5,636
edits
Changes
Jump to navigation
Jump to search
no edit summary
In fact, some PIPs such as [[X1001]] / [[X1002]] / [[X1003]] / [[X1000]] etc are just an extension of the Raspberry Pi 5 PCIe, and their own hardware functions are limited. If the '''OS configuration''' and '''PCle FFC cable faults''' can be ruled out, the normal operation of PCIe (recognizing and booting) depends more on the '''firmware''' and '''SSD compatibility'''. Since October 2023, the Raspberry Pi Foundation has been updating the bootloader version to solve similar problems. You can learn more from the link below.
[https://github.com/raspberrypi/rpi-eeprom/blob/master/firmware-2712/release-notes.md Raspberry Pi5 bootloader EEPROM release notes]
<span class="tb_red">After several major version updates, the bootloader has basically solved the firmware issue, so the remaining is the '''OS configuration''' and '''SSD compatibility''' issues.</span>
If you are using a very old SSD, if you are experiencing issues with it being recognised and not being able to boot, the first thing you should consider is replacing the NVME SSD.
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0; color:red;">
Q1: Can't boot/recognize from NVMe SSD?
</div>
<div class="mw-collapsible-content">
[[File:Supported-SSD-1.jpg|thumb|right|300px|click it to zoom out]]
A: Here are a few steps to help you troubleshoot some issues：
#'''Only''' Raspberry Pi OS ('''Bookworm''') supports PCIe, Raspberry Pi OS bullseye is NOT supported, refer to https://www.raspberrypi.com/software/operating-systems/
# Make sure that your OS configuration (<code>/boot/firmware/config.txt</code>) is completely correct: refer to the tutorial:[[NVMe SSD boot with the Raspberry Pi 5]] (will Continuously updating)
# <span class="tb_red">Update the bootloader firmware to the last verson, refer to [[How to update eeprom firmware]], this is very important!!!</span> Make sure your upgrade is successful by running command '''vcgencmd bootloader_version'''
# Add '''''PCIE_PROBE=1''''' to the eeprom, (Run '''sudo rpi-eeprom-config --edit''' command, then add this line, then press CTRL+O to write change to file, press CTRL+X to exit, then '''reboot''')
# Make sure the SSD type you use is correct, only support <span class="tb_red">M.2 NVME (Sata) Key-M SSD '''</span>NOT support''' M.2 NGFF Key-B SSD. Refer to the right diagram:
# Make sure the FPC cable is '''firmly and fully inserted''' into the PI 5, this is '''very important'''. For [[X1003]] shield, make sure the FPC cable '''direction''' is correct also.
# For some small brand SSD, consider forcing open '''PCIe Gen3''' to test (add <code>dtparam=pciex1_gen=3</code> line in '''config.txt''' then '''reboot'''), because some small brand SSDs are '''NOT backward compatible with PCIe Gen 2''' for cost reasons.
# <span class="tb_red_bold">For [[X1003]] shield, make sure the FPC cable '''direction''' is correct also. If an error still occurs, replace the FFC cable to test or purchase other PFC from here<ref><br/>Amazon US: https://www.amazon.com/dp/B0CXCTPQ2N
<br/>Amazon DE: https://www.amazon.de/dp/B0CX4T993J
<br/>Amazon UK: https://www.amazon.co.uk/dp/B0CX4T993J
<br/>Amazon JP: https://www.amazon.co.jp/dp/B0CYGKN7G1
</ref>to troubleshoot the issue.<span>
# Read [https://geekworm.com/community/forum/topic/120764/geekworm-x1001-for-raspberry-pi-5 this post] to get some help;
# Although you can also boot from a SD card, Pi OS is required for the NVMe SSD to boot, DON'T forget Flash OS into NVMe SSD.
