X1207: Difference between revisions

(14 intermediate revisions by 7 users not shown)

Line 3:

[[File:X1207-IMG-0073.jpg|thumb|right|X1207 V1.2]]

[[File:X1207-IMG-0101-pogo-pin-connection.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]

[[File:X1207-IMG-0105.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]

[[File:X1207-IMG-0105-Power.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]

[[File:X1207-IMG-0077.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]

[[File:X1207-IMG-0099.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]

==Safety Instructions & Warnings==

~~'''⚠''' The default charging current is set to 1.5A and charge cut-off voltage is 4.23V. before installing your battery in the~~ UPS board, Please carefully confirm the maximum charging current and voltage, exceeding the upper limit of the charging specification that the battery can withstand will not only cause adverse reactions, but may also cause irreversible damage.

~~'''⚠''' It is essential to read and understand these safety instructions and warnings before charging your batteries.~~

'''⚠''' Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.

'''⚠''' Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".

~~'''⚠''' Do not mix and use old batteries with new batteries, or batteries with different brand names.~~

'''⚠''' Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.

~~'''⚠''' When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material or carpet unattended.~~

~~'''⚠''' Keep the UPS shield away from children to ensure their safety.~~

==Overview==

Line 73:

Line 59:

* [[X1002]] single NVMe shield for Pi5

* [[X1005]] dual NVMe shield for Pi5

* [[X1006]] PCIe to SATA 2.5 HDD+M.2 SSD shield for Pi 5

* [[X1007]] PCIe to dual SATA 2.5 HDD/SSD shield for Pi 5

* [[X1100]] USB3 to SATA 2.5 HDD/SSD shield for Pi 5

* Other add-on boards are attached to the bottom of the Raspberry Pi

|-

| '''Notes''' ||

Line 113:

Line 95:

==User Manual==

* '''Hardware Installation: [https://suptronics.com/Raspberrypi/Power_mgmt/x1207-v1.2_hardware.html X1207 Hardware]''', You can view the '''Raspberry Pi GPIO used''' and '''Dimensions''' here

* '''How to make it work: [~~https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1207 Software~~]'''

* '''How to make it work: [[#Script Reference]]'''

==Packing List==

Line 122:

Line 104:

[[File:X1207-IMG-0015-Packing-List.jpg|600px]]

==Script Reference==

==Installation Guide==

*Installation of X1207 and [[X1207-C1]]

:[[File:X1207-X1207-C1-Install-guide.jpg|800px]]

Installation Video for Raspberry Pi 5+[[X1207]]+[[X1207-C1]]: https://youtu.be/Xorg8pj33yM

==Matching Case==

The [[X1207-C1]] is a premium metal case specially designed for the Raspberry Pi 5 X1207/'''[[X1208]]''' UPS Shield, offering robust protection in a sleek, black aesthetic.

* Case dimension: 92.8 x 90.8 x 42.8 mm

X1207-C1 ~~with Raspberry Pi 5~~-~~Front~~

~~[[001-~~X1207-C1-IMG-0167.jpg|~~Interface~~-~~Front]]~~

X1207-C1-IMG-0165-Packing List.jpg|X1207-C1 Accessories

~~002~~-X1207-C1-IMG-~~0165-Packing List~~.jpg|X1207-C1 ~~Accessories~~

X1207-C1-IMG-0167.jpg|X1207-C1

X1207-C1-IMG-0170.jpg|X1207-C1

X1207-C1-IMG-0174.jpg|X1207-C1

</gallery>

Line 144:

Line 140:

<~~comments~~ />

<comment-streams id="main" />

@@ Line 3: / Line 3: @@
 [[File:X1207-IMG-0073.jpg|thumb|right|X1207 V1.2]]
 [[File:X1207-IMG-0101-pogo-pin-connection.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
-[[File:X1207-IMG-0105.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
+[[File:X1207-IMG-0105-Power.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
 [[File:X1207-IMG-0077.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
 [[File:X1207-IMG-0099.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
 ==Safety Instructions & Warnings==
-'''⚠'''	<span class="tb_red">The default charging current is set to 1.5A and charge cut-off voltage is 4.23V. before installing your battery in the UPS board, Please carefully confirm the maximum charging current and voltage, exceeding the upper limit of the charging specification that the battery can withstand will not only cause adverse reactions, but may also cause irreversible damage.
+{{UPS Safety Warning}}
-'''⚠'''	<span class="tb_red">It is essential to read and understand these safety instructions and warnings before charging your batteries.
-'''⚠'''	<span class="tb_red">Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal   injury, and damage to property if charged or used improperly.
-'''⚠'''	<span class="tb_red">Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the   battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".
-'''⚠'''	<span class="tb_red">Do not mix and use old batteries with new batteries, or batteries with different brand names.
-'''⚠'''	<span class="tb_red">Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when   they are two years old, whichever comes first.
-'''⚠'''	<span class="tb_red">When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material   or carpet unattended.
-'''⚠'''	<span class="tb_red">Keep the UPS shield away from children to ensure their safety.
 ==Overview==
@@ Line 73: / Line 59: @@
 * [[X1002]] single NVMe shield for Pi5
 * [[X1005]] dual NVMe shield for Pi5
-* [[X1006]] PCIe to SATA 2.5 HDD+M.2 SSD shield for Pi 5
-* [[X1007]] PCIe to dual SATA 2.5 HDD/SSD shield for Pi 5
-* [[X1100]] USB3 to SATA 2.5 HDD/SSD shield for Pi 5
-* Other add-on boards are attached to the bottom of the Raspberry Pi
 |-
 | '''Notes''' ||
@@ Line 113: / Line 95: @@
 ==User Manual==
 * '''Hardware Installation: [https://suptronics.com/Raspberrypi/Power_mgmt/x1207-v1.2_hardware.html X1207 Hardware]''', <span class="tb_red"> You can view the '''Raspberry Pi GPIO used''' and '''Dimensions''' here </span>
-* '''How to make it work: [https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1207 Software]'''
+* '''How to make it work: [[#Script Reference]]'''
 ==Packing List==
@@ Line 122: / Line 104: @@
 [[File:X1207-IMG-0015-Packing-List.jpg|600px]]
+==Script Reference==
+{{X120x Series UPS Script Reference}}
+==Installation Guide==
+*Installation of X1207 and [[X1207-C1]]
+:[[File:X1207-X1207-C1-Install-guide.jpg|800px]]
+Installation Video for Raspberry Pi 5+[[X1207]]+[[X1207-C1]]: https://youtu.be/Xorg8pj33yM
+{{#ev:youtube|https://youtu.be/Xorg8pj33yM}}
 ==Matching Case==
 The [[X1207-C1]] is a premium metal case specially designed for the Raspberry Pi 5 X1207/'''[[X1208]]''' UPS Shield, offering robust protection in a sleek, black aesthetic.
 * Case dimension: 92.8 x 90.8 x 42.8 mm
 <gallery>
-X1207-C1 with Raspberry Pi 5-Front
-[[001-X1207-C1-IMG-0167.jpg|Interface-Front]]
+X1207-C1-IMG-0165-Packing List.jpg|X1207-C1 Accessories
--X1207-C1-IMG-0165-Packing List.jpg|X1207-C1 Accessories
+X1207-C1-IMG-0167.jpg|X1207-C1
+X1207-C1-IMG-0170.jpg|X1207-C1
+X1207-C1-IMG-0174.jpg|X1207-C1
 </gallery>
@@ Line 144: / Line 140: @@
 <!--Add review function! -->
-<comments />
+<comment-streams id="main" />
 <!--Please choose the  -->