellated module or pre-soldered pin header model for rapid breadboard prototyping
Technical Specification
| Main Controller | RP2040 dual-core Arm Cortex-M0+, max 133MHz clock |
| Memory | 264KB SRAM, 2MB onboard NOR Flash (W25Q16JVUXIQ) |
| Power Supply | ME621 LDO regulator, max 800mA output; support 5V USB-C power input.
Independent power pins are reserved on board: 5V power input, GND ground, 3.3V power output for external sensor power supply. |
| IO Resources | 29 multi-function GPIO pins, integrated 3-channel ADC, hardware I2C/SPI/UART/PIO peripherals.
All GPIO pads are gold-plated, compatible with both manual soldering and SMT mass production. |
| Onboard Peripherals | USB-C port, BOOT download button, RESET button, WS2812 programmable RGB LED |
| Dimension | 18.00mm × 23.50mm |
Supported Development Environment
| Programming Language | C/C++ SDK, MicroPython |
| Compatible IDE | VS Code, Arduino IDE, Thonny Python Editor |
| Compatible IDE | VS Code, Arduino IDE, Thonny Python Editor |
Pin Definition
Equipped with 29 independently configurable multiplexed GPIO pins. Each single pin can be assigned as digital GPIO, PWM output, ADC analog input, or hardware communication interface (SPI/I2C/UART). Complete pin function allocation details are available in the official pinout diagram.
Use Manual
Pico Getting Started（Main link: Official resource page）
- Firmware_Download
- Basic Introduction
- MicroPython Series
- C/C++ Series
- Arduino IDE Series
- Open Source Demos
Resources（Main link: Official resource page） Supporting Resources Applications Official Documents Project Resources
Full FAQ(External link to the official FAQ page)
Dimensions
FAQ
Q1: Question 1
A: Place the answer here.