# If you're flashing a fresh Pi OS into NVME SSD , DON'T forget to '''ENABLE PCIe''' to NVME SSD.
# Run the '''lspci''' and '''lsblk''' command to check the NVMe SSD is recognized. (NOTE: Make sure your '''NVMe SSD is plugged into the PCIe PIP''', not just connecting PCIe PIP to the Pi5, otherwise the lspci will not be able to display any PCIe device). For [[X1004]], [[X1005]], [[Q200]] and [[X1011]], , you can only see several '''ASMedia Technology PCIe''' devices when running '''lspci''', but not the NVME SSD information. You need to use the '''lsblk''' command to check whether NVME can be recognized.
<!--# If your SSD is old and has a '''DOS partition''', delete the DOS partition and repartition the SSD (feedback from buyer)-->
# Start thinking about SSD compatibility issues and try to switch to other brands of NVME SSDs. Some customers have reported that they have successfully solved their problems by replacing their SSDs.
# Contact us at email: support@geekworm.com, and attached your product model, OS version (run '''uname -a''' to get), bootloader version (run '''vcgencmd bootloader_version''' to get) and order number
:*'''How to get FPC Wires:'''
<references />
:*<span class="tb_red">PS: The shortest length of the FPC cable here is '''30mm''', but the length of the FPC cable used by X1003 is only '''22mm'''. For X1003, this may not be perfect, but you can use these FPC cables to troubleshoot the issue. DON'T buy it if you mind.</span>
:*If the issue is confirmed to be a FFC cable, we will reimburse you the cost of purchasing the FFC cable.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q2: Don't recognize / boot from NVME SSD?
</div>
<div class="mw-collapsible-content">
A: If you have '''enabled pcie''' and find that you still cannot boot from NVME SSD, please perform the following actions
1. Follow the picture below to check the version of [[X1001]] or [[X1000]]
[[File:X1001-V1.1-IMG-6871-old-new.jpg|600px]]
2. If it is an '''Old Version''', refer to [[How to update eeprom firmware]] to update the firmware with '''pieeprom-2023-10-30.bin file'''.
3. If it is an '''New Version''', refer to [[How to update eeprom firmware]] to update the firmware to '''lasted version'''.
4. '''If you still have not solved the problem, please refer to the next FAQ:Q1'''
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q3: How to fix the 2230/2242/2260 SSD on X1001 or other PIP?
</div>
<div class="mw-collapsible-content">
A: The X1001 and other pips does not reserve the nut column to fix the 2230/2242/2260 SSD. Based on our test, you can secure the 2230/2242/2260 SSD using an M2*6mm screw and 2pcs M2 nuts. Place one M2 nut under the SSD, then use the M2*6mm screw and the other M2 nut to fasten the SSD.
<SPAN class="tb_red_bold">PS: As of April 2024, we have added customized copper pillar in only '''X1001''' packing list to solve this issue, please refer to [[X1001#Packing_Lis | the packing list of X1001]].</SPAN>
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q4. X1002 can't boot when install into the P580 case?
</div>
<div class="mw-collapsible-content">
A: Please check if the FPC cable touch the metal case make shorting when install X1002 into the metal case, you can stick the electrical tape on the case to prevent the ribbon FPC cable from contacting the case to test.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q5: Which NVMe drives work with a Raspberry Pi 5?
</div>
<div class="mw-collapsible-content">
A: You can refer to the video: https://youtu.be/3mUgVTBmKio.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q6: Can they support gen3 PCIe speeds or only gen2?
</div>
<div class="mw-collapsible-content">
A:
* All PIPs (such X1001, X1002, X1003 etc) are just an extension of the Raspberry Pi 5 PCIe interface. Apart from whether the chip on the PIP board supports PCIe 3.0 or not, the more main focus is on the Raspberry Pi 5.
* X1004, X1011, X1005 PIP boards do not support PCIe Gen 3 speed.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q7: Why can the SSD be recognized but not bootable?
</div>
<div class="mw-collapsible-content">
A:Please consider the following advice:
* The method of flashing OS to NVME SSD may be problematic.
