Open main menu
Geekworm Wiki

Changes

NASPi CM4-2.5

3,412 bytes added, 17 April
[[File:X510-IMG-5797.jpg|thumb|Internal view]]
[[File:X510-IMG-5795.jpg|thumb|Supports 2.5 inch SSD/HDD]]
[[File:X510-6Pin-Headers.jpg|thumb|X510]]
==User Manual==
===How to installing the Operating System (CM4 without eMMC)?Installation Video===Refer to [For NASPi CM4-2.5 and NASPi CM4-M2: https://wwwyoutu.raspberrypi.combe/documentationlXBK5-GFQ48{{#ev:youtube|https:/computers/getting-startedyoutu.html#installingbe/lXBK5-the-operating-system Official installation tutorial]===How to flash OS onto the SSD（Optional）===Load OS into ssd and you can get extremely fast running speed, you need to refer to the above steps to flash the OS into the Micro SD card firstly, then insrt the Micro sd card, turn on the device, and then click '''Applications''' =>'''Accessories''' =>'''SD Card Copier''', run the '''SD Card Copier''' program, and copy the OS to the NVME ssd as shown in the figure below.GFQ48}}
Please follow the steps below ===Flash OS Image===Due to CM4 has a version with eMMC, micro SD card is optional. If you are using the CM4 with eMMC, you don't need to buy a extra Micro SD card. You flash the OS image into different media according to your own situation. ====1. Flash OS into the micro SD card====:A minimum 16 Gb class 10 memory card is recommended. :Please refer to [https://www.raspberrypi.com/documentation/computers/getting-started.html#installing-the-operating-system Official installation tutorial] ====2. Flash OS into the eMMC of CM4(Optional)====:You can falsh OS into the eMMC if you use the CM4 '''with eMMC''', refer to the following step. :1. Short OTG Pin, refer to the picture below. :[[File:SdX515-IMG-copoer5890-scrot1.pngjpg|500px]] :2. Connect a computer that will be used to load the eMMC to the USB C port on the CM4-M2 board. The computer will provide both power and data to the CM4. (Type-A to Type-C OTG cable need to be purchased seperately) :3. Then rerfer to [https://www.jeffgeerling.com/blog/2020/how-flash-raspberry-pi-os-compute-module-4-emmc-usbboot this tutorial]to flash raspberry pi OS :4. Remove the jumper of OTG after flashing is complete, then restart your device; :'''PS：If you use CM4 with eMMC, then SD card cannot be used.''' ===3. Preconfigure Device for CM4===Now we think you have successfully flashed the OS to the storage media (mciro sd card or eMMC of CM4). If you attempt to boot now you will not have working USB ports, ssh, or any wireless configuration, so do not remove your SD card, proceed as follows. We can preconfigure your CM4 device by plugging mico sd via sd reader into a windows computer / Pi. You should see the “boot” volume where we can preconfigure our CM4 to be working right from the start. ====3.1 Enable USB Ports====:When mounted in the IO board the USB ports will not function without making a change to config.txt and adding an overlay. :Add the following line to config.txt: dtoverlay=dwc2,dr_mode=host:After adding this line the two USB ports (as well as the “External USB” header) will function the next time the CM4 boots. ====3.2 Enable SSH====:It's very useful to have SSH enabled when working with the Compute Module 4. It is enabled simply by creating an empty file named:
Click '''Start''' to run. Then shut down, unplug the SD card, and restart the device. touch ssh
===How to flash OS onto :in the eMMC root folder of CM4? the “boot” volume (CM4 with eMMC)?===1the top-most folder of the drive where start4x. Short nBOOT Pinelf, refer to the picture belowfixup.dat and those files are located)
[[File:X510-IMG-5886-1.jpg|500px]]Now when the Pi starts up SSH will automatically be enabled!
2. Connect Type:PS: This step is optional, you can also enable ssh through the <code>raspi-C OTG with a Type-A to Type-C cable to your computerconfig</code> program after the device boot
====3. Power 3 Preconfigure WiFi / Wireless (Optional)====:You can also preconfigure the device via PWR TypeCompute Module 4 (and any Pi) by creating wpa-C supplicant.conf at the base of the “boot” volume like we did with “ssh” file. In fact, you can setup your 5V Power adaperwifi after you boot up.
4:Create a new file named wpa-supplicant. Then rerfer to [httpsconf that contains the following:<pre>ctrl_interface=DIR=/var/www.jeffgeerling.com/blog/2020run/how-flash-raspberry-pi-os-compute-module-4-emmc-usbboot this tutorial] to flash raspberry pi OSwpa_supplicant GROUP=netdevcountry=USupdate_config=1
5. Remove network={ ssid="YourNetwork" psk="YourPassword"}</pre>When this file is created in the jumper base of nBOOT pin after flashing is complete, then restart the “boot” volume it will automatically be applied to the Pi upon the next startup. Make sure to adjust your country=US line to your own country as this can impact what channels and functionality are available from your device;WiFi card!
'''PS：If Then you use CM4 with eMMC, then SD can insert your micro sd card cannot be usedinto the device & power on it.'''
===Power management & safe shutdown 4. Installing script installation===Refer After the device is reboot, install the following script to get safe and software shutdown function: refer to [[XScript]]
===How to enable 5. Enable OLED display===
Refer to [[How to enable OLED display]]
 
===6. Flash OS into the NVME SSD（Optional）===
Load OS into ssd and you can get extremely fast running speed, you need to refer to the above steps to flash the OS into the Micro SD card firstly, then insrt the Micro sd card, turn on the device, and then click '''Applications''' =>'''Accessories''' =>'''SD Card Copier''', run the '''SD Card Copier''' program, and copy the OS to the ssd as shown in the figure below.
 
[[File:Sd-copoer-scrot.png]]
 
Click '''Start''' to run. Then shut down, unplug the SD card, and restart the device.
 
==FAQ==
<div class="toccolours mw-collapsible mw-collapsed">
<div style="font-weight:bold;line-height:1.0;">
Q: How to enable the POE option?
</div>
<div class="mw-collapsible-content">
A. The POE header on X515/X510 is reserved to be compatible with the official POE+ HAT. But we don't know if the case will be compatible with the installation of official POE+ HAT.
</div>
</div>
 
==Video==
Thanks for the video from leepspvideo!
https://youtu.be/tgSNGbbFk1c
{{#ev:youtube|https://youtu.be/tgSNGbbFk1c}}
<!--Add review function! -->
Retrieved from "https://wiki.geekworm.com/Special:MobileDiff/16648...19934"