Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 17:57, 25 June 2025 Lisa talk contribs posted a new comment on X1001 (Hi, Sorry, we are not sure, you can refer to the official documentation.)
  • 09:01, 25 June 2025 173.54.57.150 talk posted a new comment on X1201 (Attempt to reseat the ups. Make sure the pogo pins are aligned correctly with each pin. Can you tell me if when you tunr it on, the LED thats labled "PI5" is on. that shows if the pi is detected. It can be tricky to know if the pins are aligned correctly, make sure theres a good connection. If it doesnt sense a pi connected to it, it will turn off after a few seconds as stated on the wiki.)
  • 07:57, 25 June 2025 68.197.206.6 talk posted a new comment on X1201 (Hi, I have the X1201 connected to my Raspberry Pi 5. When I connect to USB-C, the Pi powers up. When I am not connected to USB-C, when I press the power button on the X1201, the LEDs on the X1201 show the batteries are fully charged and that the Pi is connected. The green Pi LED lights briefly, and then the Pi goes into standby mode with a red LED. I have not changed anything in the Pi setup - I'm using a stock install of the latest Pi OS. What should I do?)
  • 06:55, 25 June 2025 173.54.57.150 talk posted a new comment on X1201 (Sorry lol, last question, how do I get the 5v in to work. Ive soldered a 2 pin usb C connector for power, but im not getting any sign. how is it used? please give an example. Thanks!)
  • 03:09, 25 June 2025 92.212.9.220 talk posted a new comment on X1001 (I have been running a WD SN770M for about 3-4 days on a somewhat idle Nextcloud install with it not crashing since I adjusted the bootloader settings with "dtparam=pciex1_gen=3,aspm=off". Is setting this alright or discouraged? If the latter, why?)
  • 18:14, 24 June 2025 Lisa talk contribs posted a new comment on X1009 (Hi, yes, you can power the RPi5 via Type C. because X1009 needs the V3.0V control of the RPi5，can not disconnect it all. You need to unplug the pins of PIN2 and PIN4 of expansion header (GPIO bridge connector) .)
  • 18:14, 24 June 2025 Lisa talk contribs deleted comment #5868 on X1009
  • 18:14, 24 June 2025 Lisa talk contribs posted a new comment on X1009 (Hi, yes, you can power the RPi5 via Type C. You need to unplug the pins of PIN2 and PIN4 of expansion header (GPIO bridge connector) . because X1009 needs the V3.0V control of the RPi5，can not disconnect it all.)
  • 17:22, 24 June 2025 Lisa talk contribs posted a new comment on X1008 (Hi,X1008 does not support the auto power-on.)
  • 14:31, 24 June 2025 173.70.167.178 talk posted a new comment on X1009 (> Hello, does not support power X1009 via Type C of RPi5. Thanks for your answer, Lisa! So I need to disconnect GPIO bridge connector if I want to power PI and X1009 separately? As documentation says: Don't power the X1009 via DC powe jack and the Raspberry Pi5 via USB-C at the same time. Just power the X1009, and then the X1009 will power the Pi 5 via the GPIO.)
  • 23:12, 23 June 2025 195.224.89.36 talk posted a new comment on X1008 (Hi, the board doesn't power on by itself after connecting the supply, it requires pressing the button. Can it be made to power automatically? This would be a lot better in case of power outage when there is no one home.)
  • 15:09, 23 June 2025 Lisa talk contribs posted a new comment on X1009 (Hello, does not support power X1009 via Type C of RPi5.)
  • 14:38, 23 June 2025 Lisa talk contribs posted a new comment on X1201 (Hi,The external power switch function is the same as the onboard switch.)
  • 05:13, 21 June 2025 173.70.167.178 talk posted a new comment on X1009 (Is it possible to power the Raspberry Pi 5 via a USB Type-C cable, while powering HDDs directly from an independent 12V power supply? In that case, will the Raspberry Pi 5 still be able to power the X1009 over GPIO — essentially in reverse? The DC 12V 5.5x2.1mm power input would not be used in this setup. If that is not possible, then I will need to use two 12V power supplies: - one 12V power supply for the X1009 (and Raspberry Pi 5) - another 12V power supply for the HDDs. The reason I'm...)
  • 10:08, 20 June 2025 173.54.57.150 talk posted a new comment on X1201 (Does the external power switch act as a full power switch? In context, if its unplugged, running off the 18650 batteries, will turning it on turn on the UPS also? and even the pi 5? Im asking because the PiSugar 2 Plus button acts as a soft power switch, which means making something like a cyberdeck would require 2 power buttons?)
  • 14:02, 19 June 2025 Lisa talk contribs posted a new comment on X1201 (Hello, You can write your own script to do this.)
