Geekworm Wiki

X1207: Difference between revisions

← Older edit
VisualWikitext
Lisa (talk | contribs)
commentadmin, Administrators
795 edits
Replace <comments/> with <comment-streams />
 
(55 intermediate revisions by 7 users not shown)
Line 1: Line 1:
{{GD Template Impl}}
[[File:X1207-IMG-9926-Interface-1.jpg|thumb|right|X1207 V1.2 Interface Schematic]]
[[File:X1207-IMG-0073.jpg|thumb|right|X1207 V1.2]]
[[File:X1207-IMG-0101-pogo-pin-connection.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
[[File:X1207-IMG-0105-Power.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
[[File:X1207-IMG-0077.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
[[File:X1207-IMG-0099.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
==Safety Instructions & Warnings==
==Safety Instructions & Warnings==
* <span class="tb_red">You must read these safety instructions and warnings before charging your batteries.
{{UPS Safety Warning}}
* <span class="tb_red">Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the below instructions may result in fire, personal injury and damage to property if charged or used improperly. 
* <span class="tb_red">Never make wrong polarity connection when charging and discharging battery packs. Always double check polarity of battery's connector to make sure "+" to "+" and "-" to "-". 
* <span class="tb_red">Do not mix and use old batteries and new batteries, or batteries with different brand names. 
* <span class="tb_red">Lithium batteries has it's cycle life, please replace old battery with new one when it reaches it's service life or when it is two year old, whichever comes first. 
* <span class="tb_red">When charging Battery Pack, please put battery in a fire proof container. Please don't leave the UPS shield on the wood material or carpet and unattended.


==Overview==
==Overview==
The X1207 is a PoE-powered UPS HAT designed for Raspberry Pi 5, delivering reliable 5.1V/5A backup power to maintain uninterrupted operation. It supports high-demand setups and complies with IEEE 802.3af/at PoE standards, drawing up to 25W from a compatible POE switch while providing both power and network connectivity over a single cable.
The '''X1207''' is a PoE-powered UPS HAT designed for Raspberry Pi 5, delivering reliable 5.1V/5A backup power to maintain uninterrupted operation. It supports high-demand setups and complies with '''IEEE 802.3af/at''' PoE standards, drawing up to 25W from a compatible POE switch while providing both power and network connectivity over a single cable.


With intelligent power management, it monitors Pi status, cuts power after shutdown to conserve battery, and features ultra-low standby consumption. The board ensures seamless power switching during outages and supports auto power-on and AC loss detection.
With intelligent power management, it monitors Pi status, cuts power after shutdown to conserve battery, and features ultra-low standby consumption. The board ensures seamless power switching during outages and supports auto power-on and AC loss detection.
{{Raspberry Pi 5 UPS Sets}}


==Features==
==Features==
{| class="wikitable"
|-
|'''For use with''' || Raspberry Pi 5 Model B
|-
| '''UPS Output''' ||
* Built for continuous, long-lasting operation -providing unwavering power for always-on Raspberry Pi systems
* Supports a maximum current output of 5.1V 5000mA, suitable for most Raspberry Pi applications
* Integrated Advanced Power MOSFET with an equivalent of 7mΩ RDS(ON) to minimize power loss
* Power the Pi directly through the 40-pin header, eliminating the need for cables and soldering
|-
| '''Battery Charging''' ||
* Supports battery charging with a capacity of 1500mA
* Battery charging control can be managed via GPIO
* Provides protection against battery overcurrent and overvoltage
* Built-in protection against reverse connection of battery cells
* Integrated Maxim's fuel-gauge systems for reading battery voltage and percentage over i2c
* On-board LEDs indicate battery charging and discharging levels of 25%, 50%, 75%, and 100%
* Features a single 21700 battery holder, supporting battery of up to 5000mAh
|-
|'''Power Input'''||
* Supports Power over Ethernet (PoE) input capability
* Provides up to 5A output current, enabling 1.5A charging while powering the system
* Standard Compliance: IEEE 802.3af & 802.3at (PoE+)
* Fully isolated switched-mode power supply (SMPS) topology
* Simplified single-cable installation and robust power delivery for Raspberry Pi
* Compatible with Raspberry Pi USB-C Power Supply
|-
|'''Enhanced Power Management'''||
* Seamless power switching between backup power and power adapter
* On-board push button performs the same actions as the Pi's power button
* Automatically cuts off power when the Pi is shut down
* On-board LED indicates power status and Pi detection
* AC power loss and power adapter failure detection via GPIO
* Auto power-on when power is applied or restored
* Automatic safe shutdown when battery voltage is low (programmable)
* Ultra-low standby power consumption to maximize battery life
* Advanced system power-path management to minimize frequent charging and discharging of batteries
|-
|'''Compatible Accessories'''||
* [[X1002]] single NVMe shield for Pi5
* [[X1005]] dual NVMe shield for Pi5
|-
| '''Notes''' ||
* <span style="color:red"> '''DON'T apply''' power to your Raspberry Pi 5 via the Type-C USB socket.</span>
* <span style="color:red">Compatible with unprotected 21700 battery only (Max. length: 70.3 mm).
|}


