203
edits
Changes
{{GD Template Impl}}
[[File:X1502-IMG-9564-Interface.jpg|thumb|right|X1502 Interface]]
[[File:X1502-IMG-9564.jpg|thumb|right|X1502 V1.0 IO Board-front]]
[[File:X1502-IMG-9566.jpg|thumb|right|X1502 V1.0 IO Board-rear]]
[[File:X1502-IMG-9573.jpg|thumb|right|X1502 front view]]
[[File:X1502-IMG-9579.jpg|thumb|right|X1502 rear view]]
[[File:X1502-IMG-9582.jpg|thumb|right|X1502 shield]]
[[File:X1502-IMG-9575.jpg|thumb|right|X1502 shield]]
[[File:X1502-IMG-9566-SSD.jpg|thumb|right|X1502 SSD Support]]
[[File:X1502-IMG-9565.jpg|thumb|right|X1502 Assembly]]
==Overview==
* '''4 x M.2 2280 NVMe SSD Slots''': Supports up to 16TB (4TB x4) via PCIe 2.0 (5Gbps) for fast data transfers and boot times, compatible with M.2 NVMe SSDs in 2280, 2242, and 2230 form factors.
* '''Dual HDMI 2.0 Ports''': Enables dual 4K display output for multimedia or industrial use cases.
* '''Dual MIPI DSI/CSI-2 Connectors''': 22-pin FPC connectors (0.5mm pitch) compatible with Raspberry Pi 5 CSI and DSI modules for seamless camera and display integration.CAM/DISP 0 supports both displays or cameras. CAM/DISP 0 supports using a signal to power down the camera to save power. CAM/DISP 1 typically needs two jumpers fitting to '''J6''' to route the I2C signals from the GPIO connector to the camera connector. CAM/DISP 1 can be used with displays and cameras. If it is used with a camera, it isn’t possible to power down the camera. Also refer to [https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf Raspberry Pi Compute Module 5 IO Board datasheet (Page 5)]
* '''MicroSD Card Slot''': Supports Compute Module 5 Lite variants (without onboard eMMC).
* '''Raspberry Pi HAT+ Compatibility''': Reuse existing Raspberry Pi HATs to save time and reduce development costs.
| '''Technical Specification''' ||
<span class="tb_red">'''Power supply''': </span>
* <span class="tb_red"> 12Vdc +/-5% 5A5A_(It supports 9-17V power input, but we highly recommend 12V)</span>
<span class="tb_red">*</span><span class="tb_red">For optimal performance and device safety, please use the included 12V/5A power supply. Low-quality power sources with excessive output ripple noise may cause permanent damage to both your board and CM5 module.</span>
|}
==User Manual==
* The hardware design refers to the official design, please refer to: https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf
* '''Hardware Installation: [https://suptronics.com/Raspberrypi/cm5/x1502-v1.0_hardware.html X1502 Hardware]''', <span class="tb_red">'''please click the left link to view it, it's very important!''' </span>
* '''How to make it work: [https://suptronics.com/Raspberrypi/cm5/x1502-v1.0_software.html X1502 Software]''', <span class="tb_red">'''please click the left link to view it, it's very important!''' </span>
* You can also refer to the [https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf official CM5 IO board] of the Raspberry Pi Foundation. The usage of X1502 is the same as it.
* https://smarthomecircle.com/how-to-install-os-on-raspberry-pi-compute-module-5-emmc-storage
* how to flash os into cm5 emmc, Refer to the following:
#https://smarthomecircle.com/how-to-install-os-on-raspberry-pi-compute-module-5-emmc-storage
#https://www.youtube.com/watch?v=SWv-WYlHJWQ
* Configuration steps for using an external antenna:
https://www.raspberrypi.com/documentation/computers/compute-module.html#antenna
==Packing List==
[[File:X1502-IMG-9564-Packing-List.jpg|600px]]
==User ManualMatching Case==* Hardware Installation: [https://suptronics.com/Raspberrypi/cm5/x1502The Geekworm X1502-v1.0_hardware.html C1 sheet metal case is designed for Raspberry Pi Compute Module 5 (CM5) and compatible with X1502 Hardware], '''please click the left link to view it, and it's very important!'''* How to make it work: [https://suptronics.com/Raspberrypi/cm5/x1502[X15-v1.0_software.html X1502 SoftwareF1]], '''please click the left link to view it, cooling fan and it's very important!'''* You can also refer to the [https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf official CM5 IO board[C519]] of the Raspberry Pi Foundationcooler. The usage of X1502 is the same as Made from durable sheet metal, itprovides solid protection and excellent passive cooling.* https://smarthomecirclePrecision cutouts allow easy access to all ports, making it ideal for DIY projects, development, or industrial applications.com/how-to-install-os-on-raspberry-pi-compute-module-5-emmc-storage* how to flash os into cm5 emmc, Refer to the following:#https[[File://smarthomecircle.com/how-to-install-os-on-raspberry-piX1502-computeC1-moduleIMG-59876-emmcPacking-storage#https://wwwList.youtube.com/watch?v=SWv-WYlHJWQjpg|600px]]
==FAQ==
<div class="mw-collapsible-content">
A: No, The X1502 does not support Hailo AI acceleration module with the '''current CM5 firmware'''.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q: How to configure for an external antenna?
</div>
<div class="mw-collapsible-content">
A: When using an external antenna, you need to configure the device accordingly. Please follow the official Raspberry Pi documentation for the configuration steps:
https://www.raspberrypi.com/documentation/computers/compute-module.html#antenna
[[File:Antenna-configuration.jpg|none|Antenna Configuration]]
</div>
</div>