X1017: Difference between revisions

(4 intermediate revisions by the same user not shown)

Line 5:

*Never connect a DC power adapter AND an ATX power supply to the board simultaneously. This will permanently destroy the board and connected devices.

* Do not apply power to your Raspberry Pi via the Type-C USB socket.

* ~~WARNIN~~: Over-voltage ~~OR excessive ripple~~ will ~~permanently~~ damage your ~~HDDs/SSDs~~. ~~Use~~ a stable 12V power supply within the specified range.

* Warning: Over-voltage will damage your HDD. Please use a stable 12V power supply within the specified range.

*When using the ATX connector for power output, follow standard Molex current ratings (max 5A per 12V pin for long-term stability) to avoid connector overheating.

* The X1017 is designed for data storage purposes and does not currently support booting from HDD/SSD with the existing firmware.

* Automatic Drive Power Cut-off: Supported with DC jack power input only. Not available when using ATX 4-pin connector.

*All SATA ports share the Pi 5's PCIe Gen3 x1 total bandwidth. No impact on HDDs; only affects multi-SSD full-load scenarios.

* All SATA ports share the Pi 5's PCIe Gen3 x1 total bandwidth. No impact on HDDs; only affects multi-SSD full-load scenarios.

==Overview==

Line 47:

Line 46:

|-

|'''Power input'''||

* '''12Vdc ± 5%'''(Warning: Over-voltage ~~OR excessive ripple~~ will ~~permanently~~ damage your HDDs~~/SSDs.~~)

* '''12Vdc ± 5%'''(Warning: Over-voltage will damage your HDDs!)

*Intput Ripple & Noise: 200mVp-p Max

|-

Line 61:

Line 60:

|-

| '''Raspberry Pi Power Supply''' || 5.1V ±5%~~, maximum 12A (output via spring pin)~~

| '''Raspberry Pi Power Supply''' || 5.1V ±5%

|-

@@ Line 5: / Line 5: @@
 *Never connect a DC power adapter AND an ATX power supply to the board simultaneously. This will permanently destroy the board and connected devices.
 * Do not apply power to your Raspberry Pi via the Type-C USB socket.
-* WARNIN: Over-voltage OR excessive ripple will permanently damage your HDDs/SSDs. Use a stable 12V power supply within the specified range.
+* Warning: Over-voltage will damage your HDD. Please use a stable 12V power supply within the specified range.
-*When using the ATX connector for power output, follow standard Molex current ratings (max 5A per 12V pin for long-term stability) to avoid connector overheating.
 * The X1017 is designed for data storage purposes and does not currently support booting from HDD/SSD with the existing firmware.
 * Automatic Drive Power Cut-off: Supported with DC jack power input only. Not available when using ATX 4-pin connector.
-*All SATA ports share the Pi 5's PCIe Gen3 x1 total bandwidth. No impact on HDDs; only affects multi-SSD full-load scenarios.</font>
+* All SATA ports share the Pi 5's PCIe Gen3 x1 total bandwidth. No impact on HDDs; only affects multi-SSD full-load scenarios.</font>
 ==Overview==
@@ Line 47: / Line 46: @@
 |-
 |'''Power input'''||
-* '''12Vdc ± 5%'''<font color=red>(Warning: Over-voltage OR excessive ripple will permanently damage your HDDs/SSDs.)</font>
+* '''12Vdc ± 5%'''<font color=red>(Warning: Over-voltage will damage your HDDs!)</font>
 *Intput Ripple & Noise: 200mVp-p Max
 |-
@@ Line 61: / Line 60: @@
 |-
-| '''Raspberry Pi Power Supply''' || 5.1V ±5%, maximum 12A (output via spring pin)
+| '''Raspberry Pi Power Supply''' || 5.1V ±5%
 |-