==Technical specification==
==Technical specification==
Line 21: Line 72:
*5Vdc 5A via USB-C
*5Vdc 5A via USB-C
|-
|-
| '''UPS output''' || 5.1V ±5% Max 5A
| '''UPS output''' ||  
*5.1V ±5% Max 5A
|-
|-
| '''Battery charging current''' || 1.5A
| '''Battery charging current''' ||  
*1.5A
|-
|-
| '''Terminal Battery Voltage''' || 4.23V
| '''Terminal Battery Voltage''' ||  
*4.23V
|-
|-
| '''Battery Recharge Threshold''' || 4.1V
| '''Battery Recharge Threshold''' ||  
*4.1V
|-
|-
| '''Ports & Connectors''' ||
| '''Ports & Connectors''' ||
Line 35: Line 90:
*40-pin extended GPIO header x1
*40-pin extended GPIO header x1
|-
|-
| '''PCB Size''' || 86.5mm x 84.5mm
| '''PCB Size''' ||
*86.5mm x 84.5mm
|}
|}
==User Manual==
* '''Hardware Installation: [https://suptronics.com/Raspberrypi/Power_mgmt/x1207-v1.2_hardware.html X1207 Hardware]''', <span class="tb_red"> You can view the '''Raspberry Pi GPIO used''' and '''Dimensions''' here </span>
* '''How to make it work: [[#Script Reference]]'''


==Packing List==
==Packing List==
Line 44: Line 103:
*Pogo pin x 1 (For connecting to the Pi 5 PSW through hole)
*Pogo pin x 1 (For connecting to the Pi 5 PSW through hole)


==User Manual==
[[File:X1207-IMG-0015-Packing-List.jpg|600px]]
 
==Script Reference==
{{X120x Series UPS Script Reference}}
 
==Installation Guide==
*Installation of X1207 and [[X1207-C1]]
:[[File:X1207-X1207-C1-Install-guide.jpg|800px]]
 
Installation Video for Raspberry Pi 5+[[X1207]]+[[X1207-C1]]: https://youtu.be/Xorg8pj33yM
{{#ev:youtube|https://youtu.be/Xorg8pj33yM}}
 
==Matching Case==
The [[X1207-C1]] is a premium metal case specially designed for the Raspberry Pi 5 X1207/'''[[X1208]]''' UPS Shield, offering robust protection in a sleek, black aesthetic.
* Case dimension: 92.8 x 90.8 x 42.8 mm
 
<gallery>
 
X1207-C1-IMG-0165-Packing List.jpg|X1207-C1 Accessories
X1207-C1-IMG-0167.jpg|X1207-C1
X1207-C1-IMG-0170.jpg|X1207-C1
X1207-C1-IMG-0174.jpg|X1207-C1
 
</gallery>


==FAQ==
==FAQ==
<!-- 这里提供了一个Q&A的模板，增加Q&A时按照下面的格式写就可以了 -->
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q1: Question 1
</div>
<div class="mw-collapsible-content">
A: Place the answer here.
</div>
</div>
<!--Add review function! -->
<comment-streams id="main" />
<!--Please choose the  -->
<!--Remove other categories, just keep the appropriate categories -->
[[Category:Product Manual]]
[[Category:Raspberry pi]]
Retrieved from "https://wiki.geekworm.com/X1207"