It is recommended that you boot from the SD card first and then use the '''SD Card Copier''' tool to flash the OS to the NVME SSD. Refer to [[NVMe_SSD_boot_with_the_Raspberry_Pi_5#Flash_OS_onto_NVME_SSD]]
* The SSD used may be incompatible. Please replace it with other brand SSD.
</div>
</div>
[https://github.com/raspberrypi/rpi-eeprom/blob/master/firmware-2712/release-notes.md Raspberry Pi5 bootloader EEPROM release notes]
<span class="tb_red">After several major version updates, the bootloader has basically solved the firmware issue, so the remaining is the '''OS configuration''' and '''SSD compatibility''' issues.</span>
If you are using a very old SSD, if you are experiencing issues with it being recognised and not being able to boot, the first thing you should consider is replacing the NVME SSD.
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0; color:red;">
Q1: Can't boot/recognize from NVMe SSD?
</div>
<div class="mw-collapsible-content">
[[File:Supported-SSD-1.jpg|thumb|right|300px|click it to zoom out]]
A: Here are a few steps to help you troubleshoot some issues：
#'''Only''' Raspberry Pi OS ('''Bookworm''') supports PCIe, Raspberry Pi OS bullseye is NOT supported, refer to https://www.raspberrypi.com/software/operating-systems/
# Make sure that your OS configuration (<code>/boot/firmware/config.txt</code>) is completely correct: refer to the tutorial:[[NVMe SSD boot with the Raspberry Pi 5]] (will Continuously updating)
# <span class="tb_red">Update the bootloader firmware to the last verson, refer to [[How to update eeprom firmware]], this is very important!!!</span> Make sure your upgrade is successful by running command '''vcgencmd bootloader_version'''
# Add '''''PCIE_PROBE=1''''' to the eeprom, (Run '''sudo rpi-eeprom-config --edit''' command, then add this line, then press CTRL+O to write change to file, press CTRL+X to exit, then '''reboot''')
# Make sure the SSD type you use is correct, only support <span class="tb_red">M.2 NVME (Sata) Key-M SSD '''</span>NOT support''' M.2 NGFF Key-B SSD. Refer to the right diagram:
# Make sure the FPC cable is '''firmly and fully inserted''' into the PI 5, this is '''very important'''. For [[X1003]] shield, make sure the FPC cable '''direction''' is correct also.
# For some small brand SSD, consider forcing open '''PCIe Gen3''' to test (add <code>dtparam=pciex1_gen=3</code> line in '''config.txt''' then '''reboot'''), because some small brand SSDs are '''NOT backward compatible with PCIe Gen 2''' for cost reasons.
# <span class="tb_red_bold">For [[X1003]] shield, make sure the FPC cable '''direction''' is correct also. If an error still occurs, replace the FFC cable to test or purchase other PFC from here<ref><br/>Amazon US: https://www.amazon.com/dp/B0CXCTPQ2N
<br/>Amazon DE: https://www.amazon.de/dp/B0CX4T993J
<br/>Amazon UK: https://www.amazon.co.uk/dp/B0CX4T993J
<br/>Amazon JP: https://www.amazon.co.jp/dp/B0CYGKN7G1
</ref>to troubleshoot the issue.<span>
# Read [https://geekworm.com/community/forum/topic/120764/geekworm-x1001-for-raspberry-pi-5 this post] to get some help;
# Although you can also boot from a SD card, Pi OS is required for the NVMe SSD to boot, DON'T forget Flash OS into NVMe SSD.
# If you're flashing a fresh Pi OS into NVME SSD , DON'T forget to '''ENABLE PCIe''' to NVME SSD.
# Run the '''lspci''' and '''lsblk''' command to check the NVMe SSD is recognized. (NOTE: Make sure your '''NVMe SSD is plugged into the PCIe PIP''', not just connecting PCIe PIP to the Pi5, otherwise the lspci will not be able to display any PCIe device). For [[X1004]], [[X1005]], [[Q200]] and [[X1011]], , you can only see several '''ASMedia Technology PCIe''' devices when running '''lspci''', but not the NVME SSD information. You need to use the '''lsblk''' command to check whether NVME can be recognized.
