Geekworm Wiki

X700: Difference between revisions

← Older editNewer edit →
VisualWikitext
Line 21: Line 21:
! ITEM !! DESCRIPTION
! ITEM !! DESCRIPTION
|-
|-
| FOR USE WITH ||  
| Compatible with||  
*Raspberry Pi 1 Model B+/ 2 Model B / 3 Model B / 3 Model B+
*Raspberry Pi Model B+/ 2 Model B / 3 Model B / 3 Model B+ / 3 Model A+
|-
|-
| OPERATING SYSTEM ||  
| OPERATING SYSTEM ||  
*Moode Audio Player
* Raspbian Stretch
*OSMC
* Safe shutdown function tested for Raspbian, other operating systems to be tested and advised
*Openelec
*Raspbian Jessie
*Volumio
*Pi Core Player
|-
|-
| KEY FEATURES ||  
| KEY FEATURES ||  
*Ideal storage solution for Jetson Nano - 2.5"" SATA HDD/SSD Shield
'''Smart Uninterruptible Power Supply (UPS)'''
*Supports up to 4TB 2.5-inch SATA hard disk drives (HDD) / solid-state drive (SSD)
*Provides continuous operations for up to 10hours (depending on battery type used)
*USB 3.1 Gen1 to SATA 6Gb/s bridge controller
*5.1V 3000mA Power Backup for even the most demanding Pi 3 set ups
*USB 3.1 Gen1 connectivity offers plug-and-play functionality on your Jetson Nano
*18650 dual Cells Lithium Ion Holder
*Quick file transfer with high-speed USB3.1 Gen1 connectivity  from a PC or a Mac
*Can work with single or dual 18650 Lithium Ion battery
*Specially-made USB3.1 bridge to connect with Jetson Nano - no additional cables needed
*Integrated battery protection circuit
*On-board DC power jack allows to provide enough power to HDD/SSD
*Integrated over current protection and over voltage protection
*Intelligent power management - Automatic powering off when system shutdown
*Integrated Maxim's fuel-gauge systems (Reading battery voltage and percentage via i2c)
*With 1 Female to 2 Male DC cable supplied to power both T300 and Jetson Nano
*Intelligent automatic charging and discharging
*USB bus-powered or powered by external power adapter
*On-board 4 green LEDs indicate battery charging and discharging levels of 25%, 50% , 75% and 100%
*LED blue indicator indicates drive status
*On-board red LED show the status of battery charging or fully charged
 
'''Intelligent and safe power management'''
*Equipped with both momentary button and latching switch for easy power control
*Press the momentary button to turn on
*Press the momentary button and hold for 1~2seconds to reboot
*Press the momentary button and hold for 3~7seconds to implement safe shutdown
*Press the momentary button and hold for >8seconds to force shutdown
*Supports safe shutdown and full poweroff through software
*On-board switch convenient to select latching or momentary power control switches
*Press the latching power switch once to turn on and again to implement safe shutdown
*On-board LED shows the status of power on, reboot and shutdown
*On-board PH2.0 connectors allows to use external latching switch or momentary button
*Powers the Raspberry Pi via the 40-pin header - no additional cabling required
*Allows power input via DC jack or Micro-USB socket or XH2.54 connector
*Allows power output via XH2.54 socket and or the 40-pin header
 
'''Other'''
*Reserved 40-pin stackable Header for Add-On Boards
*Powers the Raspberry Pi via the 40-pin header - no additional cabling required
*Works with all current models of the Raspberry Pi using a 40 pin header
*On-board DC jack (5.5*2.5mm) and micro-USB socket convenient for power input
*On-board connector allowing to connect external power switch and DIY your perfect case
|-
|-
| Specification ||  
| Specification ||  
*Power supply: 6-26Vdc，≥3A recommended
*Power supply: 5.1Vdc，2.5~4A
*GPIO used : LRCK - IO19, BCK - IO18, DATA - IO21, IR - IO26, AMP mute - IO22
*UPS output: 5.1V 3A
*Analog audio input level via onboard headphone jack : 2V RMS
*UPS charging current: 2.5A
*Amplifier max output power: 2×100W at 4Ω BTL Load at 21Vdc
*18650 Battery Request: battery voltage: 3.7V-4.2V and without protect circuit
*Resolution/Sampling Rate: upto 24bit / 192KHz (Raspberry Pi I2S)
*Recharge Threshold: 3.99V
*PCB size 87 x 56mm
|-
| DIMENSION ||
*PCB Size: 123mm x 79mm
|-
|-
|  NOTE ||  
|  NOTE ||  
<span class="tb_red">*WARNING: Do not apply power to your Raspberry Pi via the PI's Micro USB socket.</span>
<span class="tb_red">*WARNING:</span>
<span class="tb_red">**DO NOT APPLY POWER TO YOUR RASPBERRY PI VIA THE PI's MICRO USB SOCKET.</span>
<span class="tb_red">**DO NOT APPLY POWER TO X700 VIA THE X820's MICRO USB SOCKET AND DC JACK AT THE SAME TIME.</span>
<span class="tb_red">**DO NOT USE 18650 BATTERY WITH BUILT-IN PROTECTION CIRCUI</span>
|}
|}


Retrieved from "https://wiki.geekworm.com/X700"