Admin: Replace with

2026-05-27T02:13:47Z

Replace <comments/> with <comment-streams />

← Older revision		Revision as of 10:13, 27 May 2026
Line 54:		Line 54:
	Return to [[X630]]		Return to [[X630]]

	<comment-streams />		<comment-streams id="main" />
	[[Category:Raspberry pi]]		[[Category:Raspberry pi]]
	[[Category:Knowledge]]		[[Category:Knowledge]]

Admin: Replace with

2026-05-26T12:07:55Z

Replace <comments/> with <comment-streams />

← Older revision		Revision as of 20:07, 26 May 2026
Line 54:		Line 54:
	Return to [[X630]]		Return to [[X630]]

	<~~comments~~/>		<comment-streams />
	[[Category:Raspberry pi]]		[[Category:Raspberry pi]]
	[[Category:Knowledge]]		[[Category:Knowledge]]

Harry at 11:28, 24 April 2026

2026-04-24T11:28:35Z

← Older revision		Revision as of 19:28, 24 April 2026
Line 55:		Line 55:

	<comments/>		<comments/>
			[[Category:Raspberry pi]]
			[[Category:Knowledge]]

Cindy: /* X630 Reset Setting */

2023-02-14T03:33:10Z

X630 Reset Setting

New page

==Interface==
[[File:X630-diagram.png|800px]]

==10-pin functional connector==
{| class="wikitable"
! Pin No. !! Pin Name !! Function !! Note
|-
| 1 || 3V3 || 3.3V output || 3.3V
|-
| 2 || HDET || HDMI input detect (high level ) || 3.3V
|-
| 3 || IR || Infrared signal || 3.3V
|-
| 4 || INT || Interrupt Output signal – active high (Level) || 3.3V
|-
| 5 || RESET || System reset input, active low || 3.3V
|-
| 6 || A_SCK || I2S/TDM Bit Clock signal (BCK) || 3.3V
|-
| 7 || A_WFS || I2S Word Clock or TDM Frame Sync signal (LRCK) || 3.3V
|-
| 8 || A_OSCK || Audio Oversampling Clock (MCLK) || 3.3V
|-
| 9 || A_SD || I2S/TDM data signal (Data) || 3.3V
|-
| 10 || GND || Ground || 0V
|}

==X630 Reset Setting==
'''Note: Software reset only exists in V1.3 version, this function is no longer reserved in V1.5'''
[[File:X630-V1.5-VS-X630-V1.3.jpg|700px|none|X630 V1.5 vs X630 V1.3]]

[[File:Dip-switches.jpg|none|dip switch]]
{| class="wikitable"
! SELECTION !! SWITCH SETTINGS !!
|-
| Hardware reset || HW = 1 || SW = 0
|-
| Software reset || HW = 0 || SW = 1
|}

[[File:X630-Reset-01.jpg|none|800px|X630 dip switch setting]]

Explain：
* Hardware reset: After starting RASPISTILL or RASPIVID <span style="color:red;">once</span> then you will need to reboot Raspberry Pi to restart it again (Please use when operating system cannot control the X630 module via GPIO509)
* Software reset: Starting RASPISTILL or RASPIVID <span style="color:red;">multiple times</span> and don't need to reboot Raspberry Pi
* Default setting is 'Hardware reset';
* Please remove the yellow protective film before change dip switch.

== Mechanical Drawing==
[[File:X630-mechanical-drawing.png|x630 mechanical drawing]]

Return to [[X630]]

<comments/>

X630-Hardware - Revision history

Admin: Replace with

Admin: Replace with

Harry at 11:28, 24 April 2026

Cindy: /* X630 Reset Setting */