<!--# If your SSD is old and has a '''DOS partition''', delete the DOS partition and repartition the SSD (feedback from buyer)-->
# Start thinking about SSD compatibility issues and try to switch to other brands of NVME SSDs. Some customers have reported that they have successfully solved their problems by replacing their SSDs.
# Contact us at email: support@geekworm.com, and attached your product model, OS version (run '''uname -a''' to get), bootloader version (run '''vcgencmd bootloader_version''' to get) and order number
:*'''How to get FPC Wires:'''
<references />
:*<span class="tb_red">PS: The shortest length of the FPC cable here is '''30mm''', but the length of the FPC cable used by X1003 is only '''22mm'''. For X1003, this may not be perfect, but you can use these FPC cables to troubleshoot the issue. DON'T buy it if you mind.</span>
:*If the issue is confirmed to be a FFC cable, we will reimburse you the cost of purchasing the FFC cable.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q2: Don't recognize / boot from NVME SSD?
</div>
<div class="mw-collapsible-content">
A: If you have '''enabled pcie''' and find that you still cannot boot from NVME SSD, please perform the following actions
1. Follow the picture below to check the version of [[X1001]] or [[X1000]]
[[File:X1001-V1.1-IMG-6871-old-new.jpg|600px]]
2. If it is an '''Old Version''', refer to [[How to update eeprom firmware]] to update the firmware with '''pieeprom-2023-10-30.bin file'''.
3. If it is an '''New Version''', refer to [[How to update eeprom firmware]] to update the firmware to '''lasted version'''.
4. '''If you still have not solved the problem, please refer to the next FAQ:Q1'''
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q3: How to fix the 2230/2242/2260 SSD on X1001 or other PIP?
</div>
<div class="mw-collapsible-content">
A: The X1001 and other pips does not reserve the nut column to fix the 2230/2242/2260 SSD. Based on our test, you can secure the 2230/2242/2260 SSD using an M2*6mm screw and 2pcs M2 nuts. Place one M2 nut under the SSD, then use the M2*6mm screw and the other M2 nut to fasten the SSD.
<SPAN class="tb_red_bold">PS: As of April 2024, we have added customized copper pillar in only '''X1001''' packing list to solve this issue, please refer to [[X1001#Packing_Lis | the packing list of X1001]].</SPAN>
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q4. X1002 can't boot when install into the P580 case?
</div>
<div class="mw-collapsible-content">
A: Please check if the FPC cable touch the metal case make shorting when install X1002 into the metal case, you can stick the electrical tape on the case to prevent the ribbon FPC cable from contacting the case to test.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q5: Which NVMe drives work with a Raspberry Pi 5?
</div>
<div class="mw-collapsible-content">
A: You can refer to the video: https://youtu.be/3mUgVTBmKio.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q6: Can they support gen3 PCIe speeds or only gen2?
</div>
<div class="mw-collapsible-content">
A:
* All PIPs (such X1001, X1002, X1003 etc) are just an extension of the Raspberry Pi 5 PCIe interface. Apart from whether the chip on the PIP board supports PCIe 3.0 or not, the more main focus is on the Raspberry Pi 5.
* X1004, X1011, X1005 PIP boards do not support PCIe Gen 3 speed.
</div>
</div>
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q7: Why can the SSD be recognized but not bootable?
</div>
<div class="mw-collapsible-content">
A:Please consider the following advice:
* The method of flashing OS to NVME SSD may be problematic.
It is recommended that you boot from the SD card first and then use the '''SD Card Copier''' tool to flash the OS to the NVME SSD. Refer to [[NVMe_SSD_boot_with_the_Raspberry_Pi_5#Flash_OS_onto_NVME_SSD]]
* The SSD used may be incompatible. Please replace it with other brand SSD.
</div>
</div>