3,252
edits
Changes
{{GD Template Impl}}
[[File:X1206-Overview-1.jpg|thumb|right|X1206 UPS Shield for RPi 5]]
[[File:X1206-IMG-7240-Interface-New.jpg|thumb|right|X1206 Raspberry Pi 5 UPS-Interface]]
[[File:X1206-IMG-9058.jpg|thumb|right|X1206 Raspberry Pi 5 UPS-Battery Requirement]]
[[File:X1206-IMG-6837-How-to-Power.jpg|thumb|right|How to Power X1206 Raspberry Pi 5 UPS]]
[[File:X1206-V1.1-Overview.jpg|thumb|right|X1206 Raspberry Pi 5 UPS]]
==Safety Instructions & Warnings==
* <span class="tb_red">You must read these safety instructions and warnings before charging your batteries.
'''<span class="tb_red">What is the difference between [[X1206]] and [[X1202]]:</span>'''
*X1206 uses a wide voltage power input (9V-18V);
<!--
*Solves the overheating problem of DC jack power supply
-->
*Uses a higher capacity '''21700''' lithium battery to provide longer power supply time;
* The power supply capacity through the DC jack is greatly increased from 5.5A of [[X1202]] to 10A
==Features==
{| class="wikitable"
|- |'''For use with''' || Raspberry Pi 5 Only|-|- '''Key FeaturesUPS Output''' || '''UPS Output'''
* Provides continuous operation for up to 10 hours (duration depends on battery type and applications)
* Supports a maximum current output of '''5.1V 6000mA''', suitable for most Raspberry Pi applications
* Convenient pogo pin connection for powering the Pi, eliminating the need for cabling and soldering
* Equipped with XH2.54 connectors and two USB sockets for 5V power output (Share 6000mA current output)
|-| '''Battery Charging'''||
* Supports fast battery charging with a upto 3000mA current
* Battery charging control can be managed via GPIO
* On-board LEDs indicate battery charging and discharging levels of 25%, 50%, 75%, and 100%
* Features a 4-cell 21700 battery holder, supporting up to 20,000mAh with four 21700 batteries
|-|'''Power Input'''||
* Integrated high-efficiency step-down DC-DC converter
* Wide operating input range of 9V to 18V, strongly recommen [[PSU60 | Geekworm 12V 5V Power supply]]
* The power supply with DC jack can get up to 10A input current, which can achieve 3A fast charging while powering the system. Of course, this also depends on the DC power adapter you use. A good quality power adapter is very important.
* Allows power input from various sources such as a car, solder panel, and more
* '''Common power input jack size of 5.5x2.1mm'''* '''No longer provides TYPECompatible with Raspberry Pi USB-C charging portPower Supply'''|-|'''Power Management'''||
* Seamless power switching between backup power and power adapter
* On-board push button performs the same actions as the '''RPi 5''''s power button
* Ultra-low standby power consumption to maximize battery life
* Advanced system power-path management to minimize frequent charging and discharging of batteries
|-|'''Misc'''||
* Connects to the Pi via convenient pogo pins, eliminating the need for additional cabling
* Designed to be attached on the bottom, allowing the use of favorite HATs alongside it
*1 x X1206 UPS Shield
*4 x CM2.5*4 screws
[[File:X1206-IMG-9057-packing-list.jpg|600px]]
==User Manual==
* Hardware X1206 Software: [https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1206 Software]* Low voltage warning solution for X120x Series UPS: [[File:IMG-7278-Low-Voltage.jpg | 700px]] * InstallationGuide Installation Video https://youtu.be/T7AZgkphaKI{{#ev:youtube|https: //youtu.be/T7AZgkphaKI}} ==Matching Case==X1206-C1 case is designed for the raspberry pi 5 & X1206 ups shield only, also with space reserved on the top for mounting the Raspberry Pi 5 PIP boards, such as the X1001, X1004, X1003, X1000 and M901.* How to make it workCase dimensions:112 x 91 x 64 mm / 4.41 x 3.58 x 2.52 inches <gallery>01-X1206-C1-IMG-9101.jpg|X1206-C102-X1202-C1-IMG-8199-layer.jpg|X1206-C1 Applicatioon03-X1206-C1-IMG-9103-interface-NEW.jpg|X1206-C1 Interface-Front04-X1206-C1-IMG-9103-interface.jpg|X1206-C1 Interface-Rear05-X1206-C1-IMG-9106-size.jpg|X1206-C1 Dimension06-X1206-C1-IMG-8202-Packing_List.jpg|X1206-C1 Accessories</gallery>
==FAQ==
<!--Add review function! -->
[[Category:Product Manual]]
[[Category:Raspberry pi]]