3,294
edits
Changes
* '''Dual HDMI 2.0 Ports''': Enables dual 4K display output for multimedia or industrial use cases.
* '''Dual USB 3.2 Gen 1 Ports''': delivering high-speed data transfer rates of up to 5 Gbps.
* '''Dual MIPI DSI/CSI-2 Connectors''': 22-pin FPC connectors (0.5mm pitch) compatible with Raspberry Pi 5 CSI and DSI modules for seamless camera and display integration.CAM/DISP 0 supports both displays or cameras. CAM/DISP 0 supports using a signal to power down the camera to save power. CAM/DISP 1 typically needs two jumpers fitting to '''J6''' to route the I2C signals from the GPIO connector to the camera connector. CAM/DISP 1 can be used with displays and cameras. If it is used with a camera, it isn’t possible to power down the camera. Also refer to [https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf Raspberry Pi Compute Module 5 IO Board datasheet (Page 5)]
* '''MicroSD Card Slot''': Supports Compute Module 5 Lite variants (without onboard eMMC).
* '''Raspberry Pi HAT+ Compatibility''': Reuse existing Raspberry Pi HATs to save time and reduce development costs.
<span class="tb_red">*</span> <span class="tb_red">For optimal performance, please use the official Raspberry Pi 27W USB-C or Geekworm Power Supply. An incompatible power supply may fail to power on the system.</span>
|}
==User Manual==
* The hardware design refers to the official design, please refer to: https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf
* Hardware Installation: [https://suptronics.com/Raspberrypi/cm5/x1507-v1.0_hardware.html X1507 Hardware], '''please click the left link to view it, and it's very important!'''
* How to make it work: [https://suptronics.com/Raspberrypi/cm5/x1507-v1.0_software.html X1507 Software], '''please click the left link to view it, and it's very important!'''
* You can also refer to the [https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf official CM5 IO board] of the Raspberry Pi Foundation. The usage of X1502 is the same as it.
* https://smarthomecircle.com/how-to-install-os-on-raspberry-pi-compute-module-5-emmc-storage
* how to flash os into cm5 emmc, Refer to the following:
#https://smarthomecircle.com/how-to-install-os-on-raspberry-pi-compute-module-5-emmc-storage
#https://www.youtube.com/watch?v=SWv-WYlHJWQ
* Configuration steps for using an external antenna:
https://www.raspberrypi.com/documentation/computers/compute-module.html#antenna
==Test & Reviews==
Test Conditions
-System board details: Raspberry Pi Compute Module 5 Lite 2GB RAM
-Interface board details: X1507 CM5 IO boards
-Operation system: Raspberry Pi OS with desktop (Debian12 (bookworm), 64bit, Release date: May 13 2025) openmediavault 7.0
-Storage details: SKhynix HFM128GD3HX015N 128G, KIOXA KBG40ZMT128G 128G
- Nework details: Xiaomi WiFi7 router BE6500
- Ambient temperature: 28°C
Thermal performance with the supplied passive cooler: After 10 minutes in standby, the CPU temperature reaches 37.5°C.
[[File:Cpu-temp_standby.png|600px]]
Under a 10-minute stress test, the CPU stabilizes at 57.3°C.
[[File:Cpu-temp_stress.png|600px]]
Under a 30-minute stress test, the CPU stabilizes at 57.3°C.
[[File:Cpu-temp_stress_30.png|600px]]
Testing 1Gbps Ethernet on the Raspberry Pi CM5
Use iPerf Tool to Test Network Speed/Bandwidth, Getting max 961Mbps
[[File:X1501v1.0-1GbE.png|600px]]
Performance test for write speeds on an OpenMediaVault (OMV) shared folder
[[File:1GbE-SSD1-w.png|600px]]
Performance test for read speeds on an OpenMediaVault (OMV) shared folder
[[File:1GbE-SSD1-r.png|600px]]
Testing disk drive read speed with hdparm
[[File:X1507_hdparm.png|600px]]
==Packing List==
* 2.54mm jumer cap x2
* Screw pack x1
==FAQ==
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
</div>
<div class="mw-collapsible-content">
A: Place When using an external antenna, you need to configure the answer heredevice accordingly.Please follow the official Raspberry Pi documentation for the configuration steps:https://www.raspberrypi.com/documentation/computers/compute-module.html#antenna[[File:Antenna-configuration.jpg|none|Antenna Configuration]]
</div>
</div>