2,301
edits
Changes
no edit summary
{{GD Template Impl}}
[[File:X1012v1.2X1012-1200p1.jpg|thumb|right| X1012 V1.2-Front View]][[File:X1012v1.2IMG-8035-1200p2interface.jpg|thumb|right| X1012 V1.2-Front ViewInterface]][[File:X1012v1.2-1200p3PCB-Layout.jpgpng|thumb|right| X1012 V1.2-Rear ViewPCB Layout]]
[[File:X1012v1.2-1200p4.jpg|thumb|right| X1012 V1.2 & NVMe SSD]]
[[File:X1012v1.2-1200p5.jpg|thumb|right| X1012 V1.2 & NVMe SSD]]
* PoE Supported – Power over Ethernet for simplified installation
* Fully isolated switched-mode power supply
* Compatible with <span class="tb_red">802.3af/at </span> Specifications
* Supports 48V Auxiliary Adapter Supply
* Input voltage: 37–57V DC, Class 4 device
'''NVMe'''
* Accommodates various M.2 NVMe SSD form factors, including 2280, 2260, 2242, and 2230
* Supports operating system booting from your SSD
* Does not compromise cooling performance and is fully compatible with the official active cooler
* Features a blue LED indicator that displays power and drive status
* Equipped with an integrated high-efficiency DC/DC step-down converter, providing up to 6A 5A of power for your SSD
|-
| ''' Technical Specification''' ||
<span class="tb_red">'''Power supply:''' 35-57VDC powering over Ethernet </span> or <span class="tb_red">40-57Vdc via Auxiliary power jack</span>
'''Ports & Connectors:'''
|}
==Matching Case==
X1012 is compatible with [[P579 | P579-V2]] case, though <span class="tb_red">the case doesn't reserved port for the DC power of X1012</span>. Because X1012 support POE, and DC jack is just an auxiliary power jack that non-essential.
[[File:X1012-Case.jpg|600px]]
==User Manual==
===Hardware Installation===
[[File:X1012-P579-V2-Installation.jpg|600px]]
===Configuration Tutorial===
# Enable PCIe to make nvme ssd work, please refer to [[NVMe SSD boot with the Raspberry Pi 5]]
# Tell the Pi that the X1012 POE is capable of 5A, so the USB current will get the full 1.6A
:: sudo rpi-eeprom-config -e
::Add <code>PSU_MAX_CURRENT=5000</code> at the end of the file that reads like this:
::[[File:X1012-setting.png|700px]]
::Press '''Ctrl-O''', then enter, to write the change to the file.
::Press '''Ctrl-X''' to exit nano (the editor).
::Reboot your Raspberry Pi 5 to make the change take effect.
===Introduction to Implementing Auxiliary Power on POE===
* Introduction to Implementing Auxiliary Power on POE: [[File:AN3472-Implementing-Aux-Power-in-PoE.pdf]]
==Packing List==
* 1 x X1012 V1.2 NVMe with POE shield
* 2 x PCIe FFC (30mm length, Provides a backup)
* 10 x M2.5*5mm screws
* 4 x M2.5*19mm F/F Spacer
* 1 x M2.5* 7mm F/F Spacer (And two M2.5*5 screws to fix the 2230/2242/2260 SSDs)
* 1 x CM2x3mm screw (sliver color, to fix 2280 SSD only)
[[File: X1012-Packing-List-1.jpg | 600px]]
==Test & Reviews==
'''Test Conditions'''
[[File: Testing-disk-drive-read-speed-with-hdparm-pcie3.png | 700px]]
==FAQ==