  • 12:13, 19 June 2025 Lisa talk contribs posted a new comment on X1500 (Hello, the same as Raspberry Pi 5.)
  • 12:13, 19 June 2025 Lisa talk contribs posted a new comment on X1501 (Hello, the same as Raspberry Pi 5.)
  • 19:40, 18 June 2025 185.220.101.43 talk posted a new comment on X1500 (How to boot from NVME)
  • 02:43, 18 June 2025 162.210.4.245 talk posted a new comment on X1501 (What is the Operating temperature rating?)
  • 03:53, 16 June 2025 173.54.57.150 talk posted a new comment on X1201 (Is there a way to display battery status like percent on screen with pi os?)
  • 18:38, 13 June 2025 27.143.28.50 talk posted a new comment on CSI Manual on Pi 5 (I am trying to capture HDMI video from a TC358743 (C790 board) connected to a Raspberry Pi 5 running Linux kernel 6.12.25. The HDMI source is 1920×1080 @ 60Hz. EDID writing and media-ctl link configuration were completed as described in the documentation. Multiple /dev/video* nodes are present, including /dev/video0 and /dev/video4. I can set formats (e.g., RG16, BYR2) using v4l2-ctl on /dev/video0, but attempting to stream results in: VIDIOC_STREAMON: Invalid argument Even OpenCV and ffpl...) Tags: Mobile web edit, Mobile edit
  • 18:36, 13 June 2025 27.143.28.50 talk posted a new comment on C790 (I am trying to capture HDMI video from a TC358743 (C790 board) connected to a Raspberry Pi 5 running Linux kernel 6.12.25. The HDMI source is 1920×1080 @ 60Hz. EDID writing and media-ctl link configuration were completed as described in the documentation. Multiple /dev/video* nodes are present, including /dev/video0 and /dev/video4. I can set formats (e.g., RG16, BYR2) using v4l2-ctl on /dev/video0, but attempting to stream results in: VIDIOC_STREAMON: Invalid argument Even OpenCV and ffpl...) Tags: Mobile web edit, Mobile edit
  • 10:00, 13 June 2025 Lisa talk contribs posted a new comment on X1200 (Hi,please refer to the FAQ⬆ ---[Q. Documentation about the I2C registers：])
  • 09:28, 13 June 2025 Lisa talk contribs posted a new comment on KVM-A8 (The HDMI signal has been transferred to KVM-A8.Display acquisition is not supported.)
  • 02:29, 13 June 2025 115.99.105.203 talk posted a new comment on KVM-A8 (Please answer this question , that motherboard hdmi goes to kvm hdmi , so how we get display from the monitor ?) Tags: Mobile web edit, Mobile edit
  • 19:18, 12 June 2025 185.12.128.197 talk posted a new comment on X1200 (Hi. Is there a documentaton about the I2C registers? Or, do you have the specific IC we are communication with?)
  • 17:10, 11 June 2025 Lisa talk contribs posted a new comment on X1200 Hardware (Hi,I'm sorry I don't quite understand what you mean. Could you please explain it in more detail?)
  • 17:09, 11 June 2025 Lisa talk contribs posted a new comment on X1206 (X1206没有3.3V输出。请从RPi5主板的GPIO取。)
  • 17:08, 11 June 2025 Lisa talk contribs deleted comment #5846 on X1206
  • 16:23, 11 June 2025 Lisa talk contribs posted a new comment on X1206 (抱歉不太明白你的意思。你已经购买了X1206扩展版了吗？能具体说明一下您的问题吗？)
  • 10:56, 11 June 2025 223.104.68.128 talk posted a new comment on X1206 (这个3.3V从哪里取更好呢？) Tags: Mobile web edit, Mobile edit
  • 19:09, 9 June 2025 Lisa talk contribs posted a new comment on X1001 (Hello, Please try to check if the FFC cable connection is loose, or try another FFC cable.)
  • 07:09, 8 June 2025 85.206.119.247 talk posted a new comment on X1002 (can someone please share the height of resulting PI + X1002 sandwich, thanks)
  • 12:17, 7 June 2025 172.101.197.68 talk posted a new comment on X1200 Hardware (Hi, I can't get my Battery plugin for the taskbar in Pi5 to show. I have the x1200. Please advise.) Tags: Mobile web edit, Mobile edit
  • 11:01, 7 June 2025 120.148.188.50 talk posted a new comment on X1300 Software (Poorly explained above. "/dev/v4l-subdev2" needs to be changed to the CSI connected device found in the previous step, so in my case to "/dev/video0" The "PPS:Pay attention to the directory of your edid file" may be referring to where the EDID will be loaded to, rather then where the file is loaded from.)
