Changes

Jump to navigation Jump to search

X1005

5,060 bytes added, 19 September
{{GD Template Impl}}
[[File:X1005-V1.0-IMG-8492-Interface.jpg|thumb|right|X1005 V1.0 View]]
[[File:X1005-V1.0-IMG-8507-FFC-cable-installation.jpg|thumb|right|X1005 V1.0 FFC Cable Installation]]
[[File:X1005-V1.0-IMG-8510-SSD-Installation-2.jpg|thumb|right|X1005 V1.0 SSD Installation]]
[[File:X1005-V1.0-IMG-8500.jpg|thumb|right|X1005 V1.0 & Pi5]]
[[File:X1005-V1.0-IMG-8505.jpg|thumb|right|X1005 V1.0 & Pi5 & H505]]

==Overview==
X1005 NVMe dual SSD shiel is designed to provide a seamless and high-speed storage solution for your Raspberry Pi 5. Its sleek and compact design enables easy attachment of '''two M.2 SSDs''' with multiple lengths (including 2280, 2260, 2242, and 2230) to your Raspberry Pi 5. With its '''PCIe 2.0''' interface, you can experience data transfer rates of up to 5Gbps, allowing you to effortlessly transfer large amounts of data within seconds.

The X1005 is installed on the rear side of the Raspberry Pi 5, eliminating the need for a passthrough for the GPIO. This means you can use your favorite HATs while also utilizing the NVMe shield. Additionally, it seamlessly integrates with the Raspberry Pi official passive cooler without compromising heat dissipation. The inclusion of mounting holes and standoffs provides added protection for your solid-disk drives while effectively dissipating heat. The built-in LED light indicates the current reading or writing status, eliminating any guesswork.

The X1005 is an ideal storage solution for creating a home media center or building a network-attached storage (NAS) system. It allows you to store and stream your own videos, music, and digital photos within your home or even remotely across the world.

* X1005 also supports '''hailo-8 ai accelerator''' and can also support booting from another SSD. (Note: Hailo-8 ai and ssd share the bandwidth of PCIe 2.0. Due to the limitation of ASMedia ASM1182e PCIe switch, X1005 do not support PCIe 3.0.)
----
{{PCIe to NVME Sets}}

== Important Notes==
{{NVMe SSD Incompatibility List}}

==Features==
{| class="wikitable"
|-
| '''For use with''' ||
* Raspberry Pi 5B
|-
| '''Key Features''' ||
* Ideal PCIe storage solution for Raspberry Pi 5 - '''Dual M.2 NVMe SSD Shield'''
* Supports a total of 8TB storage capacity (4TB+4TB) with M.2 NVMe solid-state drives
* Accommodates two various M.2 NVMe SSD form factors, including 2280, 2260, 2242, and 2230
* Supports '''PCIe 2.0''' 5Gbps for speedy data transfer and super-fast boot
* Fully compatible with the Raspberry Pi official active cooler
* LED indicators in blue display power and drive status
* Features an integrated high-performance PCIe packet switch
* Equipped with two high-efficiency DC/DC step-down converters, delivering a maximum of 6A to power your SSDs
* Designed to be attached on '''bottom''', allows using your favorite HATs alongside it
* Powering via both pogo pins and FFC, ensuring sufficient power supply without any worries
|-
| '''Technical Specification''' ||

'''Power supply:''' <span class="tb_red">5Vdc +/-5%</span> power via pogo pins & FFC, converted to 3.3V max 6A to power the SSDs

'''Ports & Connectors:'''
* PCIe connector - 16-pin pitch0.5mm
* SSD connector - M.2 KEY-M 67P

'''PCIe cable length''' 37mm x2

'''PCB Size:''' 86.5mm x 60mm

|-
| '''Important Notes''' ||
* Compatible with M.2 NVMe SSDs
* Not compatible with M.2 SATA SSDs, M.2 PCIe AHCI SSDs, or other M.2 non-NVMe devices
* Older NVMe drives with less efficient flash media may not perform as well as newer drives
* New NVMe SSDs are not partitioned and will need to be both partitioned and formatted when first connected to the Raspberry Pi before they will be accessed in the Explorer.
* Since X1005 is using [https://www.asmedia.com.tw/product/213yQcasx8gNAzS4/b7FyQBCxz2URbzg0 ASMedia ASM1182e] PCIe switch, it can't support PCIe Gen 3 speed, so even though we forced to turn on PCIe Gen 3.0 setting in Raspberry Pi 5, it is limited by ASMedia ASM1182e PCIe switch. speed is still PCIe Gen 2.0 speed.
|}

==Matching Case==
Refer to [[P580|P580-V2]].

==Packing List==
* X1005 V1.0 NVMe shield x1
* PCIe FFC 37mm x 2 (1pc is for backup)
* M2.5*10mm Screw x 2
* M2.5*5mm Screw x 4
* M2.5*5mm Spacer x 4
* SSD Copper Pillar x 2 (to fix 2230 / 2242 / 2260 length SSD)
* M2*4 Screw x 2 (to fix SSD)
[[File:X1005-V1.0-IMG-8094-Packing-List.jpg|600px]]

==User Manual==
* X1005 Hardware: [https://suptronics.com/Raspberrypi/Storage/x1005-v1.0_hardware.html X1005 Hardware]
* Software tutorials: [[NVMe SSD boot with the Raspberry Pi 5]]
* [https://datasheets.raspberrypi.com/pcie/pcie-connector-standard.pdf Raspberry pi 5 pcie connector pin out]

==Hardware Installation==
Installation Video for Raspberry Pi 5+X1005+P580-V2+Cooler: https://youtu.be/GLGxn9JmN0g

{{#ev:youtube|https://youtu.be/GLGxn9JmN0g}}

[[File: X1005-P580-V2-Installation.jpg|700px]]

==FAQ==
{{X100x-FAQ}}

<!--Add review function! -->
<comments />

<!--Please choose the -->
<!--Remove other categories, just keep the appropriate categories -->

[[Category:Product Manual]]
[[Category:Raspberry pi]]

Navigation menu