X1017: Difference between revisions

(3 intermediate revisions by 2 users not shown)

Line 3:

*Never connect a DC ~~power~~ adapter ~~AND~~ an ATX power supply to the board ~~simultaneously~~. ~~This~~ will permanently ~~destroy~~ the board and connected devices.

* Never connect both a DC adapter and an ATX power supply to the board at the same time. Doing so will permanently damage the board and any connected devices.

* Do not ~~apply~~ power to your Raspberry ~~Pi via the Type~~-C ~~USB socket~~.

* Do not power your Raspberry Pi5 through its USB-C port while using this board. Use the X1017 as the sole power source for your Pi.

* ~~Warning: Over-voltage will damage your HDD. Please use~~ a stable 12V power supply within the specified range.

* Use a stable 12V power supply within the specified range. Over-voltage will damage your hard drives.

* The X1017 is designed for data storage purposes and does not currently support booting from HDD/SSD with the existing firmware.

* ~~Automatic Drive~~ Power Cut-off: ~~Supported with~~ DC jack ~~power input only~~. ~~Not~~ available when using ATX 4-pin connector.

* Auto Power Cut-off (for drives): This feature works only when powered via the DC jack. It is not available when using the ATX 4-pin connector.

* All SATA ports share the Pi 5's PCIe Gen3 x1 total bandwidth. No impact on HDDs; only affects multi-SSD full-load scenarios.</font>

Line 26:

==Features==

* '''8 x SATA 3.0 Ports''' ： Connect up to eight SATA devices simultaneously to your Raspberry Pi 5

* '''High-Capacity Storage''' ： ~~Supports up~~ to 176TB total ~~capacity~~ (22TB per drive).

* '''High-Capacity Storage''' ： Up to 176TB theoretical total (22TB per drive; compatibility varies)

* Wide Drive Compatibility ： Works with all SATA 6G, 3G, and 1.5G hard drives and SSDs

* Multi-Speed Support ： Supports communication speeds of 5.0, 3.0, and 1.5 Gbit/s

Line 105:

==Packing List==

* X1017 V1.0 PCIe3.0 to 8-port SATA expansion board x1

* Screw M2.5x5mm x4

* Screw CM2.5x5mm x4

* PCIe FFC cable 37mm x2

* SATA power spillter cable x1

@@ Line 3: / Line 3: @@
 <font color=red>
-*Never connect a DC power adapter AND an ATX power supply to the board simultaneously. This will permanently destroy the board and connected devices.
+* Never connect both a DC adapter and an ATX power supply to the board at the same time. Doing so will permanently damage the board and any connected devices.
-* Do not apply power to your Raspberry Pi via the Type-C USB socket.
+* Do not power your Raspberry Pi5 through its USB-C port while using this board. Use the X1017 as the sole power source for your Pi.
-* Warning: Over-voltage will damage your HDD. Please use a stable 12V power supply within the specified range.
+* Use a stable 12V power supply within the specified range. Over-voltage will damage your hard drives.
 * The X1017 is designed for data storage purposes and does not currently support booting from HDD/SSD with the existing firmware.
-* Automatic Drive Power Cut-off: Supported with DC jack power input only. Not available when using ATX 4-pin connector.
+* Auto Power Cut-off (for drives): This feature works only when powered via the DC jack. It is not available when using the ATX 4-pin connector.
 * All SATA ports share the Pi 5's PCIe Gen3 x1 total bandwidth. No impact on HDDs; only affects multi-SSD full-load scenarios.</font>
@@ Line 26: / Line 26: @@
 ==Features==
 * '''8 x SATA 3.0 Ports''' ： Connect up to eight SATA devices simultaneously to your Raspberry Pi 5
-* '''High-Capacity Storage''' ： Supports up to 176TB total capacity (22TB per drive).
+* '''High-Capacity Storage''' ： Up to 176TB theoretical total (22TB per drive; compatibility varies)
 * Wide Drive Compatibility ： Works with all SATA 6G, 3G, and 1.5G hard drives and SSDs
 * Multi-Speed Support ： Supports communication speeds of 5.0, 3.0, and 1.5 Gbit/s
@@ Line 105: / Line 105: @@
 ==Packing List==
 * X1017 V1.0 PCIe3.0 to 8-port SATA expansion board x1
-* Screw M2.5x5mm x4
+* Screw CM2.5x5mm x4
 * PCIe FFC cable 37mm x2
 * SATA power spillter cable x1