  • 21:08, 5 June 2025 223.185.55.105 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (how to rotate the display?)
  • 21:14, 4 June 2025 94.31.108.40 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (Geekworm X1003 + Crucial P310 PCIe Gen4 NVMe 2TB: worked ok. In /boot/firmware/config.txt: dtparam=pciex1 dtparam=pciex1_gen=3 1. fio --randrepeat=1 --ioengine=libaio --direct=1 --gtod_reduce=1 --name=test --filename=fio-test.data --bs=4k --iodepth=64 --loops=1 --size=30G --readwrite=randrw --rwmixread=75 Output: test: (g=0): rw=randrw, bs=(R) 4096B-4096B, (W) 4096B-4096B, (T) 4096B-4096B, ioengine=libaio, iodepth=64 fio-3.33 Starting 1 process test: Laying out IO file (1 file / 30720MiB)...)
  • 03:21, 4 June 2025 93.202.155.183 talk posted a new comment on X1001 (I used this HAT on a Pi 5 with a crucial P3 Plus PCIe 4.0 M.2 2280 2TB for months. With no reason the SSD isn't booting anymore. When I use a SSD USB adapter the Pi boots fine from SSD again, so it seems that the HAT is broken after 6 months. What could be the cause? How to avoid?)
  • 18:29, 3 June 2025 Lisa talk contribs posted a new comment on X1001 (Hello, 1/What brand of SSD are you using? Please refer to here：NVMe SSD boot with the Raspberry Pi 5 to troubleshoot the following issues first. 2/If it is confirmed that the problem is caused by insufficient power supply, you can use a 2pin cable with an XH2.54 connector to connect the RPi5 GPIO to the 5V IN port.)
  • 15:39, 1 June 2025 172.58.114.209 talk posted a new comment on X1001 (Hello, I bought Geekworm X1001 PCIe to M.2 HAT from Amazon. I find that after an hour or so of use, I am getting I/O errors in my Raspberry PI 5 in the ssh terminal and all the UI on the screen freezes and disappears/ fails to launch. You have mentioned that it is possible to provide the HAT with extra power via XH2.54 5V power connector on the HAT. Can you pls explain how I go about doing that? What cable to use to connect to it and where should I connect that other end to source the power?)
  • 17:32, 29 May 2025 78.23.23.78 talk posted a new comment on EDP to HDMI Adapter (I have v6.2 30 pin of this board. Can't get it to work with my HP Omen15-ax201tx, the cable is DD0G35LC001)
  • 15:09, 27 May 2025 Lisa talk contribs posted a new comment on X1200 (Hello, How does voltage level corresponds with its level?-----Sorry we don't know, this value is returned by the power management IC. It is recommended to fully charge and discharge several times before checking whether the voltage and battery capacity are correct.)
  • 05:00, 27 May 2025 178.252.72.127 talk posted a new comment on X1200 (Hi! How does voltage level corresponds with its level? Datasheet shows that 3.7-3.87 V is 75% of charge. But the scripts (from software page) shows the following info: Capacity: 42.82% (Full) - Voltage: 4.07V. How to read the info and what is the correct charge level?)
  • 16:38, 26 May 2025 Harry talk contribs posted a new comment on X735-script (Hello, Run the command: <code>sudo systemctl status x735-fan</code>, you can get the speed of fan.)
  • 14:33, 26 May 2025 Lisa talk contribs posted a new comment on X1200 (Hello, Please contact us by email.support@geekworm.com ；Please send us a test video and let us known your order No.)
  • 10:02, 26 May 2025 Lisa talk contribs posted a new comment on X1009 (Hello, It's a SATA Power VH3.96-4P Connector；5V out for SSD/HDDs / GND/ 12V out for HDDs; Please refer to the X1009 V1.1 Interface Diagram.)
  • 10:01, 26 May 2025 Lisa talk contribs deleted comment #5829 on X1009
  • 10:01, 26 May 2025 Lisa talk contribs posted a new comment on X1009 (Hello, It's a SATA Power VH3.96-4P Connector；5V out for SSD/HDDs / GND/ 12V out for HDDs; Please refer to the X1009 V1.1 Interface Diagram.)
  • 23:46, 25 May 2025 212.244.255.209 talk posted a new comment on X735-script (Hi, I'm using the x735 3.0 version with Pi 4. My issue is that I cant make the fan spin form software position. I'm using volumio with PuTTy and setup everything right, however after installing the rpi.gpio and running read_fan_speed.py i get the same error as in FAQ. So i tried using "sudo apt update && sudo apt install python3-rpi-lgpio --auto-remove --purge" but the end message says "Unable to locate package python3-rpi-lgpio" And from my understanding it cant find and install the rpi-lgp...)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"