Geekworm Wiki

UPS Scap 5V5A: Difference between revisions

← Older editNewer edit →
VisualWikitext
Rita (talk | contribs)
commentadmin, Administrators
624 edits
Rita (talk | contribs)
commentadmin, Administrators
624 edits
No edit summary
Line 22: Line 22:


==Features==
==Features==
* '''8 x SATA 3.0 Ports''' ： Connect up to eight SATA devices simultaneously to your Raspberry Pi 5
* '''High-Capacity Storage''' ： Up to 176TB theoretical total (22TB per drive; compatibility varies)
* Wide Drive Compatibility ： Works with all SATA 6G, 3G, and 1.5G hard drives and SSDs
* Multi-Speed Support ： Supports communication speeds of 5.0, 3.0, and 1.5 Gbit/s
* HDD/SSD status LED: flashing: Solid light for device connected, flashing for read/write activity, off for no device connected.
* Flexible Power Input ： Accepts 12V power via DC jack or ATX 4-pin connector
* '''Unified Power Delivery''' ： High-efficiency DC/DC converter delivers up to 12A to power both Pi 5 and SATA drives from a single source
* '''Pogo Pin Power to Pi 5''' ： Powers your Raspberry Pi 5 directly via pogo pins; no separate power supply needed
* '''Automatic Drive Power Cut-off''' ： Cuts power to SATA devices when Pi 5 shuts down '''(DC jack only; not supported with ATX 4-pin) '''
* Splitter Cable Included ： Comes with a power SATA splitter cable to support up to 8 drives
* '''HAT-Friendly Design''' ： Mounts on the bottom of the Pi 5,  allowing use of standard HATs with no protruding components on the bottom
* '''12V PWM Fan Header'''：  For custom case cooling solutions
* Tested and supported operating systems: Raspberry Pi OS (64-bit), OpenMediaVault (OMV)
* Compatible Accessories: PA12V10A power adapter, X15-F10 8010 PWM-controlled fan
<font color=red>Note:
*The X1017 does not support SATA boot with the current Raspberry Pi5 firmware.
*The X1017 powers the Raspberry Pi 5 via pogo pins. Do not power the Raspberry Pi 5 through its USB-C port
</font>
==Technical Specification==
{| class="wikitable"
{| class="wikitable"
|-
|-
| '''For use with''' ||  
|'''Power input'''||
Raspberry Pi 5 Model B
* '''12Vdc ± 5%'''<font color=red>(Warning: Over-voltage will damage your HDDs!)</font>
*Intput Ripple & Noise: 200mVp-p Max 
|-
|'''Recommended power supply via DC jack'''||
* 8 x SATA 2.5" HDD/SSD : '''12V 10A adapter x1'''
* 4 x SATA 3.5" HDD : '''12V 10A adapter x1'''
* 8 x SATA 3.5" HDD : '''12V 10A adapter x2'''
(Note: 3.5" HDDs draw high inrush current on startup. 8×3.5" HDD setups require two identical-spec 12V DC adapters connected in parallel via the dual DC jacks.)
|-
|-
| '''Key Features''' ||  
|'''Recommended power supply via 4-pin ATX connector'''||
'''UPS Output'''
* '''12V 20A'''
* Provides continuous operation for up to 6 hours (duration depends on battery type and applications)
<font color=red>⚠️ CRITICAL WARNING: Never connect a DC power adapter AND an ATX power supply to the board simultaneously.</font>
* Supports a maximum current output of 5.1V 5000mA, suitable for most Raspberry Pi applications
* Integrated Advanced Power MOSFET with an equivalent of 7mΩ RDS(ON) to minimize power loss
* Convenient pogo pin connection for powering the Pi, eliminating the need for cabling and soldering


'''Battery Charging'''
|-
* Supports fast battery charging with a capacity of 3000mA
| '''Raspberry Pi Power Supply''' || 5.1V ±5%
* Battery charging control can be managed via GPIO
* Provides protection against battery overcurrent and overvoltage
* Built-in protection against reverse connection of battery cells
* Integrated Maxim's fuel-gauge systems for reading battery voltage and percentage over i2c
* On-board LEDs indicate battery charging and discharging levels of 25%, 50%, 75%, and 100%
* Features a 2-cell 18650 battery holder


'''Power Input'''
|-
* Powered through the USB-C socket, eliminating the need to change your power adapter
| '''Ports & Connectors''' ||
*  '''2 × DC 5.5×2.1mm power input jacks''' (parallel design)
* '''1 × ATX 4-pin power in/out connector '''
（Input: powers the whole system when connected to an ATX power supply


'''Enhanced Power Management'''
Output: provides 12V for extra drives when powered via DC jacks）
* Seamless power switching between backup power and power adapter
* 1 × 16-pin 0.5mm pitch PCIe FFC connector
* On-board push button performs the same actions as the Pi's power button
* 8 × 7-pin SATA 3.0 data connectors
* Automatically cuts off power when the Pi is shut down
* 1 × 4-pin function header
* On-board LED indicates power status and Pi detection
|-
* AC power loss and power adapter failure detection via GPIO
| '''4-pin Function Header Pinout'''||
* Auto power-on when power is applied or restored
* Pin1 = external momentary power switch
* Automatic safe shutdown when battery voltage is low (programmable)
* Pin2 = fan PWM (Connecting to Raspberry Pi 5 Fan)
* Ultra-low standby power consumption to maximize battery life
* Pin3 = ground
* Advanced system power-path management to minimize frequent charging and discharging of batteries
* '''Pin4 = 12V power output
 
|-
'''Miscellaneous'''
| '''PCB Size''' || 100mm × 86mm
* Connects to the Pi via convenient pogo pins, eliminating the need for additional cabling
* Designed to be attached on the bottom, allowing the use of favorite HATs alongside it
|-
|-
| '''Spec''' ||  
|'''PCIe cable length'''|| 37mm
<span style="color:red">'''Power&Charge input:''' 5Vdc 5A via USB Type-C of X1200</span>
 
'''UPS output:''' 5.1V ±5% Max 5A
 
'''Battery charging current:''' Max 2.3-3.2A
 
'''Terminal Battery Voltage:''' 4.23V


'''Battery Recharge Threshold:''' 4.1V


'''Ports & Connectors:'''
* USB Type-C socket x1
* 18650 battery socket x2
* 5V Power output connector x2 - XH2.54 2-pin


'''PCB Size:''' 85mm x 56mm
|-
| '''Notes''' ||
* <span style="color:red">Do not apply power to your Raspberry Pi 5 via the Type-C USB socket.</span>
* Do not use 18650 battery with built-in protection circuit.
|}
|}
==Packing List==
==Packing List==
* X1200 UPS shield x 1
* X1200 UPS shield x 1
Retrieved from "https://wiki.geekworm.com/UPS_Scap_5V5A"